Having problems with your Whirlpool Dishwashers ?

I have a Whirlpool GU1100 built-in diswasher that will not clear the pot & pans selection. It is stuck with the pots & pans and the cancel buttons lit and blinking. It will not start or clear. I have tryed to shut the power off for awhile and this has not helped. Other buttons can be pushed and will light but the other two remain blinking. If the clear button is pushed it will clear the other button but not the pots & pans or itself. Is this a problem I can fix myself?


Answers :

Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Whirlpool GU1100 built-in diswasher that will not clear the pot & pans selection. It is stuck with the pots & pans and the cancel buttons lit and blinking. It will not start or clear. I have tryed to shut the power off for awhile and this has not helped. Other buttons can be pushed and will light but the other two remain blinking. If the clear button is pushed it will clear the other button but not the pots & pans or itself. Is this a problem I can fix myself?


... Whirlpool Dishwashers

I have model GU3600XTSY2. Sometimes the pots and pans light flashes for no reason. Sometimes I can push that button and it stops. However, the cycle I select to wash the dishes is constantly interupted by the pots and pans (P&P) light flashing. If I push the P&P button, the wash cycle usually starts where it left off. Sometimes it will go back to the beginning of the cycle and begin all over again and get caught in a loop; start washer, P&P flashes, push P&P, begins cycle from beginning, P&


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My Asko D1996 Dishwasher will not start. The control panel has 3 lights staying on - position #1, 6 and 7 and are unresponsive no matter what buttons are pushed - even after turning the power off at the breaker, the outlet and the on/off button.I've tried holding down the start button for several seconds to reset but this did not work. I have also cleared the drain, filters and removed any water and pushed and held the Start button to reset.


... Asko Dishwashers

Kenmore dishwasher 16934 will not start up for me. I can push any button to set the cycle(pots & pans, china gentle, quick rinse, normal wash) and the time shows up in the display, but when I push the start, two red horizontal lines appear in the time remaining display. Cannot get the machine to start anything. All cycle buttons give me some kind of time remaining display but as I said, it ends up with 2 red lines. Thanks in advance. Mark


... Kenmore 24 in. 16934 Built-in Dishwasher

Control panel is locked. no buttons work when pushed. door panel says to push and hold ''heat dry'' button for 4 seconds to clear. nothing happens. this is on kenmore ultra wash dishwasher


Try unplugging the machine and wait 5 minutes. Plug it back in, the problem should clear. ... Dishwashers

I have a Kenmore Ultra Wash 15632/34/37/39. The Pots & Pans button is blinking constantly and I cannot Start the dishwasher. I tried pushing Hi-Temp, then Air Dry, then again. The sequence didn't work for me. If I press the sequence, then the Pots & Pans light blinks along with the Quick Rinse and Cancel buttons. Which combination do I use to get the dishwasher working again, please? Thank you.


Try to Press and hold AIR DRY for 4 seconds, to reset the dishwasher ... Kenmore 24 in. 15689 Built-in Dishwasher

I have a Kenmore Ultra wash 665 15895 dishwasher. It will not run any cycles. Symptoms: When I first close the door, the "Quick Rinse" light is on and the number 18 is displayed. When I push any button, the "Quick Rinse" light flashes continuously. If I touch any other button, both the "Quick Rinse" and "Pots and Pans" lights flash continuously. No matter what buttons I press, the behavior is the same. I've tried turning the power off and on, same behavior. The only button that doe


\015\012HiThis may be an issue with heater circuit, door switch or wash pump. Press and hold the heated dry/air dry button for 15 seconds....After, 5 minutes check if you are still getting the same error. If yes, ... Kenmore 15899 Built-in Dishwasher

We have a Kenmore Ultra wash dishwasher Model # 665.13733K601 and serial # FW18136133. came home from work yesterday and the pots and pan button and the normal wash buttons were flashing alternately. When I pushed the cancel button it started to flash, then I pressed the smart wash button and now its flashing. I turned of the breaker for awhile and then back on and the lights weren't on right away but later started flashing again, and I can't get the dishwasher to do anything. Any help on my pro


Hi,\015\012That unit took a power surge and the control is now bad....those controls can all of a sudden go wacky and the usual cause is power problems...\015\012The only way to fix it will be to replace the control...\015\012 ... Dishwashers

I have a GU1500XTLB1, type-575-0 Whirlpool Gold dishwasher. For the last couple of weeks I've been getting the control lock on. I got the manual out, I hold the air dry button and it clears. My problem is now when I turn the machine on dosen't matter which cycle I hit (pots and pans, normal, or quick wash) it runs for about 5 minutes and it goes into a mode with the timer having lines going horizontal with the air dry button lit up and rinse button lit up. It sounds like it starts the cycle


Hi,There are Few Tricks to Reset this. Follow the below Tricks :-1. Try holding down heated dry key for 5 secs. I believe that is the control lock/unlock button on your model. IF not, look for the lock symbol and follow same i ... Whirlpool Dishwashers

Have a brand new maytag dishwasher. When the cycle is finished the clean light stays on and I have to push buttons to clear is this normal?


If you open the door after the cycle, does it clear the display? Mine is a different maytag model, and when it's done it shows the display as clean. The display will go blank when I open the door manually... let me know if that helps.KEN ... Maytag 24 in. MDB5651A Built-in Dishwasher

My kenmore dishwasher, model 15822, just stopped working. The quick rinse light is blinking. The only other buttons that work are the pots & pans light which blinks when pushed, and the cancel button which will run through the 2 minute cancel cycle.


These are known to develop sticky switch contact pads. They stick in the contacted position and stifle the panel. Sometimes heat can be applied with a hair dryer to release them and make the unit function again. This is more than likely a temporary f ... Kenmore Dishwashers

My Dacor dishwasher will only do the 10 minute rinse cycle. No matter which button I push, it only does the 10 minutes rinse cycle. We have tried clearing it, we have unplugged it, we have tried every single button, but it continues to only do the 10 minute rinse cycle. What do we do?


... Dacor Epicure ED30 30 in Builtin Dishwasher

F70 fault cleared the drain valve which had a "button" from the screw holes on the side of the dishwasher - still the fault comes on and the machine runs even though its not turned on. One of the sites indicated the drain pan needed to be dried out but when I took off the kick panel could not see a drain pan.


Obviously the machine believes the drain cycle is not complete. It is running the drain pump until the level it "sees" is all the way down. Somehow you or your technician will need to get inside the beautiful stainless panels to adjust, clean or re ... Miele G 2630 SCi Stainless Steel Built-in Dishwasher

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. My buttons on top are Accusense, pots&pans, normal, light, glass express, rinse only Soak and scour Hi temp wash


I think I just responded to this problem. Please accept both if you are happy with the solution. ... Dishwashers

Maytag mdb6601aww push normal wash button-- nothing happens. push other wash cycles, the lights flash about 30 times then stop-- then nothing happens. tried clearing codes. hi temp wash then heated dry , hi temp wash then heated dry. same problem. also tried normal wash then heated dry 3 times in 6 seconds--- same thing. also tried unplugging unit waiting 10 minutes with no luck. thanks


... Maytag 24 in. MDB6100A Built-in Dishwasher

I set my dishwasher to pots and pans to run a dishwasher cleaner, and now when I push the auto button, the time reads 2hrs. instead of the 93 mins. it always read before. How do I reset the auto button to the way it came?


... Maytag MDB7100AWB Dishwasher

I have a kenmore dishwasher model 66516362300 and i just replaced the electronic control after replacing it flashes the pots and pans button if you push any of the other cycle buttons or cancel they start to flash too.


Yes, its the control panel (interface) that is bad, not the control board. Here is a website link to the one for your model. ... Kenmore Dishwashers

No reaction when start button is pushed on Kenmore UltraWash model 665 dishwasher. The clear /drain button works. No water filling


You have a bad water valve or bad user interface that's the long control in the front of the dish washer. ... Kenmore Dishwashers

Frididair GLD2250RDC0 The lights on the selection buttons (Normal cycle, pots and pans, no heat dry etc) flash when pressed. When the start button is pushed, it sounds like the cycle is starting, but nothing reallyhappems.


Sounds like the very common control panel issue. They have a tendency to short out due to overheating. It is possible it is the motor is bad, you can test power to motor with a voltmeter. If no power, then try power from control panel to motor. If th ... Frigidaire 24 in. GLD2350RCC Professional Built-in Dishwasher

New thermador dishwasher won't drain tried pushing the cancel and drain buttons inspected filters in bottom, they are clear


Did it ever drain???? ... Thermador DWHD64 Dishwasher

My dishwasher fills and then won't start the cycle all button work that is they light up and when pushed water comes in. The drain line is clear. thanks


This could be caused by a few different things. A bad water temp sensor, a bad float valve or a faulty control panel. The sensor can be tested with an ohmmeter. The float valve can be checked by removing the bottom panel. The control panel would also ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Dishwasher is full of water at end of the wash cycle. It drains when I push the cancel/drain button though. I dismanteled the drain hose from the pump and blew through the check valve to the drain. It is clear. This machine has a sensor after the drain pump. What does it do? Thanks Carl


The drain pump needs to be replace. ... Dishwashers

Nothing happens when I push buttons on the control panel of my dishwasher (KitchenAid KUDS011 JBS1). The drain is clear. It has been suggested that it may be the thermal fuse. What is the part number for the thermal fuse in this dishwasher?


The model number for your dishwasher is actually "KUDS01IJBS1". The character before the "J" is a capital "I" instead of the number "1". I just wanted to clarify that in case you need it for future reference.\015\012\015\012You are corr ... Dishwashers

Havnt used my dishwasher in 2 years on account of saving water. now when i push the start button some water flow into machine for a few minutes and then just stops. manual says to clean filters and drain pump but all clear. what is next plan of action?


Try pouring water from a bucket through the front. maintain the level. It should not overflow.Run a empty cycle. If there is a air block it will get cleared. ... Asko 24 in. D3120 Dishwasher

Clean light comes on my Kenmore Elite Dishwasher Model # 665.17263. This happened once before and has to do with the heating element. The service guy showed me how to press the buttons in a certain sequence to "unstick" the unit and it worked fine. The Quick Rinse light keeps flashing. When I push a previous sequence recommendation it switched to pots n pans and Quick Rinse and Cancel all started blinking. Then in about 2 minutes went back to Quick rinse. I did one sequence and it started to d


It seems that there is something stucks in your dishwasher...is there any error code? ... Kenmore 24 in. 15079 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0789 seconds