Having problems with your Whirlpool Dishwashers ?

I had a black out and the dishwasher was running at the time. The dishwasher emptied out all over the floor. when the power came back on the dishwasher was flashing an error code 4. I rang Whirlpool for assistance and they said it was over full but it was totally empty. We turned the dishwasher off at the wall hoping it would reset but it is still saying error code 4. Can you suggest something else we can do?


Answers :

The trouble looks to be little confusing. Whenever the power fails
during mid cycle this happens. Try running the balance cycle.

Since you say the water is fully drained, try adding water manually to
the wash chamber to certain level ( not to over flow ). Give a try!

There should be a master reset for which, you are requested to check
the user manual
Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I had a black out and the dishwasher was running at the time. The dishwasher emptied out all over the floor. when the power came back on the dishwasher was flashing an error code 4. I rang Whirlpool for assistance and they said it was over full but it was totally empty. We turned the dishwasher off at the wall hoping it would reset but it is still saying error code 4. Can you suggest something else we can do?


The trouble looks to be little confusing. Whenever the power failsduring mid cycle this happens. Try running the balance cycle. Since you say the water is fully drained, try adding water manually tothe wash chamber to certain ... Whirlpool Dishwashers

Our dishwasher beeps twice when the start button is pressed but then doesn't do anything and there is no other noise from anywhere (eg, motor/pump). There are no error codes displayed and the display appears normal (ie lights up and shows time for program completion etc). When the problem first occurred the machine was full of dirty water. We have turned the dishwasher off and on at the wall, checked/cleaned all filters, drained the dirty water and still nothing happens (it doesn't even fill


... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

Hi My Fisher and Paykel Soft Touch dishwasher on a daily basis shows the error code F5 and beeps until I pull it out from the wall and turn it off and on again. How can I fix this?


There is no f5 fault in any of the soft touch f7p dishwashers, sure its not something else whats the model no , i fix f&p for a living ... Dishwashers

Hello everybody, I hope that you gona a give me some tips for repairing my dishwasher mashine. A few days ago, the error F2 appears on my dishwasher machine (Baucknecht GSI 5894) I checked the pump for the waste water is ok. the tap water is not taking in,I checked the hoses they are ok as well I turned off and on and same time pressed the button reset and choosing the programm on the dishwasher few seconds trying to start and again apperas F2 . Hopefully someone can help me. Best regard


Possible the inlet valve has given up and is not allowing water in.\012Also possible there is a slight leak enough to shut the water off (safety feature) - Check underneath for a float mechanism and any water there. ... Bauknecht Dishwashers

I have the "rinse" error code on my kitchenaid double drawer dishwasher kudd01dppa1. I've turned off the power, then it worked for one load and the code reappeared on both drawers again. What should be a next step? it says in the manual that the "rinse" error code means that something happened to the flood switch...? Can this be fixed without calling out the kitchenaid technicians? thanks


... KitchenAid 23 in. KUDD01DPPA Stainless Steel Dishwasher

Intermittent problem with error code E 01, which tells me there is a leak. However, I have turned the dishwasher on its side and back and am certain that the pan is empty. Indicates a false error code or sensor. How do I fix that or disable it?


... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers

I have a DWI 612C Smeg dishwasher I have an error code of the 2 right hand LED's flashing Have tried to reset the programmer (turn off, on then press program 4 times in 2 secs, wait 15 secs and turn off) This enables me to select a programme, but when the programme starts, after five mins it beeps and carries on making the draining pump noise and the programme never starts When I turn it off and back on I get the far 2 red lights flashing again Have looked for signs of blockages and can


... Smeg 24 in. DWI612 Built-in Dishwasher

Fisher dishwasher error code F1 after cleaning the dishwasher ......hope ya can help ....steve


How do you remove the drawer? ... Dishwashers

Hi There, I have a F&P 918td dishwasher which has stopped working. Whenever I press any of the buttons I get 5 very quick beeps and then nothing - no error message, nothing the display is blank. If I turn it off at the wall and then back on again the display briefly shows two characters that do not show up in the manual as valid errors. Any ideas anyone?


Sounds like a fried board. ... Dishwashers

I recently had the e4 error code on my new world dw60 dishwasher. I have since opened it up and replaced the heater element, which appears to have resolved that issue. However, in the process of doing this I incorrectly installed the flood switch back into place, meaning that it was in its closed position (i.e. the position it would be when activated by a flooded base) when I went to turn the dishwasher back on. I have since opened it back up and correctly installed the flood switch, but I ca


... Stoves 27 in. DW60 Built-in Dishwasher

My Samsung dmt300 had an leak on the outside hose with water coming out every where. I shut off water and fixed the leak. When I turned on the dishwasher a blinking heavy lite button came on. This error code means leakage How do I reset the sensor. The dishwasher worked fine before the outside leak .Please help, I don't want to call a repair person!


... Dishwashers

I am renting and have a heller dishwasher HDW12ISS. E4 error code is on the screen and is beeping when ever i turn on. how do i fix this?? filter is clean in the dishwasher.


... Dishwashers

When I turn on my Turbo dishwasher it goes for about 3 mins then comes up with an E1 error; I've tried resetting the machine, but then the display shows "1h" and "05" flashing three times each. The machine starts and error code above happens again.


... Dishwashers

Towards end of dishwashing cycle error code comes up and consitently beeps, can not turn off by machine buttons or reset. We have to reset by power plug. Water is left in bottom of macine, dishwashing powder is left on most things. Rinse button then works, it then drains the machine no problem. So I dont think it is the pump.


No response ... Dishwashers

Dacor Dishwasher error code F8


... Dacor Epicure IDW30 Built-in Dishwasher

F&P dishwasher DW60CDX1 (5yrs old) which will drain then fill but will not start the wash cycle. No error codes just a humming sound, possibly faint electrical burning smell (turned off quickly in


... Fisher and Paykel Dishwashers

We have a 3 mo. old bosch dishwasher (she6af06uc), that's giving me error code 24, turning off and not draining. Yes, there's a warranty, but if I can fix it quicker, that would be great.


The code you are getting is a drain pump issue.use a wet dry shop vac attach it to the end of the drain hose to remove the water.then check your drain pump for any kind of obsrtutions.\015\012Also make sure the if it attached to a garbage dispo ... Bosch 24 in. SHX99A15UC Stainless Steel Dishwasher

Fagor dishwasher with fault code F4 and pump keeps running even main switch turned off. Won't stop before totally unplugged.


... Dishwashers

Fisher & Paykel DW60CDX2 spray arms do not start rotating after turning dishwasher on. Nothing stuck and I can rotate it freely with my hand. No error code comes up.


... Fisher and Paykel Dishwashers

I hav an Electrolux EIDW6105GS1 dishwasher that has the error code 01 'Leak Detector' is ther anyway to reset this? I have turned off the breaker for over an hour and that did not work.


... Electrolux Dishwashers

Hello, I am having problems witha kenwood dishwasher, it just isn't cleaning anything. It seems to be going through the cycles and sometimes the dishes particularly in the top rack are a bit cleaner but in general they are uncleaned. There are no error codes. I wondered if the arms for some reason weren't turning correctly as some of the dishes were clean but this is inconsistent. I have tried changing detergents, adding more salt and rinse aid but it still isn't working, can you help?


... Kenwood Dishwashers

Installed new frigidaire 4300 series dishwasher. turn it on and get error code "Er" and "uo". What's the deal?


... Frigidaire Dishwashers

The dishwasher won't turn on. It sings its little song and flashes error code that looks like an upside down and backwards F and an E. what's it telling me?


Those are not common error codes. Try disconnecting the power to the unit by turning off the breaker in your panel box and then reenergize and see what happens. ... Dishwashers

My lg dishwasher LD-14AW2 is not starting. It turns on and displays the time but when I click on anything it double bings and nothing happens. I have cleaned out the filters and my husband has removed the drain hose from the s band and it was all clean. the display looks normal...no error code. Do you have any idea what the problem could be?


Tunr power off 20 min then back on see if this helps ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2471 seconds