Having problems with your Whirlpool Dishwashers ?

I have an ADP6000IX Whirlpool dishwasher which is comming up with a Fault code Err4. The manual indicates overfilled and possible cause "too much inlet water", however there is no water sitting in base of machine, and have unloaded all dishes and Err4 still comes up. I have switched unit on and off at wall but has not re-set. I have disconnected water pipe from tap and reconnected.Is there anything further I can do?


Answers :

Hi,

\015\012
\015\012You can solve this by cleaning and de-greasing the filter frame, basket and sensor Also there might be a low threshold for oils/greases/debris of any kind, so you have to rinse and load. By removing outflow tube (clean), cleaning and inspecting all interior parts you can fix this problem. A pump/impeller blockage may also cause "F4", so have some light gauge wire, tape the end so as not to scratch or snag, and jam it into the outflow opening in the well, poking vigorously at the impeller blades. Ten seconds later you can able to run a complete cycle of *pure clean* dishes without any problem.

\015\012
Thank you !!
Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an ADP6000IX Whirlpool dishwasher which is comming up with a Fault code Err4. The manual indicates overfilled and possible cause "too much inlet water", however there is no water sitting in base of machine, and have unloaded all dishes and Err4 still comes up. I have switched unit on and off at wall but has not re-set. I have disconnected water pipe from tap and reconnected.Is there anything further I can do?


Hi, \015\012\015\012You can solve this by cleaning and de-greasing the filter frame, basket and sensor Also there might be a low threshold for oils/greases/debris of any kind, so you have to rinse and load. By removing outflow tube ... Whirlpool Dishwashers

I have a GE dishwasher model GLDL560N10SS. I noticed a burning smell coming from it the other day and then realized that although I can hear water running into the dishwasher when I start it, it never actually runs in the sense that the water is pushed through the various outlets to wash the dishes. I'm assuming that it is because the unit is dry and the heating element is still coming on that it is causing a burning smell. If I open the unit and reset it, it pumps the water back out into the si


The problem sounds like it is in the water inlet selonoid. Pull off the bottom panel and this is the part that the main water line hooks to there is a selonoid and it has a plugg inconnection to it unplugg it and check for power when the unit is supp ... Dishwashers

We used our LG diswasher to clean our grill grates, which was a bad idea, because now the unit will not clean the dishes. We cleared the washer arms of debris, but the unit still is leaving the dishes on both racks dirty and is leaving the liquid soap dispensed into the unit undissolved on the door of the unit. There are no kinks in the water inlet, and water is getting into the unit, but the dishes are not getting cleaned.


Hi\015\012\015\012\015\012Thanks for using FixYa. Please make sure the dishes are loaded properly or\015\012dishwasher is not overloaded. Also check that the dishwasher is filling\015\012properly. It will fill with water up to ... LG LDF6810ST Stainless Steel Built-in Dishwasher

Kenmore 665.16762000 We were washing dishes the other night and my husband walked into the kitchen to find water pouring out of the "air gap" in the sink. Now we cant get the unit to come on. Ive tried some of the various combinations of button pushing to re-set, but so far still not operating. I am thinking it may be the "thermal fuse" due to some other questions here, but how can i confirm.... and the biggest question... how much is that gonna cost me to replace if i do it myself?


... Kenmore 16762 Dishwasher

Mod #: MDB6600AWB Ser #: 16505148CG No water comes out of spray arms, checked and cleaned filter-OK. Wash impeller is cracked where it slides onto the hexagon rod but it you take the filter flow plate off and put the impeller back on, when you put the unit on rinse only and quickly open the door you can see it is still turning and moving the water. The unit still fills and drains. it just does not have enough force with the impeller to force the water into the spray arms.


Hi,\015\012 \015\012Please check the bellow link regarding your query....\015\012 \015\012 ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

Dishes are still dirty. I have used every kind of dishwasher aide, half loaded it and dishes are still dirty, I let the water run until very hot before starting the washer. The washer says you don't have to rinse but I do and they still come out dirty. Also black nasty stuff comes up from my garbage disposer.


Suggest the problem may be a plumbing issue - likely substantially blocked drain system, so the dirty wash water cannot properly pump out but rather remains in the dishwasher.\015\012\015\012Suggest getting a plumber in to "snake" out you ... Dishwashers

It appears to finish it's cycle, as far as the dishes are clean - however there is clean water that has pooled on the bottom. you can hear the water fresh coming in - the pump comes on for a few minutes, drains some of the water and shuts off - the pump comes on again - drains some of the water and turns off. I turned the water going into the dishwater off - the pump ran for a few minutes - drained some of the water and then just sits there with the red power light on - there is still the same


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Bosch 23 in. SHU3302UC Built-in Dishwasher

We live on an island in the Caribbean and we have a LG dishwasher (model LDF 8812) that has worked fine for a year, but has recently stopped washing effectively. At first, the top part dishes were coming out still soiled from food. Now the bottom part dishes are coming out soiled as well. We checked both the Owner's Manual and the Service Manual and none of the troubleshooting suggestions appear to be relevant to our problem. The water here is very hard, and the water pressure is low and fluctua


You really need to replace the O ring . Could cause leaks and low wash pressure without it.You may also try running a solution of WHITE vinegar and water through the machine every six months as it helps desolve any lime scale (which is going to ... LG LDF8812 Stainless Steel Built-in Dishwasher

I have had a repairman come out and look at this and he says all the diagnostic test say everything is okay. My problem: my dishes come out dripping wet...like it hasnt dried anything. Sometimes dishes are still dirty. I don't think there is any heat getting to anything. I run the water in the sink beforehand to try to get the water hot. I used this dishwasher for 1-1/2 years with no problems and now I have this problem. What is going on?


I am having the same problem but do not see any posted solutions. Have you solved this problem? ... LG LDS4821ST Stainless Steel 24 in. Built-in Dishwasher

Whirlpool Dishwasher GU2548XTP- Dishes still dirty after it has run, especially the top rack. 5 (?) yrs old. Runs and grinds intermittently, no water seen under unit. Sometimes I add more water when it grinds, then it runs very quiet. Sometimes it doesn't seem to fill enough. Water supply good, inlet screen inspected not clogged. Not a lot of pressure shooting the water around the inside of the unit, as the detergent that bleeds through the slotted half of the detergent flip door isn't r


The inlet valve is OK, therefore the control board was not the problem. The impeller pump is noisy and inefficient, and must be replaced.Here is the part: ... Dishwashers

My Kitchen Aid KUDS01DJSS0 seems to have water going to the upper spray arm (I see water coming out of the unit just beneath the upper rack), but the pressure doesn't seem to be high enough to clean the upper rack. No evidence that water is coming out of the spray arm on the very top. Lower rack dishes seem to clean OK. I have already removed the whole upper spray arm assembly and inspected the flapper valves that the middle sprayer goes into. I suspect that it's not making good enough contac


... KitchenAid Dishwashers

2 weeks ago, I had a plumber come and put in a new garbage diposer and since then somewhat old/dirty water seems to be sitting at the bottom after all cycles are done. I calle dhim back and he says that there is no problem in the plumbing but more with the pump. I even use the wt/dry vac and removed water and ran it but still comes back with water at the bottom. also the dishes smell like soap. Help!!!


The plumber did not make an air gap in the dishwasher drain hose when he reattached it to the new disposal. Look under your sink, does the hose (attached to the disposal) go down and through the cabinet? If so, that is definitely the issue. Simple ... GE 24 in. Profile PDW7800 Built-in Dishwasher

My Whirlpool Gold Series 980 dishwater no longer fills up with enough water to drive the washing arms, so the dishes do not come out clean. I cleaned the filter on the water intake valve (which was really clogged) and it still did the same thing. Replaced the inlet valve and still no change. The water does not reach the level of the overfill float switch, so that’s not it. Its been working fine for 4-5 years, what else could it be? Thank you.


I hve provided u with all details .read it carefully .it has all the resolutions for all possibilities ... Whirlpool Dishwashers

I have a Frigidaire UC DW Model FDB250RHB2 The unit is not a year old. It is not getting dishes very clean. I read similar posts. I found that there is water coming from top nozzle but not a very impressive stream. It is weak enough that most of the water misses the funnel on top rack. Also not top or bottom arms spin. Last week when i would quick peek during wash cycle there seem to be water coming out of top arm's holes but no spin. We also are getting heavy white staining on glass ware


... Frigidaire FDB520RH Builtin Dishwasher

Kitchenaid dishwasher - small pieces of food are left on otherwise clean dishes. Water level comes to about 1 inch below heater coil. I ran it without dishes (or soap) and added about a quart of water so that level came to about 1/4 inch below heater and that's when I noticed food pieces on drain surfaces (nylon filter under bottom spray arm unit and circular plastic "trap" surrounding it). Spray arms holes are clear and water is hot.


It sounds as if you figured the solution out. The holes in the spray arm(s) get plugged by small debris, (tooth picks, seeds, bits of plastic like candy wrappers, etc) and the water does not reach the dishes to wash and rinse effective ... Dishwashers

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

MAYTAG MDBH979AWS DOES NOT SEEM TO FILL WITH WATER, AND HAS STOPPED CLEANING THE DISHES..My husband took everything apart and we cleaned each piece and put it back together , there was no indication that anything was clogged, and he was able to determine that water was coming in to the washer, but dishes are still dirty. There seems to be soap residue on the bottom of the tub. We also check to see if it was draining properly and that was fine also. Any other suggestions?


... GE Dishwashers

We have a newer bosch unit and it worked well in the beginning. Lately, we are having problems with dishes coming out not clean - bits of food still left on glasses and plates. Now we are scrubbing them clean before we put them in the dishwasher and some still come out with food bits on them. What is happening?


Check that the soap dispenser opens correctly ... Bosch SHE4AM16UC 24 in. Built-in Dishwasher

We have had this dishwasher for approximately 2 years. Dishes do not clean well. For example, I put a mixing bowl in that I just mixed brownie in--and the bowl did not come clean (simply a thick chocolate mix). Glasses do not come clean. They always have a fine residue on the outside (food). My husband just took the (blades) out that spin and dispense water and cleaned them. The water volume seems better now. Still, if I remember correctly, the dishwasher cost around $900. It definitely


Check if the water gets hot . \012\011check if motor spins enough to give pressure water on arms to clean dishes.\012\011clean the filter regulary . ... GE Profile PDW8480JSS Built-in Dishwasher

Dishlex Global 310 model. My dishwasher has water sitting on the bottom of it and it wont drain. I noticed it after I did a cycle of dirty dishes and the 'fast' light was flashing when I went to open it. Which shouldnt have been because it was on a normal wash. The water has been sitting at the bottom for 2 days now and still wont drain! I've taken out all the parts on the bottom which come out and cleaned them. Still no change however.


Just ran another cycle and it was fine ... Dishwashers

My KitchenAid dishwasher (model KUD101TJWH0) suddenly is making noise from the motor area while inputing water into the unit, whether in the rinse or washing cycles but makes no noise in the draining cycles. I have pulled the unit out while still connected, cleaned any debris from the filter screen below the lower water spokes and can hear the noise very plainly by the motor but I know how sound can travel with the piping. Is the sound only coming from the electric drive motor attached to the


... KitchenAid Dishwashers

I have a Miele G570 dishwasher and the spinners don't appear to be turning properly. I have removed and cleaned the incoming water strainer, but still no better. The water supply pressure is the same as always. The unit goes through it's complete cycle but the dishes are still not clean. Can you help please?


Run a nice long hot "Pots and Pans" cycle every now and then.Try calling the Miele Appliance Hotline 1-800-999-1360 when your in front of the machine. ... Miele Dishwashers

LG model LDS5811WW/02 has never cleaned the dishes since first installation. Put clean dishes in and they will come out dirty too! Have tried all dishwasher soap types and brands and drying agents. Always scrape and rinse dishes prior to loading. Dishes loaded various ways but problem remains. Repairman says unit is working fine. Also never dries dishes completely. Often leaves soap dispenser completely or partially filled. We are on a farm and have hard water but we have a softener/iron remover


If the soap/detergent isn't completely rinsing out of dispenser, it sounds like water isn't directed the top spray-arm. possible a defective vario motor; as it directs water to the water channel that supplies water to the middle and upper spray arms. ... LG LDF8812 Stainless Steel Built-in Dishwasher

Dish-washer My dishwasher is not draining all of the water out of the dishwasher after it washes. I got someone to look at the drain pipes and he cleaned out the stuff and they still will not drain all of the water. I would like to know what I could do to get all of the water out of the dishwasher so that the water will come out of the bottom of the machine. Wanda


The problem is most likely that the pump empeller had been damage by pieces from a broken dish or a small piece of siverware. The only way to fix this is to take the dishwasher apart and replace the empeller. If you choose to do this yourself, you sh ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My Kenmore Elite dishwasher doesn't wash dishes properly. I think that it is not getting enough water in the machine. It only allows about an inch of water to get into machine and then starts. I do not think that there is enough water to spin wash arms. I have 40 PSI coming into the house. I am on well water and found debris in the intake orfice. I did my best to flush. Could it still be bad?


I am having the same problem with my brand new Dishwasher. ... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1870 seconds