Having problems with your Whirlpool Dishwashers ?

Soap dispenser will not open. I replaced the wax motor and still nothing. Is there a way to verify if the control board is bad?


Answers :

Verify that the bottom tray is not in backwards. There is a space on one side only, usually, and this keeps the door forced shut.
Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Soap dispenser will not open. I replaced the wax motor and still nothing. Is there a way to verify if the control board is bad?


Verify that the bottom tray is not in backwards. There is a space on one side only, usually, and this keeps the door forced shut. ... Whirlpool Dishwashers

I have a KitchenAid dishwasher model KUDC10IXWH1 that has no control power. I have already verified that there is 120V at the control board. The unit kept the lights on after the cleaning cycle was done and I couldn't shut them off. I reset the electrical breaker and now nothing works, but the board has power. Please give any advice you might have. I was thinking of replacing the board, but I'm not sure if it is the board or the front control panel. Any way to tell?


... KitchenAid 24-in Built-In Dishwasher White ENERGY STAR KUDC10IXWH

My Bosch SHX46A06UC/42 stopped working today. I can hear the drain pump constantly pulsing about once every second. I checked the control board and found a relay contacted burned. I re-soldered the relay so it now has a good connection, however the drain pump still just pulses. How do I verify if the drain pump is bad or if the relay failed, or yet another problem?


... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

I have a Bosch dishwasher, model #SHU43C02UC/14, which has stopped working - no water enters the inside nor is there any drain cycle - just nothing. At the same time, I had to have the new control board put in as part of the Bosch recall. The tech comes out, puts in the new board - still nothing. He says something is wrong with the board even though the problem existed before the new board was installed. He takes everything back to his shop and tells me he's trying to contact Bosch tech support


... Bosch Dishwashers

I have a whirlpool dishwasher thats a quiet partner 2. the cancel drain light keeps blinking and nothing else is happening. i try to unlock it and then the normal light starts blinking also and still nothing happens. i called a local repair shop and they said i need to change the control board so i did and its still does the same thing. can you give me an idea of where i need to start to fix my problem?


Can you here the pump running or check to make sure there is no water in the base... ... Dishwashers

My Amana ADB1500AWB3 has power all the way to the control board but the panel lights do not illuminate and the dishwasher won't run. I suspect the control board is bad, but I hate to spend the $100+ to replace it only to find out it was something else. Any advice?


... Amana 24 in. ADB1500AW Built-in Dishwasher

My power button cover broke on the dishwasher and I figured out the part number I needed, but when I put it back together I got the wires crossed on the board and door switch. Now the control lights up , but the dishwasher will not run a cycle. THe question is does the plug on the door switch have to be a certain way, because there are three wires and you can connect the plug both ways. I did turn the plug, but it still does not run. Did I break the switch? Bosch SHU9956uc/14


The wires do have to be a certain way on the door. Otherwise a door open can tell the board that's it shut and vice versa. The easiest way to do it, is test the switch with an ohmmeter, place the meter on the switch, push button in and see if the rea ... Bosch SHU9956 Built-in Dishwasher

I have a Kenmore Elite 665 Dishwasher. The front control display has been partially working but the dishwasher still worked. Today when we tried to start it it will do nothing & it is getting the correct power. Would this be the control circuit board or something else?


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a KitchenAid Dishwasher KUDIO1iLBS2 and none of the lights come on and if I press any of the buttons nothing happens. The unit is getting power to it as I shocked myself. I did ordered and replaced the control board and still nothing is happening. Any suggestions or ideas? Is there a reset button or is there a possible fuse that is out that would make the lights not come on? Please help.


... KitchenAid Dishwashers

My ge profile dishwasher is making a buzzing sound from the pezio buzzer on the control board. This started after a power outage. I verified power and ordered a new control module. After installing the new part it still buzzes and does not function.


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Hi silverdragon, re the dishlex 302 not heating or drying Have replaced heating element but unfortunately still cold. If the control panel has not shorted which it hadn't before, do you have any suggestions. My hubby would rather wait before buying a new dishwasher, but I don't want to throw good money after bad. Is there anyone you can suggest who would be able to check out the circuit board to see if i have missed anything.


Hi\015\012\015\012Check the two thermostats located at the inside bottom front\015\012panel of the dishwasher, if any one of them goes bad it won't heat. Hope this\015\012helps...please post back for further assistance.\015\012\015\ ... Dishwashers

Gu2400xtps7 "normal" green light keeps flashing. Unit will not respond to anything. tried cutting the power off...still nothing. Can this be reset by pushing a combination of buttons? How do I know if it's the "Console Assembly" or the "Electronic Control Board"? I want to order the correct part. Thank you!!!!!!!!!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Maytag mdbtt79 high current error but have checked everything broken impeller was replaced but still getting error is there a way to reset the control board have checked with ampmeter and current is with in specs


You may need to check connections on the control board,it may be receiving a "glitch"code from poor connections ... Dishwashers

The Bosch plastic push button (AP2804452) has broken on my SHU9950 dishwasher. The switch itself is still good. I have removed the broken pieces of the bad button from the unit and am now depressing the switch without the button. When I get the new push button, what is the proper way to remove the control panel cover to put the new button in place? Thanks!


... Dishwashers

Kenmore dishwasher I ran my dishwasher last night and this morning it was still on in the drying cycle had melted several things. Any ideas what is bad - control board or timer?


Could be eithe depending on which one u have model and make helps ... Bosch 24 in. SHU43 Built-in Dishwasher

Maytag MDBTT79AWW dishwasher fills and nothing else. Once filled you hear a click, followed by a humming sound for 3-5 seconds, then silence. This will happen two or three more times, and then unit will shut off. Motor doesn't start. Repairman says he thinks control board is bad, but he sounds like he is guessing. I performed a field service test , which indicated a fault in the high current motor circuit. Unit is seven years old. Don't know whether to attempt repair, or replace.


That sounds like the motor trying to start but being jammed it is shutting off via an internal breaker. Check for something in the bootom of dishwasher that might have gotten down there that could do this. You might have to take the sprayer off and s ... Dishwashers

I HAVE A KITCHENAID DISHWASHER, MODEL NUMBER KUDM03FTSS3. I HAVE REPLACED THE CONTROL BOARD AND TOUCHPAD AND STILL GET NOTHING ON THE TOUCHPAD


Hello,\015\012\015\012You replaced the electronic control board/timer as well as the touchpad/user interface, but what about the overload/thermal fuse ? I`ll also assume you`ve checked the breaker as well as power (120vac ) to the unit. ... Dishwashers

My Kitchenaid dishwasher (model KUDS02SRSS0) keeps burning out my dispenser. First I replaced the dispenser, then I replaced the control board and dispenser, it worked for two weeks and now I have a melted solenoid again in my dispenser. I've measured voltage to the solenoid and it is getting 110V through the entire diagnostic cycle. This is wrong. It should only get power at some point during the cycle to open the dispenser. It appears the control board has failed again and in the same wa


HI. The relay that controls the voltage and timed release command, via logic chip, is indeed damaged(stuck on). This is a common theme with this particular design. The original control board was recently replaced with a substitution model ... KitchenAid 24 in. KUDP01DLBS Free-standing Dishwasher

Model # KUDSO1DLSS1 Kitchenais dishwasher - had a burnt electric smell coming from the area of the touch pad (not the vent). Did "some" research and decided to replace the control board - smell went away - ran 3-4 cycles over a few days and then - no lights - tried a new control board (thinking the old defective) - nothing - replaced the thermal fuse - nothing - what next????


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Bosch dishwasher detergent dispenser will not open during cycle after I changed a burnt out control module. so changed the solenoid, still no joy so changed the dispenser? still will not open during cycle. Should the control module be programmed?


... Bosch 24 in. SHU43 Built-in Dishwasher

Maytag model MDB5600AWB replaced faulty control panel started and lit up like it is supposed to do started wash with glisten cleaner and when I tried to cancel drying cycle panel or board would not respond, waited till unit was finished and control panel blinked and went dark , bad control board?


... Maytag 24 in. MDB5651A Built-in Dishwasher

Replaced control board on my Kenmore dishwaser 665.13122k703. Still have problem with blinking lights and maybe one minute of operation, then stops and normal wash light blinking again. Cancle drain button only one that works, then normal wash blinks. I have another control board, however before I install it, should I be looking eleswhere the the problem ?


... Dishwashers

I have an 8 year-old Kenmore 665.16912 dishwasher. Worked fine until two days ago. Then it stopped working altogether: nothing lights up on the front panel. I have checked the 120 in the electrical box, the door switch is working, the thermal fuse is working and there is 120 volts at the white and black connections to the timer control board. I bought a new timer control board for $120 and that did not fix the problem. What else could be causing the unit to completely stop working?


If all are really good then the only thing it con be is the display (8269205) $25.00 part, if it's bad dishwasher wont run ... Kenmore 16912 Built-in Dishwasher

Maytag MDB6600AWW Unit is approx 3 years old it was finishing a load and stopped part way through sticking on heated dry. I don't know if it was there in the cycle or if the diagnostics on the board sent the message there. The light now will not shut off or move from the heated dry. I have disconnected 120 volts, removed the panel to check wiring, removed board and reassembled nothing resets the heated dry light and nothing works. I have gone through manual function test, sales floor demo test,


Have you tried pushing heated wash, heated dry, heated wash then heated dry? Sometimes this will reset it. ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

We had a power surge and the guy who looked at it said my control board was fried. It looked to me like a plug in item easily replaced by anybody with a screwdriver to take the door panel off, however in trying to find the part nothing is called "control board". What is it>


Its called a pcb call ge and order a new pcb for the make and model ... GE 24 in. Profile PDW7800 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1222 seconds