Having problems with your Whirlpool Dishwashers ?

I HAVE A DISHWASHER QUITE PARTNER II MODEL. THIS CLEAN LIGHT IS BLINKING AND THE DISHWASHER WILL NOT START. LAST TIME THIS HAPPENED I PUSH A SERIES OF BUTTONS ON THE FRONT OF THE MACHINE


Answers :

You have to press a series of button in sequence, the sequence is\015\012completed pressing the Hi-Temp wash, air dry, Hi-temp wash and air dry\015\012again in succession.
\015\012
\015\012On some model it can be Sani Rinse wash, air dry, Sani Rinse and air dry again in succession.
\015\012
\015\012If that does not work, then try tripping the circuit breaker for two\015\012minutes, emptying water that can be eventually inside the tub,\015\012connecting back, and doing the reset sequence again.
\015\012
\015\012See also the diagram here.
Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I HAVE A DISHWASHER QUITE PARTNER II MODEL. THIS CLEAN LIGHT IS BLINKING AND THE DISHWASHER WILL NOT START. LAST TIME THIS HAPPENED I PUSH A SERIES OF BUTTONS ON THE FRONT OF THE MACHINE


You have to press a series of button in sequence, the sequence is\015\012completed pressing the Hi-Temp wash, air dry, Hi-temp wash and air dry\015\012again in succession.\015\012\015\012On some model it can be Sani Rinse wash, air dry, ... Whirlpool Dishwashers

I have a Maytag quiet series 400 dishwasher. I set the required buttons for a wash, inserted the soap in the soap tray but the machine will not start. Previously, when the washer would not start, I opened the door and pushed down on the soap tray and its seemed to fix the problem. Next time I used the machine, again not starting, but by pushing on the soap tray it would not start. Can you suggess what the trouble may be or give me a check list that I may do before starting the washer. This machi


... Maytag Dishwashers

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Kenmore dishwasher 16934 will not start up for me. I can push any button to set the cycle(pots & pans, china gentle, quick rinse, normal wash) and the time shows up in the display, but when I push the start, two red horizontal lines appear in the time remaining display. Cannot get the machine to start anything. All cycle buttons give me some kind of time remaining display but as I said, it ends up with 2 red lines. Thanks in advance. Mark


... Kenmore 24 in. 16934 Built-in Dishwasher

I have a Maytag Quiet Series 100 dishwasher. There is an icon with a "3" in it just to the left of "heat dry." I just noticed this "3" light is on and the dishwasher won't start when I push the "start/cancel" button. All that happens is the "3" light flashes when you push any of the other buttons, but it won't do anything else. Any help you can give me would be greatly appreciated. Thank you.


The "3" means hold for 3 seconds to child proof it. When it's on, none of the functions work. When you hold it again for 3 seconds, it turns off and your buttons will work again.\015\012Good luck! ... Dishwashers

I have a maytag dishwasher mdb5601awb. when I hit the start button nothing happens. I have found the instructions to do a manual test which is hitting the heated dry button 5 times and then the start button. Thinking it will run some test which I have no idea what to look for, it actually runs the machine's wash cycles and clean, dries and tells me it clean with the green light goes on. How do I reset/reboot the machine so it starts by just hitting the start button again?


... Maytag Dishwashers

Viking dishwasher M# DFUD142-PSS drains a little bit only then starts refilling, start button is blinking. When pressing the 2 buttons to drain have to press several times until responding then it drains just fine, also no push button light is on when pressing for drain. After doing all this machine worked fine for one wash only, then the same problem again after the wash cycle the water stays in the machine. Please help, thank you


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

Have whirlpool gold dishwasher made in Mexico, the control lock light stays on, when i push it and hold it just blinks three times and then stays on steady and then does the same over and over, before it did this I noticed the lights for different cycles flashing randomly, and even pushing cancel button once in a while would start the machine up....I have tried to unplug the machine and then plug back in, but nothing is helping....any ideas??


... Whirlpool Dishwashers

The Clean light on my DU1100XTPQA is flashing. The last time this happened, the service company walked me through a series of buttons to press in order to reset the dishwasher. Do you have this button series to press?


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

We have a Whirlpool GU980 Series Dishwasher. All the lights work. No matter what setting I use, it fills up, and then nothing happens. The "washing" light will be turned on, but nothing happens. I try to drain the machine, it will make a sound like it's going to begin a process, then it just stops. Do these things just "die" after some time? This machine is 7 years old.


Sounds like something is caught in the pump impeller. you will need to take the pump apart inside the tub. ... Whirlpool GU2400XTP Built-in Dishwasher

Our Frigidaire Dishwasher buttons stopped working. If we push normal cycle it will not select as well as other cycles. The last time it happened the maintenance guy came and turned it on and off and it started working again. That didn't work this time. We still can't select some of the wash buttons


You will have to replace that selector switchhttp://tclaundryrepair.com/ ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Maytag dishwasher mdb7601 will not run- light doesn't come on and nothing happens when you push the buttons. Earlier it would work but if you pushed the light cycle button the longer cycle would light up and it would run. Then the time running light did not light up.


... Maytag MDB7100AWB Dishwasher

We use our dishwasher daily. However, we have noticed when we have not used it over a series of days water is gathering in the bottom of the dishwasher and leaks onto the floor. We are able to drain the water by pushing the drain button on the front of the dishwasher. Any suggestions for issue/repair? The dishwasher is a Kenmore.


Hello, Welcome to FixYa ! \015\012 \015\012The problem you're experiencing based on your description sounds like (unfortunately) a common one. \015\012 \015\012The water inlet valve can be an issue with dishwasher's if they fail in the open po ... Dishwashers

I just bought this house with this dishwasher built in. I have pushed the door shut, pressed the heat dry button to lock the door and pressed the start button. Nothing happens. Now I can't even get the lights on front to turn off. The lock button flashes as though the door is open, but its not as far as I can tell. I have to press the latch in to open the door. I'd like to use it... any ideas. Its a Kenmore Elite model # 665 17052 402. Thank You


... Kenmore 24 in. 17052 / 17054 / 17059 Built-in Dishwasher

Dishwasher does not start, on any cycle selection. the only button that works is the cancel button which tells me the unit has power. this has happened before and a service tech was called and it "magically" started after he pushed the cancel button, not so this time??


Make sure the floor is dry where you are standing. \015\012 \015\012Push the cancel button twice in quick succession to attempt to turn the washer off.\015\012 \015\012Open the door all the way and look over t ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

I'm having trouble starting my ge profile dishwasher; the machine locks but then when I push the start button one of three things happen: 1) I get error C3 and I do not have a user manual) 2) nothing happens 3 I get the screen indicating that the machineis a sensing soil level, washing' but in fact nothing happens - I do not hear the motor starting and no water runs, thank you!


... GE 24 in. Profile PDW7800 Built-in Dishwasher

I have a smeg free standing dishwasher model df612sdx you turn it on and it bleeps once with a green light on one of the programs. If you push the p button nothing happens along with the start button. If you turn it off and on a few times the program light moves and occassionly it will start then stop a few mins later. Any ideas. Thanks


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or\015\012door lock switch which is not engaging its ... Dishwashers

I have a Kitchen aide dishwasher Model KUDI01ILWH6 that will not turn on..there is a control lock light on and I have tried pushing the cancel button but all that happens is the control lock light flashes 3 times and the dishwasher still wont turn on....Please , how to I disengage the control lock


... KitchenAid Dishwashers

Whirlpool 940 Series Dishwasher, Model #: DU940QWDQ3 I have lights on the control panel but when I push the buttons, all I hear is a click a few seconds later. The click is coming from behind the control panel. Nothing else happens. Dishwasher is about 14 years old


... Dishwashers

Our dishwasher beeps twice when the start button is pressed but then doesn't do anything and there is no other noise from anywhere (eg, motor/pump). There are no error codes displayed and the display appears normal (ie lights up and shows time for program completion etc). When the problem first occurred the machine was full of dirty water. We have turned the dishwasher off and on at the wall, checked/cleaned all filters, drained the dirty water and still nothing happens (it doesn't even fill


... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

We have a Bosch dishwasher. The manual says for models SHV46C13, SHX43C0 so I guess it is one of those. It stopped working and when I opened it there was a bunch of cloudy soapy water on the bottom. The power was not coming on at that point. I have noticed that lately when I go to push the on button, the light will go on and when I shut it it doesn't start. After a couple times of turning it off and on it will run normally. This has only happened a couple times though....


... Bosch Dishwashers

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

Whirlpool 940 Series Dishwasher, Model #: DU940QWDQ3 I have lights on the control panel but when I push the buttons, all I hear is a click a few seconds later. The click is coming from behind the control panel. Nothing else happens. Dishwasher is about 13 year old.


... Dishwashers

My cda dishwasher cw448 is 18 months old, and has recently begun to stop before the end of the cycle. When I open the machine, 3 lights flash, (one of them the rinse button), and the machine bleeps repeatedly. Why doesn't the cycle complete? I've checked the filters, the spray arms, all the dispensers, and manual doesn't give any answer. This doesn't happen all the time, but is occuring more often now.


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2475 seconds