Having problems with your Whirlpool Dishwashers ?

Whirlpool GU2300 built in Dishwasher. It rather suddenly began shutting off in mid-cycle. If I cancel or open it, getting it to finish the cycle or even drain takes many tries.Once started, the cycle might take several hours with long pauses during the cycle. When it puases, none of the lights are on at all. If the cycle is disturbed, the normal wash light blinks, and if I hit cancel, the cancel light and the normal wash light blink.


Answers :

Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Whirlpool GU2300 built in Dishwasher. It rather suddenly began shutting off in mid-cycle. If I cancel or open it, getting it to finish the cycle or even drain takes many tries.Once started, the cycle might take several hours with long pauses during the cycle. When it puases, none of the lights are on at all. If the cycle is disturbed, the normal wash light blinks, and if I hit cancel, the cancel light and the normal wash light blink.


... Whirlpool Dishwashers

I have a Sears Kenmore Elite Ultra dishwasher 665.1315 model. For the last 3 weeks, it keeps having the clean light blinking 6 times pause then 1 blink and pause and repeats cycle again. I have turned off the breaker...I have reset by pressing the heated dry and normal wash until all lights are flashing. It then completes some type of cycle and looks ok. When I opened the door, steam came out and all was hot inside. However, once I try any new wash cycle, it seems to wash but after 1-2 hours and


Call sears service and tell them you need service there is a service flash and will be no charge ... Kenmore 24 in. 15932 Built-in Dishwasher

Dishwasher DU1100. Odd behaviour during cycle: "Washing" light goes off and sound of washing stops. "Normal" light starts blinking and "soak and scour" light comes on (it was off before). No sound from washer. This persists for at least 10 hours. After that, the lights go off. Is this normal behaviour? It would appear tha the drying cycle did not go.


No it is not normal. It appears that either the membrane switch pad has failed or the control board has failed. ... Whirlpool Dishwashers

Whirlpool GU2300 Dishwasher. The machine stops for long periods during the cycle. All lights go out. If the machine is opened before the cycle finishes, it will not resume. If I try to restart, the normal wash light begins flashing. If I then try to cancel, the canel light and the normal wash light flash.


I have reviewed your problem with the Whirlpool GU2300 Dishwasher and have the fallowing suggestions for you.\015\012First, unplug the power to the unit and let it sit for a few minutes. This will clear all internal error messages ... Dishwashers

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

I have a kenmore dishwasher model number 66513729k600 and has the start resume, cancel drain, and the normal wash blinking lights and doesn't do anything i unplugged for several hours and is the same. what can i do???


... Kenmore 24 in. 16032 Built-in Dishwasher

Dishwasher takes 3 hours to wash, even on the light cycle


Whirlpool Quiet partner 3 the clean light is flashing 7 times what does this mean ... Whirlpool Dishwashers

My Kenmore Dishwasher 665.16359301 quit working. I flipped off the breaker then back on again. The cancel light comes on and it sounds like its going to drain but theres no water in it. After about 20 seconds it stops and the normal wash cycle light starts blinking. Thats it. I did the reset procedure and it started to work then went back to the normal wash light blinking.


... Kenmore Dishwashers

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

Heavy duty and normal wash buttons flashing together...4-hour delay button has a steady light. I unplugged dishwasher, I have pushed cancel, cancel and heavy duty and cancel and normal wash together.


Sounds like a logic board problem. You may have to change the logic board! ... Dishwashers

Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.


I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers

Kenmore ultra wash quiet guard dishwasher, the pots and pans and the normal wash button are blinking. The start and cancel and smart wash out tons have a faint light glowing. Thoughts? I tried the sequence of pressing heated dry, normal wash, heated dry, normal wash and that did nothing. I've flipped the breaker too. I was in process of taking it apart to clean filter, thinking that would help, but lost my manual and now I can't get that off to flea either:(. Sig


... Kenmore 24 in. 15689 Built-in Dishwasher

I'm working with a kitchenaid D/W model N0. KUDS01FKSS1: I repired a broken wire that shorted out near the main board, after repairing the wire the cycle selector board "light wash cycle" was not working, after the customer used the D/W the "clean light starting flashing 7 times then pauses repeately, after instaling the selector board, I entered the diagnoptics code all lights came on and then I cancelled, the D/W started working, when the cycle finish the light will come back and D/W will no


... KitchenAid Dishwashers

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

Dishwasher inoperative The lights that indicate the wash cycle are flashing along with the 6 hour delay light. I have tried to cancel the cycle but it does not work. I shut off the breaker to try and reset the operation and that does not work. The dishwasher will not work and I cannot reset or cancel the flashing operations. Kenmore Quite Guard 3 Model 587 15072200


... Kenmore 15522 Built-in Dishwasher

I have a new Frigidaire FDB1050RE diswasher. I ran it for the first time set on normal wash and pressing both the Hi-temp wash and heat dry button. This cycle is supposed to take a total of 89 minutes to complete including the drying cycle. After 89 minutes it was still in the wash cycle so I cancelled it to preserve sanity. In the instruction manual it states that the water temperature must be above 120°F. Our building's water heating unit is set at 110°F. Why there is a lower temperature


It should still work pretty well but you probably can't use the high temp wash because it will take too long for the dishwasher to heat up the water enough to satisfy the high temp washer thermostat. If the thermostat's calibrated closing temperature ... Frigidaire Dishwashers

When i push the start button,it doesn't light up and start. The normal cycle and the other cycles lights work but it won't start. If i push hi-temp wash and heated dry several times, all lights will come on but when i try to run it through a cycle, it won't start.


I would replace the key pad it sounds like since everything else works.. so you hit the normal wash and start the dishwasher sits there for a min or two and turns off.. Its not recognising the start button ... Dishwashers

I have a Kenmore Elite Ultra Wash HE. Model #66513122K701. Serial #FY0310281. Purchased New 1/31/09. It only works for a full wash cycle on on 1 hour wash. Super Wash and Normal wash both stop mid cycle and leave dishes sopping, dipping wet and with green light blinking. Been doing this almost its entire life...has ahd control panel replaced once under warranty...but if it is a factory defect...they probably just repaced it with another defective part...what to do? What should I do.


... Kenmore Dishwashers

Whirlpool Gold Quiet Partner IV Dishwasher, Model GU1500XTKT0, Serial number FL4104935, Type 575-0, during a Rinse Only cycle suddenly the cycle light began constantly blinking, which could not canceled or stopped nor placed into diagnostic cycle or other wash cycle. The repairman checked everything and decided problem was Electronic Control Module, which he replaced; blinking Rinse Only went off, but Normal Wash is now constantly blinking and repairman seemed confused and is wanting to repla


... Whirlpool Dishwashers

Frigidaire FDB520RHB Dishwashers : We bought this dishwasher about 3 months ago. Today I ran the washer before I left to do errands and when I returned, I believe the washer had finished its cycle. But about an hour later, I noticed it had started up on its own? It then proceeded to run for almost 3 hours before my husband canceled the cycle. We were kind of waiting to see if it would stop on its own, which is why we let it go so long. I think it usually takes about 1 1/2-2 hours to wash. Could


Try to run the dishwasher on a short cycle like rinse and see if it finishes the cycle.It is likely the heater or hot water temperature is not reaching the desired level and this could cause the extended wash cycle. Feel water temperature ins ... Dishwashers

GE GSD5320 seemed to finish all light wash cycles. Then it began to beep, with the NORMAL light blinking. I hit RESET, but none of the other buttons worked. I threw the circuit breaker for this appliance and waited an hour. I Turned the circuit breaker on but now I get the NORMAL light blinking, even when the door latch is not engaged. No buttons work.


... GE GSD5320DBB Dishwasher

My frigidaire dishwahser was set to run a normal wash cycle and heat dry. It never ran, the soap is still in the holder and the lock beneath the heat dry option is lit. I'm unable to cancel or select any other options. I cannot get the dishwasher to run. Do you have a solution? I have tried holding down a number of the buttons in different combonations but still can't get the light to go out or start a wash cycle.


Looks like a number of things are happening.\015\012\015\012It would be easier if you can provide the model no. of your frigidaire dishwasher.\015\012\015\012I am assuming you have turned the mains power off and on. ... Frigidaire Dishwashers

I tried pressing the normal wash heat dry, normal wash heat dry several times, yes it reset my washer, but after a few uses, sometimes it will only run 5 minutes, sometimes it will run the full cycle. Then the green light starts blinking again. HELP!!!


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Du1145xtpba quietpartner II starts then stops shortly into cycle and the normal wash light just blinks, if you hit cancel then both lights will flash when unplugging/reconnecting ribbon cable from control board it will complete 1 cycle and more often than not will do the same thing


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Cranky dishwasher I have to admit my wife's solution is the only one that works. Our ten-year-old Superba built-in usually starts a normal cycle part-way through, at the wash part, without filling or opening the dispenser door. Therefore the dishes come out with the soil now baked on. Closing the door, selecting normal and start results in a pump-out sound, or at least just the pump running to wash the dishes. The dishwasher ignores any cancel button push,and the light does not come on over t


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the s ... KitchenAid KUDS24SE Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1512 seconds