Having problems with your Whirlpool Dishwashers ?

Fails to go into rinse cycle. When Rinse Button is depressed, a number "2" is displayed.


Answers :

Hi


Thanks for using FixYa. From what you have described it seems to be an issue with the timer that has gone bad, they don’t often fail but if everything else is working fine then it is the Timer that has gone bad and needs to be replaced. If the timer appears to be working fine then the issue is with the heating element which is not heating up water and as the water is unable to reach a higher temperature the unit stops at heating cycle i.e. rinse... To resolve this issue you’ll have to repair the heating system problem. Please do accept the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee
Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Fails to go into rinse cycle. When Rinse Button is depressed, a number "2" is displayed.


HiThanks for using FixYa. From what you have described it seems to be an issue with the timer that has gone bad, they don’t often fail but if everything else is working fine then it is the Timer ... Whirlpool Dishwashers

I have a Kenmore Ultra wash 665 15895 dishwasher. It will not run any cycles. Symptoms: When I first close the door, the "Quick Rinse" light is on and the number 18 is displayed. When I push any button, the "Quick Rinse" light flashes continuously. If I touch any other button, both the "Quick Rinse" and "Pots and Pans" lights flash continuously. No matter what buttons I press, the behavior is the same. I've tried turning the power off and on, same behavior. The only button that doe


\015\012HiThis may be an issue with heater circuit, door switch or wash pump. Press and hold the heated dry/air dry button for 15 seconds....After, 5 minutes check if you are still getting the same error. If yes, ... Kenmore 15899 Built-in Dishwasher

My Maytag dishwasher model MDB600AWB, serial 18721619CN Quiet Series 300 will light up on the panel except for NORMAL WASH and START. It will not run. All other buttons work. It displayed the number 9 and the RINSE ONLY light came on after we got off the phone with Maytag. Initially nothing would light at all. We changed the fuse (it is NOT on a breaker) and it again didn't light. A few minutes later it did light the above mentioned buttons.


... Maytag Dishwashers

Kenmore 665.15912001 DISHWASHER RUNS BUT DISPLAYS ERROR MESSAGE Instead of displaying the number of minutes in the cycle when I push the cycle selector button and then the start button, it starts as soon as I push the cycle selector, without waiting for me to push start; meanwhile, it displays "_J" instead of the number of minutes in the cycle. It washes the dishes but not well, lots of food debris. Some people in this forum have described running a diagnostic on this machine; how do you do that


... Kenmore 15912 Built-in Dishwasher

I have a Frigidaire Model Number GLD4355RFS1 Serial Number TH80493988 Dishwasher. It quit working when the Rinsing Agent Low light came on. We filled the rinding Agen dispenser with hopes that it would come back on. The Rinsing Agent Low light went off but the unit never came back to life. When the room is totally dark, you can just barely see the lights in the LED display and other lights. It will not come back on. I tied turing the power off and the "PH" alert is displayed in t


... Frigidaire Dishwashers

Lights on Dishwasher light up but nothing happens. When I reset power it lights up the high temp and sanitize button light up and LED displays PF. After I open the door they stop flashing. the far left five buttons light up when I push them and a corresponding number displays on the LED screen. the only lights that do not come on are the Delay button and power button. Don't know if they are working or just don't light up. No matter what lights up the unit does not turn on....:( ? help can't fin


Pf is power failure\015\012 your loosing voltage to the unit \015\012it may just be the door switch or it could be in the control\015\012 try starting the unit but keep your hand on the unit pushing the door in place,, its not a g ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

Kenmore dishwasher 16934 will not start up for me. I can push any button to set the cycle(pots & pans, china gentle, quick rinse, normal wash) and the time shows up in the display, but when I push the start, two red horizontal lines appear in the time remaining display. Cannot get the machine to start anything. All cycle buttons give me some kind of time remaining display but as I said, it ends up with 2 red lines. Thanks in advance. Mark


... Kenmore 24 in. 16934 Built-in Dishwasher

I have a KitchenAid KUDS01IJ Dishwasher. The Rinse Only light is blinking and cannot be turned off or switched to another setting. Multiple presses of the Cancel/Drain button will sometimes have the display show '2' or '---'. A few minutes later the display goes blank and the Rinse Only light starts to blink.


... KitchenAid KUDS01IJ - Multiple Color Dishwasher

My bosch she43f won't turn on. It has power, can turn the power button on and off, but the other 4 buttons won't release, it has the regular wash and rinse and hold are depressed. No light comes on above them. Can't push the other buttons.


... Bosch Dishwashers

I have a kenmore dishwasher model number 665.17332400 the air dry button flashes on and off when u hit start button do run washer the quick rinse button flashes as well and washer will not run. What is the problem and how do I fix it?


... Dishwashers

I have a dishwasher model number FGHD2433KWI...I have no display showing but I do have power. It is not coming on and am wondering if the button to start is not working properly. Needing to know how t


... Frigidaire Dishwashers

"sensor ok" - display is not lighting up at beginning of wash cycle - then "sanitation rinse" icon not displayed at end of cycle even though sanitize button was selected before start of cycle


... Bosch SHX98M09UC Integra 800 Series Dishwasher w/Display

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. My buttons on top are Accusense, pots&pans, normal, light, glass express, rinse only Soak and scour Hi temp wash


I think I just responded to this problem. Please accept both if you are happy with the solution. ... Dishwashers

I have a Maytag Quiet Series 300 dishwasher model number MDBH955AWW. When I press the wash cycle button it starts and then automatically jumps to the rinse cycle. After going thru the rinse cycle for a couple of minutes, it shuts off. After that,I can push the wash cycle agin and it works. Any idea what could be wrong?


HI. This will be a basic logic chip fault. It could possibly be solved by simply preforming a hard reset. You can do this by shutting down the power to the unit for five minutes. This shutdown will force the logic sector of your electronic control bo ... Maytag 24 in. MDB9750AW Dishwasher

When switch on button in on position, display showing 180 min wash time and saying machine requires salt and rinse aid, but machine was topped up 2 days earlier. Also sounds as though the pump is constantly pumping. All display lights on front of door went out.


... Siemens SE24A230 ExtraKlasse Built-In Dishwasher

Hi, ^The GE dishwasher (PDW788000SS) will not fill in either "rinse only" or "normal wash" modes. The control panel lights up with all functions. After selecting rinse only or normal wash and pressing/holding the start/reset button down for several seconds to reset the unit the drain pump comes on for approx 90 seconds as advertised. Checked the float switch and there is no continuity in any position of the little switch arm and the switch arm has no spring on it. Seems like this is a faile


Hello there:If there's no water entering your dishwasher in these cycles as you described, check these:\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012 ... GE 24 in. Profile PDW7880G Built-in Dishwasher

I have a whirlpool quiet partner i dishwasher (model DU1055XTSQ2) that has suddenly stopped working. Control panel has partial functionality. All of the buttons on the control panel have a green LED feedback light when depressed. None of them provide LED feedback anymore except the Hi-Temp Wash, Sani-Rinse, and Heated Dry buttons. So there is power to the dishwasher. Any ideas? Please help Scott


The control board has failed.CLICK HERE to see the parts breakdown. ... Whirlpool DU1055XTSQ Built-in Dishwasher

I have a Maytag Quietseries 300 dishwasher that I bought new in 2004. The buttons on the control panel will not respond. That is, no lights will display when I push the buttons. It has behaved like this in the past and after several weeks of not using it suddenly it will begin working normally again. However, I think this time it has stopped working permanently. The model number is MDBTT79AWW. What do you think could be wrong? I have tried flipping the circuit breaker to reset it but no c


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. It seems to be the ... Dishwashers

Hi , i have westinghouse dishwasher model SB915SJ. when i put it to wash on eco normal, it stops a after about 20 minutes and i have to press the program button to start it working again. it's currently running now but it stops about every 4 minutes and the numebr 20 appears in the display screen. if i push the program button it will rung for another 4 minutes then stop, start beeping and the number 20 appears. how can i fix this?


Www.westinghouse.co.nz/...westinghouse/.../NZ_WH_Dishwashers_May06.pdf \015\012\015\012\015\012\015\012Above is your user manual, and below is your service and repair manual.\015\012 ... Westinghouse Dishwashers

1999 Kitchenaid KUDs25shwh1 Anitbacterial/Light China/Sani Rinse buttons are not working. Have had this problem in the past and resolved it by pressing a sequence of buttons. (SuperWash/EnergyDry/Superwash/Energy Dry is not the sequence. I originally got the sequence from Kitchenaid. I was able to google it once by the model number and found it once for another model, so I now it exists. Does anyone know of a sequence other than SuperWash/EnergyDry/Superwash/Energy Dry for resetting Kitchen


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Have a NEFF S5453XOGB built in dishwasher - put it on last night and came down this morning and nothing has been cleaned and I have 2 red lines in the time display. HAve tried resetting by holding the 2 buttons down and switching on - it shows the number 23 - as sson as I let go the lights continue to flash and the number 1 appears. I am resetting it correctly?


... Neff 24 in. S5453X1 Built-in Dishwasher

By jleejr on Jul 20, 2010" " I have a Maytag Quietseries 300 dishwasher that I bought new in 2004. The buttons on the control panel will not respond. That is, no lights will display when I push the buttons. It has behaved like this in the past and after several weeks of not using it suddenly it will begin working normally again. However, I think this time it has stopped working permanently. The model number is MDBTT79AWW. What do you think could be wrong? I have tried flipping the circuit breake


HI. The actual culprit in this situation will be your control panel(Defective Touch-pad circuit board). The panel and touch pad assembly are integrated. They share the same space. There is a small ribbon cable on the rear of the control panel that li ... Maytag Dishwashers

I have a LG intello dishwasher 2050SH Turned it on yesterday and did a rinse. This was the first use for 4 months in our second home. It was very cold. The rinse stopped some way through and an error message displayed (cannot remember). Tried to run again and now the dsiplay is locked. It turns on with usual sound, but none of the buttons work. They make a noise when pressed but nothing on the dsipay changes. I suspect that the outlet was frozen and that I should not have tried again - too im


Hi\015\012\015\012To\015\012unlock the lock in your LG Dishwasher, with the door open press the SPRAY &\015\012RINSE buttons simultaneously for 15 seconds. Hope this helps...please post back fo ... Dishwashers

No Water Coming Into SHU43C05UC/12 Bosch Dishwasher: We have a Bosch Dishwasher, model number SHU43C05UC/12. It has been working for more than 4 years, but yesterday I notice that although I hear a motor sound, there is no water in the dishwasher. The LED display on the panel seems to be working all right. I ran a diagnostic pressing and holding Power Scrub and regular wash button then pressing the on/off button. Got C1 at start then P0 and the Regular wash and Quick wash flashing on/off. How c


... Dishwashers

Candy dishwasher (CDI 1012/2-80) On/off button is stuck in the depressed position. No lights displayed in Programme Indicator Lights on control panel. Programme key not responding. No apparent sign of life. Fuse has been checked and changed on the wall.


... Candy Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1108 seconds