Having problems with your Whirlpool Dishwashers ?

Whirlpool gold piece of junk Model: GU2475XTVY Runs out of water within 10 minutes of starting. Brand new ran 2 times. I'm thinking its a faulty drain control valve? Thoughts?


Answers :

Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Whirlpool gold piece of junk Model: GU2475XTVY Runs out of water within 10 minutes of starting. Brand new ran 2 times. I'm thinking its a faulty drain control valve? Thoughts?


... Whirlpool Dishwashers

Dishwasher (Whirlpool Model DU930PWQ0) won't pump out. Problem occurred after door was opened during a cycle. Then the pump-out function ceased to work. Washer fills and pumps correctly during the wash cycle. Any suggestions? My guess is that the electronic control may be faulty and it is not opening the solenoid valve for the drain cycle. The other option I have thought of is that the solenoid valve may be faulty and is not responding to the signal from the controller. The dishwasher is n


... Whirlpool DU930 Built-in Dishwasher

Hobart Sr24h drain valve solenoid constantly energized thought the whole dish washing and rinse cycle. The drain valve/solenoid is new. Is there a control board timer setting for the drain valve?


See the wirin diagram for test and see how to test: ... Dishwashers

Maytag HDB8600AWW Dishwasher had been making noise (thought might be water valve, like previous DW), eventually stopped draining water, water now in bottom, I've let sit for couple weeks, looked inside, water was gone, I tried running again, it filled with water, but heard humming control panel noises for first time, then shuts itself off. Also, my handle needs replaced. Please let me know as soon as possible. Thanks in advance. David Weaver


Hi David\015\012\015\012The hum and all the noise that you have mentioned in your post states that the issue is with the pump and motor assembly. Please check the drain hose and try to clean the drain pump filter for any clogs, obstructions. Af ... Dishwashers

I have a Smeg DWD1SSE dishwasher, that has decided to start and stop on it's own during the wash cycle. We have to restart it at least three times during the 30 min short wash, and it very rarely gets to finish a whole cycle. I have stripped it down to make sure that there is no moisture on the main PCB behind the buttons, which there isn't. I think it looks as though the control board is faulty. If anyone can help or back my thoughts up, I would be very great full. Thanks.


... Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

My Whirlpool wdf530payw dishwasher is not draining. I ran the service diagnostics using the control panel, and the code that came back was Function code 8, and Error code 2 "Drain Motor Electrical Problem". The possible causes listed are: a. Loose Connection in drain motor circuit, and/or open drain motor winding. b. Open Fuse on control to drain motor c. Faulty drain motor drive circuit on the control When I hit the "Cancel/Drain" button there's an faint buzzing sound for about 2 minut


... Whirlpool Dishwasher. Front Control Dishwasher in White WDF530PAYW

Have a whirlpool gold dishwasher.The problem is that the clean lite on the control panel flashes not allowing the unit to work.I installed a new disposal and forgot to remove the plug for the dishwasher drain hose.When the flood happened I opened the door in order to stop the dishwasher.Now the unit will not work.The lite flashes 7 time ,then it pauses and flashes 7 times etc.Is there a reset procedure to run in order to get the unit to work or do I need to buy a new control panel?


HI,Can you please give the make and the model no. so that i can give you the manual.Waiting for your reply ... Dishwashers

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

One day the diswasher was working fine...the next time it turned it on it ran for about 3 min. then shut off and seemed to have no power. I checked the breaker...it was fine. A few days went by and all of a sudden the lights were blinking on the panel. So I pushed the cancel drain button. The water drained out and I then proceeded to load the dishwasher and turn it on again thinking it was just a fluke when it shut off earlier in the week. It did the same thing...ran for about 3 min and then shu


... Whirlpool GU2200XTSS Built-in Dishwasher

My Kenmore dishwasher leaked out through the door and into the kitchen. It appears it is not draining and once the water reaches a certain level, pushes out the door. It did this before and we thought maybe the drain was clogged, but couldn't see anything. Ran it again and was fine but has now done it again. Could this be the control module or the overfill control, or something else?


\012\012Hi,\012Here\012is a tip that I wrote that will help you with your dishwasher not\012draining problem...Dishwasher Problems - ... Kenmore Dishwashers

I have a Bosch dishwasher, model #SHU43C02UC/14, which has stopped working - no water enters the inside nor is there any drain cycle - just nothing. At the same time, I had to have the new control board put in as part of the Bosch recall. The tech comes out, puts in the new board - still nothing. He says something is wrong with the board even though the problem existed before the new board was installed. He takes everything back to his shop and tells me he's trying to contact Bosch tech support


... Bosch Dishwashers

Blowing fuse... We've replaced the overheating fuse located in the control board area about 5 times. It has just blown again after using the dishwaser one time--before it would go about a month before blowing the fuse. It seems to get about a few minutes away from completing the wash cycle and does not complete the draining process. Help!! We don't know what to do next--replacing the fuse is costing about $15 each time, before you know it we could have bought a new one! Thanks for the help. Ti


Tim, this blown fuse issue was pretty common on this model. Whirlpool, which made this model came out with a fuse kit that included a terminal and heavier guage wire to eliminate this problem. It just splices right into the control board, easy job. T ... Kenmore 17024 Built-in Dishwasher

Honda GC190 no start. Unit has been sitting for 2 years. Drained old gas, cleaned the carb. No go. New plug gapped to 0.030in. Still nothing. spark seems good. Cleaned the fuel strainer and there IS a bit of vacuum at the fuel pump when cranking. Poured a dab of gas into combustion chamber.. Still won't "talk to me" AT ALL. Removed valve cover and checked the valves.. within specs and nothing sticking or hanging up. Timing belt and cam looks good. Took a peak at the coil.. air gap in specs. 1ohm


... Karcher 2500 PSI Pressure Washer

GE Mod # GSD22360Z04WW will not drain water. I manually pushed the solenoid down and the pump and motor seemed to run. No water pumped out of the hose that was disconnected from the garbage disposer. I have discovered that the plug for the disposer was not taken out where the dishwasher hose attached. The dish washer stopped working after a new disposer was installed. I rotated the control knob and at no time did the solenoid for the pump operate. It went back to normal position after control kn


... Dishwashers

Hello, I had a problem with my Bosch dishwasher not washing properly. I have fixed burnt out wires, replaced the water inlet valve, AND tested with a new control module. Nothing is helping. When I start the cycle, it completes the initial drain and water does flow into the unit for about a minute, maybe a minute and a half. I can hear the clicking of cycle changes but it is not washing. Eventually it will drain the inch or so of water in the bottom, but it never washes. Any help???


Hi,\015\012\015\012Welcome to Fixya.\015\012\015\012Can you hear the wash motor humming ? I`ve got a "pdf" I can send you regarding this if you want to contact me at ... Bosch SHU9925UC Built-in Dishwasher

I have a Kitchen Aid KUDS03CTSS3 dishwasher. Dirty water is staying at the bottom and nothing comes out the drain hose during the entire cycle. The drain hose is looped above the kitchen P-trap, although for a time it wasn't. I use a wet vac to get the water out but there is still water below the fine filter. I thought if I could get the fine filter off, I could clean out the bottom as I think that it's full of crud down there that may be blocking things. I can't figure out how to get the l


Hi,Thanks for the follow up. I am glad it worked out for you. If I can Help in the future let me know. http://www.fixya.com/support/c64627-kitchen_aid ... KitchenAid 24 in. KUDP02FR Built-in Dishwasher

Our dishwasher is brand new and the first time we tried to use it, the water didn't drain, so I ran through the cancel instructions, and it's still not draining


Make sure there are no kinks in the drain hose. Remove the hose at the sink drain and make sure the barb fitting on the sink drain is open into the drain interior. Can you hear the pump run when it is supposed to? If all else fails, call the folks th ... KitchenAid 24 in. KUDP02CRBS Stainless Steel Built-in Dishwasher

By jleejr on Jul 20, 2010" " I have a Maytag Quietseries 300 dishwasher that I bought new in 2004. The buttons on the control panel will not respond. That is, no lights will display when I push the buttons. It has behaved like this in the past and after several weeks of not using it suddenly it will begin working normally again. However, I think this time it has stopped working permanently. The model number is MDBTT79AWW. What do you think could be wrong? I have tried flipping the circuit breake


HI. The actual culprit in this situation will be your control panel(Defective Touch-pad circuit board). The panel and touch pad assembly are integrated. They share the same space. There is a small ribbon cable on the rear of the control panel that li ... Maytag Dishwashers

First 2 weeks ago i put an electric control module into the upper section. what comes on is the green flashing light for clean. in checking connections i found the paper for trouble shouting. i did what they said to do. they said hit the time saver - high temp - time saver - high temp. from there all the lights went on & the wash cycle started and ran. then it just stopped & the green light for clean just flashes. the water is still in the bottom & won't drain.


The error indicates that the machine has taken too long to drain the water. Do the following.\015\012 \015\012\015\012Switch off the machine, unplug or disconnect the ma ... Kenmore 16874 Built-in Dishwasher

I have a Maytag Quietseries 300 dishwasher that I bought new in 2004. The buttons on the control panel will not respond. That is, no lights will display when I push the buttons. It has behaved like this in the past and after several weeks of not using it suddenly it will begin working normally again. However, I think this time it has stopped working permanently. The model number is MDBTT79AWW. What do you think could be wrong? I have tried flipping the circuit breaker to reset it but no c


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. It seems to be the ... Dishwashers

Have GE Dishwasher model GLD6700N20WW,unit has stopped draining! Took apart and pump was running when check, but no water coming out. Checked drain line and pulled apart pump housing, all clear. Thought maybe pump has a silinoid built inside of it and was stuck shut, so bought new pump and same thing, no water will go thru! Please help me? Is it control module, or turbitity sensor possibly?


... GE Profile PDW8600J Built-in Dishwasher

New SHE4AM16UC, professionally installed eight months ago. Worked fine with very light usage until now. Dishwasher starts normally but stops and signals "clean" after less than five minutes on any cycle. One inch of water in bottom that (I think) drains when a new cycle starts. Soap tablets are not ejected from compartment. Bosch authorized repairman says he now has two client dishwashers with identical symptoms and is asking Bosch support for ideas (he's changed pump, control unit, and float sw


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats.\015\012When the dishwasher doesn't sense a water t ... Bosch SHE4AM16UC 24 in. Built-in Dishwasher

Model # KUDSO1DLSS1 Kitchenais dishwasher - had a burnt electric smell coming from the area of the touch pad (not the vent). Did "some" research and decided to replace the control board - smell went away - ran 3-4 cycles over a few days and then - no lights - tried a new control board (thinking the old defective) - nothing - replaced the thermal fuse - nothing - what next????


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

We live in an apartment and our hot point dishwashers timing is all off and i thought if i could fix it myself, i'd love to do that instead of calling our manager, i will call him, but if its an easy fix i'd like to try it out.. it will just stop in mid cycle, and you have to manually more it a fraction of an inch to get it restarted, then at the end it doesnt fully drain, and the drying takes forever, so if i cant fix it, i'll ask for a new one..


It might need a new mechanical timer (sounds like the timer is sticking) installed and the parts will cost money... so you might want to go the route of the manager. The dial that you turn to set the dishwasher is part of the mechanical timer. Someti ... Dishwashers

My Whirlpool ADP 553 dishwasher starts and time switch goes through normally but nothing happens. The only thing is it does try and drain previous water. I suspect the inlet valve to be faulty thereby not letting water in. Could this be the fault


... Whirlpool 18 in. ADP530 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1733 seconds