Having problems with your Whirlpool Dishwashers ?

My dishwasher dial/knob seems to be stuck,ie not moving to do a wash cycle but it will take in water and if i manually turn dial it will release water.whirlpool mod no. dw621/1 bw series 600


Answers :

Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishwasher dial/knob seems to be stuck,ie not moving to do a wash cycle but it will take in water and if i manually turn dial it will release water.whirlpool mod no. dw621/1 bw series 600


... Whirlpool Dishwashers

Dishwasher when turned to usual dial number hums enthusiastically but does nothing, no water, dial does not advance. If dial is advanced manually, some cold water is produced; dishwasher tablet is released but not dissovlved. All rotor arms and water intake areas are free of obstacles and blockage (as far as we can see). Any ideas?


Removed the filter and shopping for a replacement. An "in progress" report - not completely solved yet. ... Dishwashers

I have a mod. GSD2200G00WW . It has low water level and not enough pressure to turn the spray arm. When first starting i see water coming in but not enough. I added water in manually with a container and turned on and the spray arm rotated fine. I closed the door and turned back on and the water drained out of it instantly back to a low level. What now?


... GE Dishwashers

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

Our Miele DW just keeps going through cycles constantly and will not shut off on its own. It has gone all day. When we turned the dial manually to "OFF", the water keeps filling until it overflows the machine onto the floor. So far, our only option has been to turn the machine back on and let it keep running. Any suggestions?


Hi,\015\012\015\012sounds like a faulty electronic unit as i have seen this before where the unit continously fills with water. \015\012you will probably need a service call to repair the unit unless you are happy to fix it yourselv ... Miele 24 in. G865 Built-in Dishwasher

I have a frigidaire dishwasher. the manual says it is 200,500,700,800 series about 7 years old. yesterday when turned on everything seemed normal except that no water was dispensed. The float seems to work ok. Since we have neer had a problem before with it, it seems puzzling. Is ther an easy way to pinpoint the problem?


... Frigidaire 24 in. FDBB840DC Stainless Steel Built-in Dishwasher

New SAMSUNG DMT300 series Leakage Error upon 1st run cycle unit it is disconected and water supply has been turned off as per instruction manual.


I seem to be having this same problem... Did you ever find the solution? ... Samsung 24 in. DB5710DT Stainless Steel Built-in Dishwasher

I have a Kenmore dishwasher (model 363.14478791). I hadn't used the dishwasher in a month. I turned on the dishwasher tonight and noticed nothing was happening, but I was getting a clicking sound. I moved the dial to the right to off. As I moved the dial to the right, there were lots of clicks and clunks. I started over and turned the dial to the start position. Some water went in, but then nothing happened again. I clicked forward one click at a time. Sometimes water came in. Then water star


... Kenmore Dishwashers

Don't know the brand of my jetted bathtub, which blows water. The round on-off dial just stopped functioning - stuck in ON mode. Using GFIC, it turns on & off just fine, so problem is with the round knob. Unassembled dial and removed. Have piece that turns, round at top, narrow flat at bottom with a little black metal wheel that comes out. Wheel function not clear, given how dial turns unrelated to wheel. Inside hole, all plastic. Center spike fits into removed piece with wheels. 2 black pl


Ok this is not that easy to picture, any chance of emailing photo?([email protected]) the electrical connections will be somewhat remote to the dial so as to isolate the wet user from the power! can you after switching off at the breaker, get behi ... Dishwashers

Dishwasher is giving E1 which according to the manual is water sorce is off. We recently had turned the water off for bathroom repairs but the water has been turned back on, we have disconnected the pipes to run the water through, this is happening but as soon as reconnected to the dishwasher it doesnt work


Hi,This is common, there may be a flood protection device that tripped in the line or sediment got into the system when the water was turned back on.First turn the water off to the dishwasher. Take the hose or pipe off at the ... Maytag Dishwashers

I have a Sears (Briggs) 2550 washer mod # 580.752190, has been working great but when I got it out last week it wouldn't start with the water on, I turn the water off bleed the pressure out the wand and it started and ran great, I thought it might be the relief valve, I removed the valve turned on the water, a big stream was shooting out the hole where the valve goes, I started the engine and it ran but sounded like it was about half loaded. where do I go from here ? Thanks.


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

CI am having a problem getting our Miele G575 dishwasher to run through a wash cycle. It definitely has power, the water is on and there is no water in the bottom of the dishwasher. When you turn the dial to start a cycle, it hums but doesn't fill with water and doesn't progress through any cycle. We have tried all positions of the dial and have had no luck? Any ideas??


You said it does not progress...meaning the dial does not eventually move? it may be waiting on a water level sensor to be tripped. The dishwasher is just not filling. The water valve solenoid may be stuck or defective. or a wire may have come of ... Dishwashers

Dishwasher sounds as if it starts cycle, then stops, bleeps, and Fat and prewash lights come on. Manual says to turn off machine, turn off tap, wait 30 seconds and turn it all back on, but it doesn't make any difference. Manual says 'If the above does not solve the problem, check that the water feed pipe is not blocked' however, it doesn't say where this is, or how to do it. Please help!


Hi.You need to check the water inlet hose, that is the hose connected to house water faucet at the back of the dishwasher.Checck for blockage in the hose and ensure that the inlet hose is not blocked or kinked.If t ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Constant draining my candy cs445 17" is stuck on drain, it just sucks water out and wont stop. Turning the dial to stop does nothing, if i fill it with a sacepan of water it juts empties, and when all the waters gone its just keeps emptying, would a float switch be the problem or possibly a new dial ?


I would check the float.clean it up real good.make sure it moves freely.let me know ... Candy 17 in. CS455 Built-in Dishwasher

I ran a load of laundry in whirlpoo[ duet ht, model ghw9400pl4, error code p-09 was indicated. water was overflowing from door, and water was continuing to fill the tub. I turned off the faucets, unplugged & restarted in drain mode it hummed but would not drain. I turned the faucets back on and retried to drain but it would only hum. I manually removed the water by losening pump filter. There was no debree in filter except for a little bit of hair. The pump & vain was free & clean, and I co


It is your mixer value that is malfunctioning. ... Whirlpool Dishwashers

Model No. DU850SWPU3 AND SER. FT 4101406 TYPE 280-0. When cycle is complete and in off position the dishwasher fills with water. I find the bottom of the dishwasher standing full of water when I get ready to fill with next load of dishes. When I remember to turn off the wall switch this does not happen, however once in a while I forget to turn off the wall switch. The next day I find the bottom of the dishwasher full of water again. I then have to go through the cycles manually a couple of tim


If by turning the wall switch off, and only then it stops comming in, it means the board is faulty. There is a leak in the electronic system allowing to solonoid to stay partially open. Strangs that it doesnt flow onto the floor. ... Whirlpool GU2400XTP Built-in Dishwasher

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

My Teka Dishwasher DW7 80 FI does the first water intake operation, it sounds like rinsing, and the you hear the pump evacuating the water and two beeps as when it finishes the complete cycle. About 6 minutes. Then Stops. The lights that stayed on says error E8 according to the manual. I have done the suggested fix as ending the cycle manually and turning off and on the DW. I tested "many" times in various modes and the same preemptive end.


Hi.E8 is alternate washing system malfunction.The alternate washing system consists of a valve located in the underside of the appliance and connected to the impeller motor. The valve opens and closes switching spray on and of ... Dishwashers

I set rotary dial for Normal Wash which it does but does not turn off, rotary dial keeps turning automatically thru t Water Miser, Rinse Hold, Drying, Plate Warmer until reaches Off. Dishwasher operates normally otherwise. Have cleaned the pump and spray arm.


Hello, welcome to FixYa.I will start by saying your po ... Kenmore 17259 Free-standing Dishwasher

I have a Gallery 900 series GLDB958AS dishwasher. The cycle status lights (just right of the "time remaining" status window) continually blink. None of the buttons on the front panel work and every 10 minutes or so the water pump starts up for about a minute then shuts off. No water enters the dishwasher. I tried turning the power off then on but there is no change. Every so often a random cycle light will blink or light up for a minute, then turns off.


It seems that there is error on the program controller unit. All you need to check if that if there is moisture build up on the panels thus causing the programs to go harewire.\015\012So remove the panel and disconnect the wires, check all lead ... Frigidaire 24 in. GLDB958A Energy Star® Built-in Dishwasher

I have a hotpoint dishwasher model number HDA 460-03 AD and is dialed controlled when I turn the dial nothing turns on. no water no sound no nothing just a click. What could be wrong with this unit?rnCould it be the motor and how can I check that?


... Hotpoint Dishwashers

Dishwasher wont fill with water. just before it stopped filling i was turning the dial (a lot) between the wash cycles back and forth to attempt to get it to fill and drain (I didn't let it go through a cycle). We also removed the hose from the machine as it had split and replaced it and we had the machine tilted on it's side. the dial still clicks round but it sounds like the pump is going and it doesn't seem to be filling with water. Help


Hi. I suspect that the timer mechanism will be the culprit here, but i recommended to inspect and test the water inlet valve, before replacing the timer. The valve is a known problem area, as well. Follow the valve inspection procedure below, careful ... Fisher DS603W / DS603B / DS603I Dishwasher

Amana Dishwasher dishwasher will fill with water, then will proceed to just hum through the wash cycle, no water is pumping through the turning blades. It will stay humming until you turn it off by hand ( dial will stop mid way through cycle)


Sounds like something is jamming your wash inpeller start at the washer arm and go down till you get to the wash impeller and see whats sticking it like broken glass small peice of bone toothpick etc ... Dishwashers

Blanco BFDW4X Dishwasher - dial will run any of 3 cycles down right side, and then click back to start position, but will not automatically run the rinse down left side of dial, have to turn the knob manually. Also looking for a manual for this.. Susan [email protected]


... Dishwashers

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1995 seconds