Having problems with your Whirlpool 24 in. GU3200XTP Built-in Dishwasher ?

Unit will not drain. It will fill with water in normal manner. Circulating pump also works normally. Float switch seems to be sound. But the wash water is not expelled as it ought to be.


Answers :

Something simple to check is the drain hose. I am an installer and have seen this many times and people will buy a new dishwasher after putting in a new garbage disposal. If you did, did you remove the knock out plug from the disposal? Next, remove the drain hose end from under the sink and try sucking the water out with a wet/dry vac. All the water from the dishwasher should easily be sucked out from any dishwasher except a GE brand. If not, your drain hose is clogged.
Repair Help & Product Troubleshooting for Whirlpool 24 in. GU3200XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Unit will not drain. It will fill with water in normal manner. Circulating pump also works normally. Float switch seems to be sound. But the wash water is not expelled as it ought to be.


Something simple to check is the drain hose. I am an installer and have seen this many times and people will buy a new dishwasher after putting in a new garbage disposal. If you did, did you remove the knock out plug from the disposal? Next, remov ... Whirlpool 24 in. GU3200XTP Built-in Dishwasher

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Tricity Bendix DH090 water valve closes too early. Insufficient water causes program to stop before first heating cycle. If I switch off, open the machine & pour an extra pint of water in, shut the door & switch on again the wash takes place and completes perfectly to specification. OK so the problem seems to be that level detector No 1 switches off the water inlet valve early and level detector No 2 (apparently) halts the cycle since it detects insufficient water in the machine. I cannot see t


... Tricity Bendix 18 in. DH090 Free-standing Dishwasher

Kenmore Dishwasher model 665.1675592 doesn't seem to wash as well as it used to. Seems to have a low water level. Filler valve works, allows water in, but never seems to fill enough. No spray reaches top shelf, I think due to insufficient water level. It's like the timer doesn't stay on long enough for it to fill. Also cycle time seems WAY up, but if the timer is slow, how does it time out filling so fast? Looks like it would be slow all the time. Suggestions?


... Kenmore Dishwashers

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

I think I need to check the water pump/motor on my Bosch SHU43C dishwasher. It seems the water enters at the start of the wash cycle but then there is silence through the remainder of the cycles. Water will not spray. The drain appears to work ok to drain most of the water out. I have the washer out and upside down. Any hints on removing the base to get access to the pump? Should AI be looking at the control panel also for a fault? (the cycles seem to count down ok)


Click below;\015\012Latest Bosch Dishwasher Use and Care Manual\015\012\011\011\011\011May 4th, 2008 by Samurai Applian ... Bosch Dishwashers

I have an Ariston LS245 dishwasher, have just had the pump replaced, as it had shorted out, due to water in the bottom tray where the water detection float is, also a new drain hose fitted. Have just run a wash and after running a while, presumably to the end of the rinse, wash and dry cycle, then one of the cycle phase lights, the one for 'soak' blinks constantly. I switched the machine off and had a look to see if a wash had been done, the dishes look clean. In the book it says that if one


... Ariston Technologies Dishwashers

I have a Frigidaire UC DW Model FDB250RHB2 The unit is not a year old. It is not getting dishes very clean. I read similar posts. I found that there is water coming from top nozzle but not a very impressive stream. It is weak enough that most of the water misses the funnel on top rack. Also not top or bottom arms spin. Last week when i would quick peek during wash cycle there seem to be water coming out of top arm's holes but no spin. We also are getting heavy white staining on glass ware


... Frigidaire FDB520RH Builtin Dishwasher

The water level in my Whirlpool Gold dishwasher does not seem to be high enough to clean the dishes. Also, the detergent dispenser opens but the detergent does not wash out of it. How do I increase the water level? Also, could it be something else besides the water level?


Screw fell into wash moduel. how do i remove the lower arm ect. Thank's ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Jackson jp-24b purchased this machine used, cant figure out how to work it. I flip the auto cycle on, and then the power switch. The fill light turns green and i assume water is filling up in the machine. In the meantime there are two small red external hoses that hot water comes and i currently just have those hanging in the sink. At the same time, nothing is happening during the wash cycle, the wash gauge doesnt even move only the rinse gauge. Also when i try to drain it nothing happends (begi


It needs a new drain relay box 120 volt the drain is stuck open the jp 24 were not very good machines the red lines are drain lines if you plug up the drian lines at fillup the machine will wash but now it will never drain a new drain box is not c ... Jackson JP-24B Built-in Dishwasher

Have a Karcher kb4040 that continues to run constantly even when the trigger isnt pressed. Also water flows out of the detergant hose when im not pressing the trigger. Pressure seems down slighlty, not much. This happened after i ran water out of trigger gun with no lance attached, machine switched on. Seems to leak from trigger handle aswell. Many thanks in advance


This is two things. One is the back flow check valve to the soap line is leaking. The other is the pressure switch on the output side of the pump. ... Pressure Washers

My Bosch SHY56A02 dishwasher won't fill....When cycle is started, it seems to pump water out but none in. Water feed is good....Added water manually and it pumps out immediately. Also, unit continues to run with door open...door switch is not jumpered. Could it be the fill valve? More likely the control module? Thanks for your help!


Hi,\015\012\015\012As water is filling in your dishwasher a float rises along with it. When the float reaches a predetermined level it shuts off the flow of water by activating a switch thereby preventing a leak. Sometimes the float can g ... Bosch Dishwashers

The dishwasher is cutting out the mains rcd switch when running? This happened during an intensive wash now as soon as you switch the on switch it trips the cut out! I have checked the both pumps for earth or neutral leaks and also the the heater but all seem fine. I only have a multi meter at my disposal so therefore cannot do a proper earth leak check. the machine is approx four years old and is not used very often.


Hello, dawhI\012 was trying to help you out here. I am not sure if this well help you? \012But here is a link to about everything you want to know about your \012dishwasher, from repair to trouble shooting on most common dishw ... Zanussi 32 in. DE6755 Dishwasher

Got a lound buzz type noise that I thought was a bad solenoid on the water valve. Tub also filled up & overflowed1 Replaced water valve ($30), but now dishwasher wont run thru cycles or fill with water to wash--seems to be stuck on drain even though digital counter counts down. What should I check next?


You may have dislocated the connection that controls the AquaStop circuit.\015\012\015\012This is linked to the inlet hose. Either the connector linking the inlet tap to the inlet valve is loose or the float switch has triggered.\01 ... Bosch 24 in. SHU53 Built-in Dishwasher

Asko 1716, the program will not advance. I changed the timer mechanism but that had no effect. There is no water leaks and the if i manually move the timer it seems to perform that cycle: water enters the machine, it will wash and will also drain the water out. any clues?


... Asko D1716 Built-in Dishwasher

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

I have the Quiet Partner II, DU1100XTPB7, and have already replaced the electrical ciruit board but having the same problem. When I hit any wash cycle button, the soak/scour & heated dry buttons light up, but will not "start." The "rinse only" button does nothing, but if I hit the "delay" button, then the soak/scour, cancel, and also the status buttons, washing & drying, all night up at once. The only button that seems to be working is the "cancel/drain." Although there's no water in the mac


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

My dishwasher (kleenmaid brandt super silent DW121TB) appears stuck in a wash cycle; how do I reset the program? I have read the instruction book to no available, tried unplugging power overnight, tried a combination of simultaneously holding buttons in and switching on, letting the machine run all night, drained the water and added clean unsudded water, and none have corrected the situation. There is also a selection lever inside the machine that is not identified in the instructions, it appea


When you say it is stuck in a wash cycle, do you mean the wash arms are continuously running?\015\012Is there water in the base when you open the door?\015\012\015\012Can you try to run the dishwasher in any other program like rinse ... Dishwashers

My Bosch dishwasher Model SHE44C02UC just went completley dead while washing. My wife and I were in the living room and heard a ''pop'' and went to investigate. We discovered the dishwasher was completely dead with no lights on at all. The on/off switch does not work. I checked the breaker and it is okay. Also the disposal is also on this circuit and it still works so I know the circuit is okay. There is still water in the bottom of the dishwasher - no suds - so it may have been in a rinse cycle


Well done on confirming that the outlet is not the problem. This problem will not be able to fixed by the owner and a service call is the next step. (unless you want to dig into the problem, which could easily be a failed pump motor which took out t ... Bosch Dishwashers

Dishwasher wont fill with water. just before it stopped filling i was turning the dial (a lot) between the wash cycles back and forth to attempt to get it to fill and drain (I didn't let it go through a cycle). We also removed the hose from the machine as it had split and replaced it and we had the machine tilted on it's side. the dial still clicks round but it sounds like the pump is going and it doesn't seem to be filling with water. Help


Hi. I suspect that the timer mechanism will be the culprit here, but i recommended to inspect and test the water inlet valve, before replacing the timer. The valve is a known problem area, as well. Follow the valve inspection procedure below, careful ... Fisher DS603W / DS603B / DS603I Dishwasher

I have a Kenmore model 587.1610 dishwasher that doesn't fill all the way when starting a load. I checked the float switch and it is working fine. The fill soleniod is also working fine and is clean. It just seems to time out before it fills all the way.also to compound the problem it doesn't seem to want to start all the wash cycle even after I have re-started the machine and it has filled to capacity. please help thanks Danny


... Dishwashers

Hi there I have a Bosch SGV4313GB/17 Dishwasher the problem is there insuffient water pressure to feed the washer arm and they are not rotating Ihave cleaned the arms and circulation pump impeller with white vinegar ,I have also overriden the door switch and operated the dishwasher with arms removed and the circulation pump seem to be working but with insuffient pressure also the machine does not fill to the depth it did when it was fine! How does one tell if it is the impeller or the


Ours is a SHU3300UC/06 model, basic model which we bought in 1999 so have had 9 years of trouble free service.Recently\015\012we noticed that there was soap left in the soap dispenser after the\015\012machine had finished all the cycles. On fu ... Dishwashers

I have a Kenmore Ultra Wash built-in Diswasher. The flap on the detergent door does not open as it should during wash cycle. Also, I thought the rinse aid was empty so I went to fill it and its obvious that it has not been dispensing either. Otherwise the dishwaser seems to work ok, but we have hard water & I've tried everything and still have residue on dishes.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. First of all please check the\015\012Water temperature by using a thermometer inside the dishwasher to measure ... Kenmore PRO 24 in BuiltIn Dishwasher with Ultra Wash HE Filtration 13173

I have a GE Profile, GSD4930X73WW, dishwasher. The upper wash arm is not spraying well at all. I checked the water line from the pump to the upper arm and it's fine. I cleared the filters and cleaned the float. I also took the inlet valve off and cleaned the screen. Although the washer works better overall, the upper arm still does not work well. Nothing appears to be in the upper arm assy to clog water from spraying out. All seems clear from the turbid sensor (next to the pump) through t


... GE Dishwashers

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e


The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1448 seconds