Having problems with your Whirlpool Dishwashers ?

Dishwasher DU1100. Odd behaviour during cycle: "Washing" light goes off and sound of washing stops. "Normal" light starts blinking and "soak and scour" light comes on (it was off before). No sound from washer. This persists for at least 10 hours. After that, the lights go off. Is this normal behaviour? It would appear tha the drying cycle did not go.


Answers :

No it is not normal. It appears that either the membrane switch pad has failed or the control board has failed.
Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher DU1100. Odd behaviour during cycle: "Washing" light goes off and sound of washing stops. "Normal" light starts blinking and "soak and scour" light comes on (it was off before). No sound from washer. This persists for at least 10 hours. After that, the lights go off. Is this normal behaviour? It would appear tha the drying cycle did not go.


No it is not normal. It appears that either the membrane switch pad has failed or the control board has failed. ... Whirlpool Dishwashers

Cranky dishwasher I have to admit my wife's solution is the only one that works. Our ten-year-old Superba built-in usually starts a normal cycle part-way through, at the wash part, without filling or opening the dispenser door. Therefore the dishes come out with the soil now baked on. Closing the door, selecting normal and start results in a pump-out sound, or at least just the pump running to wash the dishes. The dishwasher ignores any cancel button push,and the light does not come on over t


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the s ... KitchenAid KUDS24SE Built-in Dishwasher

My accusense light keeps coming on and blinks continuously. I tried the heat-dry, normal sequence and it would reset to 2 minutes. After the 2 minutes cycle, the accusensor blinking would begin again. Then I tried holding the heat-dry button in for 5-seconds. This looked like it worked so we set a normal cycle without heat-dry. Äll looked good, but a few minutes in, the normal light was off, the accusensor was blinking again and the heated-dry was on again! Is the unit possessed? Other id


... Whirlpool GU2400XTP Built-in Dishwasher

My GU 120 stops mid cycle and the indicator light starts blinking a humming whirring sound preceeds the ctcle stop nad light blinking. Pressing the button for 5 seconds causes the flashing light to extinguish but the sound continues untill the unit stops. It does not complete the full cycle. Your help would be appreciated. Tony


... Whirlpool Dishwashers

My Kenmore Dishwasher 665.16359301 quit working. I flipped off the breaker then back on again. The cancel light comes on and it sounds like its going to drain but theres no water in it. After about 20 seconds it stops and the normal wash cycle light starts blinking. Thats it. I did the reset procedure and it started to work then went back to the normal wash light blinking.


... Kenmore Dishwashers

I have the Whirlpool DU 1100 dishwasher and the clean light kept blinking. I did the heated dry, normal combination and got it to run through the diagnostic check and sure enough it cleared the lights and appeared ready to run. When I would start it up again it would run the water and then get to the soad wash cycle and stop. No more lights it just stopped. I have been through the diagnostic process 3 times and still same problem. HELP


... Whirlpool Dishwashers

My Maytag dishwasher model MDB600AWB, serial 18721619CN Quiet Series 300 will light up on the panel except for NORMAL WASH and START. It will not run. All other buttons work. It displayed the number 9 and the RINSE ONLY light came on after we got off the phone with Maytag. Initially nothing would light at all. We changed the fuse (it is NOT on a breaker) and it again didn't light. A few minutes later it did light the above mentioned buttons.


... Maytag Dishwashers

Model KUDS30FXSSO, Unit attempts to start. Blue light on the front of the door comes on indicating the cycle is starting. Pump runs a few seconds as normal. Then the maching sounds like it trying to start the next step three or four times. The blue light goes out. The washing cycle then switches to cancel/drain, ( I opened the door to see which control lights were on.) runs the drain pump then stops. The green light on the front panel does not come on indicating the cycle was completed.


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

After a power outage, that occured while the dishwasher was running, the lights come on and there is a high pitched noise. Then all the lights go off and the motor sounds like it is starting. However there is no water and the heating elemant comes on. The lights on the front; china/crystal, normal wash, clean and heated dry, all come on as if the computer is confused and trying to run them all simultaneously.


Sounds like the board was fried from a power surge ... GE Tritonr XL GSD6260JCC Dishwasher

Kenmore ultra wash quiet guard dishwasher, the pots and pans and the normal wash button are blinking. The start and cancel and smart wash out tons have a faint light glowing. Thoughts? I tried the sequence of pressing heated dry, normal wash, heated dry, normal wash and that did nothing. I've flipped the breaker too. I was in process of taking it apart to clean filter, thinking that would help, but lost my manual and now I can't get that off to flea either:(. Sig


... Kenmore 24 in. 15689 Built-in Dishwasher

Unable to start dishwasher, only functioning light on the panel is the cancel/drain light. push that button the machine funtions for a minute or two and shuts off,also the light above normal wash is blinking. When the machine last functioned it would start with a very high decibel level.If its the circuit board I need an approximate replacement cost. Bob


If you go to searspartsdirect.com you can get the exact cost of the module. ... Dishwashers

Bosch SHX33A: lights come on properly in response to buttons, it has power. Close door, it makes the normal startup sounds, then water flows in. Normally, at this point washer starts into normal cycle. Instead, it just sits there and nothing happens. Forever. Not a matter of patience: we've left it in that state all night long. Have flipped power circuit and started over, everything else I can think of to kick-start it, no change.


Hi\015\012\015\012The issue seems to be with the motor or the door latch\015\012assembly going bad and should be replaced. The washer won't start the cycle if\015\012motor is not working, as its filling with water so I believe that the do ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

Our 2470scvi has caused all of our glassware to turn white. we use very little soap and we always use rinse aid. It seems to me that it is not rinsing properly. It actually has a sound for about 10 seconds that sounds like a motor is stuck.. This sound occurs twice in each cycle. It seems to wash ok but not great of which I would expect for a supposedly top of the line machine. This problem has always happened and the machine is 3 years old.Is this normal for a miele? If so its not the machine w


Hello macit. I do not blame you one bit for being disgusted about this machine. Let's do this. Empty it out and pour in 2 fulll cups of white cider vinegar. Close the door. Let the hot water run into the kitchen sink until it is as hot as it wil ... Dishwashers

GE triton II dishwasher normal light flashes and beep sounds


Ran across this today. Ge dishwasher normal light just blinks and beeps when latch is locked. I had to replace the control module and it repaired issues right away. Hope this helps ... GE Dishwashers

About 7 or 8 minutes after setting my dishwasher to run a "Normal" cycle, I noticed that it didn't sound right. The Sensing light and the Add a Dish light were both on. I hit cancel and opened the door to find the inside totally dry and just barely warm. It had a slight smell - probably from the motor trying to run unsucessfully. Is there something I can do to remedy this issue without calling a repairman?


Check inlet water flow to your machine. Try pouring water manuallyin the wash chamber. If machine works OK, it is inlet water problem.Remove the hose and watch for free flow.Clean the strainer attachedto the machine. Beyond th ... KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher

I have a frididaire proffesional series aquasurge with speed clean dishwasher # PLD4375RFC3 dishwasher there is an Er code that just keeps flashing the china/crystal light is flashing as well as the low rinse light. it used to sound like it was running when you would close the door but nothing was happening inside. any ideas?


... Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher

Model# fgbd2431kb.All 4 lights flash on right.We press cancel and normal wash and the lights keep flashing and sounds like drain pump runs.


... Frigidaire Dishwashers

I have a Maytag Quiet Series 300 Dishwasher (can't find any other model number etc). The normal and high temp wash lights are steady and the Start/Resume light is flashing. I've tried turning off the power and the high temp, heated dry, high temp, heated dry sequence but nothing works. Any help would be really appreciated! Thanks


... Maytag 24 in. MDB5651A Built-in Dishwasher

My AEG 18 in. Favorit 54750Vi has stopped working. It sounds as though it's going to start normally then starts to beep. When I open it the 'Rinse and hold', 'Normal 65*',and 'Intensive 70' indicator lights are flashing. There doesn't appear to be any water going in.


If for any reason (water leak)the anti flood device at the bottom of the washer is triggered it automatically stops the inlet of water via inlet solinoid and puts the washer in pump out mode. Check the float (polystireene plate with micro switch at t ... AEG 18 in. Favorit 54750Vi Slim-Line Built-in Dishwasher

I have a Kenmore dishwasher, model 665.16039. Over the past month (we were on vacation 8 days over Xmas, but I assume it would have happened then, too) it has required rebooting using the Normal Wash - Heated Dry reset about 4-6 times. It would then do a couple loads okay, then need resetting. Now, however, it's refusing to reset to a point at which the Start buton will work. When I reset it, it flashes all the lights (incl. Start), and it fills, sprays, empties, etc. just as though it works


Make sure there is no water damage. ... Kenmore 24 in. 16039 Built-in Dishwasher

Whirlpool Gold Quiet Partner Model # GU980SCGQ2 The dishwasher normal light flashes on and off continually. The dishwasher won't stop cycling now, everything seems to work normally other than it won't stop cycling. I've attempted turning off the breaker- no luck. Attempted resetting the dishwasher- no luck. Any assistance would be appreciated. Is this a problem with the control module? The thermal fuse?


... Whirlpool 24 in. GU980SCG Built-in Dishwasher

My Kenmore Dishwasher 665.16359301 quit working. I flipped off the breaker then back on again. The cancel light comes on and it sounds like its going to drain but theres no water in it. After about 20 seconds it stops and the normal wash cycle light starts blinking. Thats it.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Kenmore Dishwashers

Last night i loaded my kitchenaid KUPD01FLBL2 dishwasher, hit the normal button (green light came on), pushed the start button and went to bed. This morning I opened the dishwasher and it had not run. I tried again, Ihit cancel and then normal and start again. Would not start. Help?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or\015\012door lock switch which is not engaging its ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

DU1145XTP The buttons don't all work--for a while the normal wash and heated dry were the only functions that worked--now the start button doesn't work. I took the panel off and clicked the door switch and held it and got all the cycle buttons to light up except rinse only and only heated dry in the cycles would light up. The delay buttons don't work and neither does start. Also the panel seems hot.


You need to replace the circuit board inside the machine, technically it is possible for you to do it, how long have you had the machine, if it is under warranty you can have it serviced without any cost or less cost to you contact Whirlpool ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1171 seconds