Having problems with your Whirlpool ADP 252 WH ?

Why do the program progress

The program gets stuck in one position

Answers :

Repair Help & Product Troubleshooting for Whirlpool ADP 252 WH

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When starting my Bauknecht GSFP 5586 dishwasher the program is set for rinsing and the start light flashes two blinks, then again two blink etc. I cannot get the program to change. When I hold the Start button for 2 seconds, the progress light flashes at END for a moment then reverts back to the double blink sequence. I have checked the filter and it is well seated and clean. What can I do to start the program selection again?


Ok, so I had the exact same problem with the exact same model. NOT 7 blinks and to buttons that you do not have.\012I will tell you what I did as I do not know what (if any) of what I did fixed it (it could be luck but I do not think so).\012 ... Dishwashers

My Tricity Bendix DH101 was short circuiting and I could not put the trip switch in the mains box on unless the dishwasher was unplugged. I got in an electrician and after he fixed it , the dishwasher does not progress with the program. It just keeps churning on.


... Dishwashers

My name is John, I have a Fisher&Paykel DD603 bought in Jan 08 and have a problem with the program selector, which is stuck on 12 min and will not progress to anything else. It seems that the arrow button does not respond. The eco button goes on and off by pushing the button. I disconnected the power, hoping for a reset of the logic board but had no luck with that attempt. Any advice available?


Hi\015\012\015\012The issue is with the control panel/key pad that is bad and it should be replaced. Hope this helps...please post back for further assistance.\015\012\015\012Daniel ... Fisher and Paykel Dishwashers

I have a nobel model nbfsd/w when swithed on the pump starts but nothing else happens and the program dial never progresses it is 4yrs old and a similar problem occurred while it was still under warranty. is it worth fixing . please help


... Dishwashers

When I push ON button on my Siemens 54230/07 (FD 7706) it will not start. The display which normally indicates the progress of the program now shows 1 or |. Nothing else happens, no sounds. What could


... Siemens Dishwashers

Hello, We have a Candy Diswater that is just arround 2 years old. When it starts it takes water and then you hear the washer going into loop. It tries to do something els but doesn't seem so. If you open the door you can see water inside but no progress or heating. If you also try to change the program it doesn't change as well. Before it got to this point sometimes we used to unplug the power and tunr it off and then ON and then it works. However, now this procedure is not working an


Quite possibly could be the timer and could also be the main control board as well. Sometimes unpluging it will help for short times but if a serious problem persists it will only be a temp fix... ... Dishwashers

Aeg favorit 6281 I-M turns on but all programs revert to bio and then will not start


... Dishwashers

Kitchenaid does not do the program, I can start the program, but about 15 minutes into the program the program stops and the light jumps to clean light which it 7 times blinks pauses and 7 times b


Clean all the buttons , one must be stuck , push all the buttons and un stuck them.... ... KitchenAid Dishwashers

Any of the programs start ok (water enters etc..) but the program does not move on, will stay at the same place early in the program cycle for hours. You can move the program on manually and the water ext will exit but the dishes are not properly washed. Changed program timer switch but still same - zdi6041x dishwasher - any idea why ?


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Zanussi 23 in. ZDI6041 Built-in Dishwasher

Bosch Exxcel Auto Option, 2004. SGS56E02 GB/47 Stopped mid program all program lights flashing, on re-set several program lights illuminated, able to select rinse program but several lights illuminated and fails to pump out at end of rinse. What has gone wrong?


... Bosch 24 in. SGS57E02 / SGS57E08 Exxcel Free-standing Dishwasher

I have a older Simpson 880 Dishwasher, 6 program, (circa 1995) that I got second hand. It works quite well, but due to its usage the dial which has the program on it has worn and is very difficult to read. so what I need I suppose is another program dial or someone who can tell me via a photo what is marked on a dial you can actually read as mine is worn off and is for the most part indecipherable. I can read where program 5,6 and 7 are but not anything else, I got a instruction book from ELectr


In regards to your program dial, there is a number 4 2 clicks in front of the 5. That's for normal wash. There's #3 for heavy wash, a #2 for pot scrub and #1 for pre-wash. There are two "clicks" in between each #. There's an R for "rinsing and a D fo ... Dishwashers

The program control on my flavel fdw60 dishwasher has all the programs showing up as selected and will not advance onto one single program


... Dishwashers

Used some washing up liquid instead of dishwasher tablets, after i got rid of all the bubbles and drained it, it no longer starts. If i switch the power off and leave it for a few minutes i can select a prgram it starts and a few seconds later there is a beep and the solid green run light on the program selectoe is flashing over the left hand program button. At this stage pushing any program button does nothing, i have to swith the power off and wait 5 miniutes and the the above patten is repeat


Dear sir vif you have used liquid soap in your dishwasher it will make mountains of bubles to kill all bubles outin a hurry take a sos pad put it in your machine and run the dishwaser this will remove all of the soao instantly try it it really works ... Ariston Technologies Dishwashers

I have a Siemens SE25A836GB/35 dishwasher. the program is running and it sounds as if the pump is running all the time. I have tried resetting the program but to no avail. I have checked the filter CLEAR and the water supply is okay. The display in the front which state time to run on the program is blank can you solve the problem?


... Siemens 24 in. SE25A836GB Hi-Line Free-standing Dishwasher

Hi, I have a zanussi DE6744S. I can select any program and water fills as normal. The problem is that the cycle runs and runs and dosn't stop unless I turn the machine off. When I restart the machine it just carries on until I press the current program button in for a about 10 seconds and the program stops. On the odd occasion it ends normally on the economy cycle (30 mins) but its pot luck. It does wash as normal but dosn't seem to get past constant washing (no drying) . Hope you can help, S


... Zanussi 24 in. DE6544 Built-in Dishwasher

Dishwasher hello cant set program , when i push P it goes to selected program but when i start it came back to second program and runs that one


It could be you opened the door before it had fully completed a program, and then turned it off. My Hotpoint machine has to be reset in these circumstances otherwise the next time it is turned on, it appears to let you select a different program but ... Hotpoint Dishwashers

Program sticking for some reason the program keeps returning to the eco setting whatever buttons or programs we press


Problem sorted we returned the dishwasher to where we got it from but thanks anyway ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Smeg dishwasher ST1145S is not working. After I entered the selected washing program and closed the door, the program faked to start. I am not sure is because of no prolonged disuse or because of I have forgotten to turn off the on/off switch for almost 2 months but I heard there is a beeping sound which supposed to start the program and water intake. But all this is not happening.


... Smeg STX2 Dishwashers

Hi, I have a Siemens SE24A230GB/17 dishwasher and it is not completing the wash cycle (any selected). It appears to be stuck on the 'wash' part of the program. I have done the reset actions as advised in the User Manual and tried another program, without success. I have found that the possible causes could be the timer or thermostat. The estimated time remaining display counts down, but the program does not complete the wash and move onto rinse and dry. Any help or advice you can provide would


... Siemens Dishwashers

We understand that your problem is: My AEG F60879UM, pnc 911946608 03, sensorlogic stops during program, the front opens and it will not continue the program. First it was in the middle on the program, now it is in the beginning. No fault code shows. What can be wrong. .


Hi\015\012\015\012The issue is either with a bad door lock-switch assembly or\015\012the timer/control has gone bad. Though I believe as the unit starts however,\015\012stops in middle of cycle it is the timer that should be replaced. Hop ... AEG Dishwashers

The program indicator light is on constant, but will not change programs when pressing the program selection button. And when you close the door to start the cycle nothing happens


Hi\015\012 \015\012Please check the link regarding your query…\015\012http://www.rep ... Dishwashers

Smeg dishwasher ST1145S is not working. After I entered the selected washing program and closed the door, the program failed to start. I am not sure is because of no prolonged disuse or because of I have forgotten to turn off the on/off switch for almost 2 months but I heard there is a beeping sound which supposed to start the program and water intake. But all this is not happening.


... Smeg 18 in. STX45-1 Stainless Steel Built-in Dishwasher

Program stoppage Dear Fixya, Greetings from sunny Greece, My dishwasher wont work when i choose the program 55 Universal plus and 65 . When at this programs, it stops and some amount of water is left on the bottom. Any ideas of what the problem is? Best Regards,


The problem could be due to your heater not going on. The unit will run but when it goes to heat up, it will atempt to do this for a while, but will be timed out. Are any lights flashing, as this is an error code. You will need to get a service te ... Miele 24 in. G656SCi Plus SS Built-in Dishwasher

I have a de dietrich built in dishwasher model DVH610JU1. The program appears to start but no water enters the machine and when I open it the lights flash (program light and end program blue light)


... De Dietrich 23 in. DVI130 Built-in Dishwasher

Program The selected dial up program wont light up. Will only run on the rinse/drain program. Seems to be draining O.K.


Try to see if it flashes an error code, that could help identify the problem. Otherwise, if the problem is only with programming and not with the actual dishwasher, you might want to try replacing the program timer module. ... Whirlpool ADG332 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0310 seconds