Having problems with your Whirlpool 24 in. GU3200XTP Built-in Dishwasher ?

My dishwasher seems to be locked up and needs to be reset. the clean led is constantly flashing. i had this trouble in the past, and the serviceman reset the dishwasher by using the touchpad on the front as a code and washer worked again. do you know the code.


Answers :

Control is programmed to
\015\012stop the current cycle and
\015\012not allow any further
\015\012cycles if it suspects a
\015\012faulty heater (no
\015\012temperature increase
\015\012detected in heated
\015\012intervals). Control blinks
\015\012the Clean LED 7 times in
\015\012repetitive fashion and
\015\012disables the Start/Resume
\015\012key until cleared.
\015\012Heater circuit problem:
\015\012■ Open in heater.
\015\012■ Open connection or
\015\012component in heater
\015\012circuit.
\015\012■ Faulty heater drive
\015\012circuit on control.
\015\012Running Diagnostics clears the control and
\015\012allows it to operate again. If heating problem
\015\012is not corrected though, the control will stop
\015\012running again on next cycle. See below.
\015\0121. Unplug dishwasher or disconnect power.
\015\0122. Check all components and connections in
\015\012the water heating circuit or heat dry circuit.
\015\012■ Check resistance of heater.
\015\012■ Check resistances of all connections and
\015\012components between the control and
\015\012heater.
\015\012■ Check operation of heater and temperature
\015\012sensor in Diagnostics cycle.
Repair Help & Product Troubleshooting for Whirlpool 24 in. GU3200XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishwasher seems to be locked up and needs to be reset. the clean led is constantly flashing. i had this trouble in the past, and the serviceman reset the dishwasher by using the touchpad on the front as a code and washer worked again. do you know the code.


Control is programmed to\015\012stop the current cycle and\015\012not allow any further\015\012cycles if it suspects a\015\012faulty heater (no\015\012temperature increase\015\012detected in heated\015\012int ... Whirlpool 24 in. GU3200XTP Built-in Dishwasher

I just replaced the heating element and it was working fine for about a week. Yesterday, the soak and scour light (which I've never even used) started blinking constantly. The dishwasher, Model GU2400XTPB3, won't let me even enter the reset code. I need to know if it's something we can fix without paying for another part/service by finding a manual. Thank you.


... Whirlpool Dishwashers

Reset code I recently had a problem with my dishwasher that required me to use a reset code on my control panel. I can no longer find the manual that tells me that code. I was wondering if anyone knows it as to save a tech call. The error occurs when the clean light flashes. We have checked the heating element and the tech told us there is no problem there, we just need to reset the machine. The error has occured again, but this time because I tried to run the machine right when we came home fro


I believe the reset sequence is accomplished by pushing the NORMAL WASH then HEATED DRY buttons in that sequence two to three times. The unit will enter diagnostics mode, but can be stopped by pressing the CANCEL button. Let me know if this helps. ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

We had an electrical surge that knock out some of my appliances. I went to the electrical box and reset all the circuit breakers. Everything worked again except my kenmore dishwasher model 22-16533. I am told there is a combination of buttons you push to reset the dishwasher, but I don't know the code. help!


Hi pedelz,First please check if your dishwasher is receiving power from the outlet.You can reset the control by pressing these buttons in this order\015\012fairly quickly: HEATED DRY - NORMAL WASH - HEATED DRY - NO ... Dishwashers

Whirlpool dishwasher reset code


Yup, found it on another site..I had the same issue today.\015\012\015\012Reset code: Push 1. Heat Dry 2. Normal 3. Heat Dry 4. Normal\015\012\015\012wait about 2 minutes as the controller resets itself. You should see all th ... Whirlpool 24 in. GU3200XTP Built-in Dishwasher

I have a Maytag quiet series 300, model # MDBTT60AWW. The front control panel have some green lights on but the start/cancel button won't work. The dishwasher will work for 5 days and quit for 2-3 days then work again. I tried to reset the main electrical panel hoping the dishwasher will reset too but it didn't work. I opened the panel on the front door to see if water is getting into the electronic panel but it is dry. I'm wondering if it is the front control panel itself is the problem. I want


... Maytag Dishwashers

Kenmore quietguard 7 dishwasher...clean light flashing, dishwasher won't run repair guy a few weeks ago couldn't come, but told my husband to push a couple of the buttons on the control panel, and it worked for a while... repair guy coming back on Monday, but I''d like to know the buttons to push to reset it so I can use it till then


... Kenmore 24 in. 15173 Stainless Steel Built-in Dishwasher

Kenmore Elite Drawer Dishwasher model 465.13329600 Normal Wash and High Temp Wash buttons stay lit, as does green Lock button. The Start/Resume button and the red button on the front of the drawer keep flashing. I've tried key combos suggested above, but nothing seems to work. Even tried shutting it off at the circuit breaker to reset it, and that didn't work either. This ****** was purchased in 2006 or 2007, and hasn't been used very much. WTF?


... Kenmore Dishwashers

Hi My F&P dishdrawer flooded. Dried it all out etc, the top drawer doesn't complete the cycle and it beeps continually even when it's not running. I am wondering if I can reset the drawer using the front buttons to get it back to factory default. Bottom drawer works fine. There is no error code on the screen only the lock icon which won't go away. Any ideas?


Not sure if you tried turning the power off at the main switch. Lock icon can gone away if you press the necessary keys as shown in the user guide. Also the sequence of keys to press for getting factory defaults of different options is also in the us ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I would like to get a user manual for LG dishdrawer model DD603, Australian model. Failling that what I really need to know at present is how to use the lock button - just pressing it doesn't seem to work. I need to be able to stop my toddler starting and stopping the dishwasher at her own whim! The front display has three buttons, 'power', LED display then 'Start/pause', & 'lock'. Thanks Shelley


Opps wrong make & model. Searched for fisher & Paykel and found what I needed! No longer need a solution. ... LG Dishwashers

I need to reset the mother board on my Kenmore dishwasher. Do you know the code for the Kenmore model 665-17032402. I was told by sears that they used to give this out but, because of a fire hazard they have stopped doing so.


The clean light sometimes flashes and just needs to be reset. To do so\015\012hit the keys in the following order. <Heated Dry> <Normal\015\012Wash> <Heated Dry> <Normal Wash> <Cancel>.The dishwasher will go throug ... Kenmore 17024 Built-in Dishwasher

Electrolux dishwasher EWDW6505 has error code 01 and then version 62 but don't know how to reset it


... Electrolux EWDW6505GS Fully Integrated Dishwasher with 9 Wash Cycles, Nylon Racks, Wave-Touch Contro... 24 in. Built-in Dishwasher

Maytag Dishwasher I need the reset sequence for my dishwasher. The power comany had turned off the electric to the house to make chages elsewhere in my house. When the electric was turned back on all appliance came back on except the dishwasher. The dishwasher has a front panel touch pad and three of the panel lights are flashing. I know there has to be a sequence to reset the machine. I also need the peace and quiet in the house since I am the husband and am suppose to know it al


We have a model mdvtt53aww1 and you can push three buttons and will light up the hi temp wash, heated dry and sanitize is there a code make it start ... Dishwashers

Quiet Partner II Whirlpool Dishwasher 2 years old, used about 6 times in 2 years. Panel LED's flashing like a Christmas tree: Pots / Normal / Sani / Cancel lights all flashing Tried different resets as found on web but none work. Dishwasher was NOT being used when the flashing started. Need reset sequence if there is one.


Unusual LED or\015\012Display Readouts\015\012Open ID diodes and/or LED\015\012circuit(s) in keypad, or open\015\012ci ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Dishwasher PLD 3465 REC I cannot reset the display panel. I took the kickplate off which was supposed to have the code for the reset but it had nothing related to reseting the display panel. It is stuck on 94 min clean time. What is the code to reset? There is nothing in the Use & Care manual that tells you how to reset.


Putting the unit into service mode will reset the the display. Look at the instructions behind the front panel. If the unit fills and does not wash, the wash motor may not be working. ... Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher

I have a Kenmore dishwasher, model 665.16039. Over the past month (we were on vacation 8 days over Xmas, but I assume it would have happened then, too) it has required rebooting using the Normal Wash - Heated Dry reset about 4-6 times. It would then do a couple loads okay, then need resetting. Now, however, it's refusing to reset to a point at which the Start buton will work. When I reset it, it flashes all the lights (incl. Start), and it fills, sprays, empties, etc. just as though it works


Make sure there is no water damage. ... Kenmore 24 in. 16039 Built-in Dishwasher

My tappan dishwasher is only 1 1/2 yr old and its not getting at least 1/2 of dishes clean. We have tried everything from changing to liquid soap, increasing water pressure at meter, not using while washing clothes. We used a dishwasher cleaner to remove calcium, and run hot water in sink before using. We know the wand, pump and drain are working. It is model TDB210RFB5 with 1.1A motor. Is the motor too small to clean dishes? I wish I could get my money back or exchange for an upgrade. Thanks!


... Electrolux Dishwashers

I have an old Bauknecht dishwasher GSF 3160 S that a friend gave us 10 years ago. It was stored for that time, and now if I try to use it, it leaks out through the bottom and floods the kitchen. I would like to know 1) is it worth fixing from the point of view of how energy/water efficient (or inefficient) an old dishwasher is - if you know the specs for this particular machine, and 2) what needs to be changed if it is worthwhile fixing. I don't know what else might not work, because I only pu


... Bauknecht Dishwashers

I have a whirlpool dishwasher Quiet Partner IV. Every 3/4 months I have to reset it because it will not turn on and perform a wash cycle. The appliance repair people only reset it and charge me $40.00 and do not give me the code. I found the code on the internet but now that code is not working ''High Temp, Air Dry, Air Dry, High Temp, Air Dry, Air Dry.'' Any other suggestions?


... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

Smeg e2 error (water level tripped). Filter is clean and no rubbish below filter on inside of dishwasher. I have taken the front panel off but am not sure where the float device is located - I am wondering if it is just to the left of what looks like a solenoid. There is no water in the base of the unit in the front panel so would rule out any leaks. Reset program and turned off power at socket but still not using hot water. Possible PCB issue ? Any advice appreciated. Smeg DI612C Dishwasher.


... Dishwashers

We have a turbothermic Miele dishwasher...It tells me it has a blocked drainage outlet...took it apart ,no blockage,cleaned the pump area of any debris but all clear...I rang mile support and they told me to try resetting it ....I t did work and we used the dishwasher..but it has the same problem again ..cant't remember how to reset it ..


I hope this information will be helpful. ... Miele Dishwashers

I have a GE Quiet Power 3 dishwasher that was working fine last week. Over the weekend I ran it and we could hear a banging noise, so my boyfriend opened it three or four times in a row (during the cycle) to figure out what it was. The fourth time, it went dead. I checked and it had tripped the breaker. I reset the breaker and the dishwasher seemed to be working again, however the lights on the front were flashing (they hadn't previously), and now it will run for about 10 minutes but no water ru


Were you able to figure this out? We have the same problem here! ... Maytag Dishwasher

A feew weeks ago Smeg STA6047 dishwasher stopped in the beginning of the programme after approx. ten minutes, and gave the error code E9. There had been clearly water in the machine, but maybe not enough and the detergent box was not open. However, when technician came by two weeks after, the dishwasher worked and he said it was in order. But only after being used only once, the same problem reappeared. First the washer gave the error code E8, on the second try E9. And now it does not start at a


As you know E9 is linked to the water inlet problem. \015\012\015\012There are two scenarios here - 1) Are you using the Aqua-Stop safety system? If this is trigerring then it can shut the inlet water. The reason it can trigger is if the ... Smeg Dishwashers

Towards end of dishwashing cycle error code comes up and consitently beeps, can not turn off by machine buttons or reset. We have to reset by power plug. Water is left in bottom of macine, dishwashing powder is left on most things. Rinse button then works, it then drains the machine no problem. So I dont think it is the pump.


No response ... Dishwashers

Top arm does not turn in most of gibson amana an frigidaire this is done by ball in bottom of pump .it is clean.spray arm are clean .bottom arm move all the time.timer works it hesitates every so often and so ball will move an water should go up to upper arm but doesnt.common problem on these units but dont know how to cure?change ball.didnt work..on one unit changed pump cure problem for 4 months then returned....also does anyone know were u can buy the plastic they used to sell for dishwashers


Can yo give me the make and model number sol I can look at the service manual for you? ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2032 seconds