Having problems with your Whirlpool Dishwashers ?

Adp 2966 whm shows errorcode f9 - what can I do, few weeks ago it was f6. After removing waste water it worked again. Thx - johann


Answers :

Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Adp 2966 whm shows errorcode f9 - what can I do, few weeks ago it was f6. After removing waste water it worked again. Thx - johann


... Whirlpool Dishwashers

GE Dishwasher model PDW8200J03BB stopped draining. Removed the drain pump, checked with Voltmeter and there is resistance on ohms X10 of about 3. The flap is in place so water isn't shooting back into the sump inlet. Replaced the sump inlet about 6 months ago because it was deteriorated due to hard water. Pump worked fine after that. Checked drain hoses and air gap. Was able to blow water through. Pump only trickles water out at air gap. Does the pump need replaced?


Clear the line from the air gap to the drain,, if the rest is clear the only thing it can be is the propellers on the pump, i which case you will need to change the pump ... GE 25 in. Profile PDW8200J Built-in Dishwasher

I have a Bosch SGS46E22GB Exxcel dishwasher. It is failing to drain or pump out dirty water. About a year ago we had this fault and the engineer replaced the impeller jug. He showed my wife how to clear a blockage with the left hand side panel removed. I can't get the panle off so am looking for instructions on how to remove it. Thanks


... Dishwashers

Ken wood kdw60w10 dishwasher no hot water, there seems to be no power to the inline heating element, showing 30ohms resistance and power directly applied when removed from the dishwasher and it heats up. No fault codes on panel, works normally apart from no hot water, any other ideas? Many thanks


... Dishwashers

FDW70 dishwasher, starts to fill with water, shows pre wash on control panel, then pumps out within about 2-3 minutes, but has vertualy no water in it. Puts up code A10 on control panel, can still hear the pump going even when l open the door. Have replaced a burnt out heater tube with a new genuine unit, also have removed & checked fill valve & this works fine.


Hi,Try this few steps;Turn off the water supply to the dishwasher and remove the hose, turn\015\012on the machine for a couple of minutes in a fill position then turn off\015\012the machine, reconnect the hose, turn the ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Hi there, The error code 'strong and economy light flicker fleetly' is showing. the manual says that this means too much inlet water. We have drained the machine, cleaned waste pipe and tried to operate with a reduced flow from the inlet pipe but it's still not working. I filled the base of the dishwasher with water to see if it drains properly. It seems to be draining, but also leaking out of the base as well..? Any ideas?.


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Baumatic Dishwashers

Glasses and others things are not getting clean in the upper rack. A white film remains on the glass and stains are not removed. Also I'm having trouble with the silverware showing rust spots and not getting clean. I use Jet- Dry all the time. We bought it three years ago. The brand is JDB-5 and numbers inside the door are: JDB1270 AWY 36072124 LC MAX LOAD CHG 9. made in Newton, Iowa. We have had trouble with things not getting clean for quite a while, but it has gotten worse. The water is scald


If you have hard water, glasses can look spotted and cloudy even after cleaning. Sometimes changing the dishwasher detergent can help. The easiest solution to clearing up glasses that start to look cloudy is toadd some vinegar to t ... Jenn-Air 24 in. JDB1270AW Built-in Dishwasher

I have an shx65905uc bosch dishwasher that runs and works except for that there is not enough water pressure to rotate the top wand or operate the top sprinkler. The bottom wand does have water and turn and does the top but it is not enough to turn it. If i remove the bottom wand and plug it off then the top will work properly. I have cleaned all screens and removed the plate to access the pump and all seems fine. Any Thoughts


... Bosch SHX65P05UC Dishwasher

I have a bosch smu 2000 series dishwasher. it has always worked well with no problems but then all of a sudden a week or so ago, the water stopped coming into the dishwasher to wash the dishes. the faucet and all other water areas continue to work w/o problems (i.e. bathroom, shower etc). in attempting to use the dishwasher, the entire cycle seems to be working, i initially hear what sounds like an initial water discharge when the cycle first starts and during the entire cycle it sounds like it


... Bosch Dishwashers

The ge profile dishwasher model PDW8280J10SS was purchased about 2 yrs ago. It was working fine up until Jan. 2009. It ran fine but the water stopped draining. I read were you should run the garbage disposal prior to running the dishwasher. I drained the water and did this. It worked fine for a while then the problem was back. Once again, Drained all the water, sucked it out with a turkey baister, moved the dishwasher and checked hoses etc. Once again, it worked fine for about 10-14 runs. It now


It is probably clogged at the pump or before. See if you can get outlet hose off the bottom before the pump. ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

Hi Dishwasher BOSCH SMS53L02GB start of program digital display shows all sensor working. Water not pumping in. All hoses and filters checked OK Machine pumps water out then completes cycle in 1 minute. Water supply getting to base of machine An E21 code shows up on fault finding cycle


... Bosch 607335 Water Valve Assembly For Dishwasher

The Water inlet valve # 8531325 let water run outside the dishwasher. After removing the valve I found a small ball of contamination inside and removed it. It now works with out spilling water. Do I still need a new valve?


IF the valve stops and starts water flow correctly, no you would not necessarily have to replace it. The valve should have an inlet screen to keep this from happening again.. ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

Kleenmaid DW8 top washer does not operate. Apparent blockage in the water supply tube which runs up from the bottom water supply. How do I remove the bottom assembly comprising the main filter, waste trap and micro filter? I appears that these must be removed to access the water supply tube mentioned above.


... Dishwashers

Previous wash cycle worked perfectly. Next morning , dished not washed. Water pressure is insufficient to spray. Checked sprayers and clean. Removed bottom sprayer arm and tested. Water flows barely. Water fills but pressure insufficient to spray. Actually 'bursts' slightly on shutoff. All other functions work perfectly.


... Kenmore 16872 Built-in Dishwasher

I have an Ariston LI45. The stupid thin one. It's not seen much work & is just out of Guarantee. It's stopped working & is showing 2 flashing lights. Stops partway in to a cycle with water in the base, but not enough to cover the element. Tried re-setting, no difference. I have also noticed that it's melted a plastic wheel off the bottom tray at the back. After reading problems with other washers, i'm guessing the water level switch & maybe element too. If this is the case, i'm ok finding the


... Dishwashers

At end of cycle water remains in the botton; removed water by hand; unable to remove part over drainage area. show please how to do


Hello, With no information such as make and or model number it is hard to give you instructions on removing spray arm and accessing the drain...but before you start taking the machine apart you will need to check if your outlet hose is blocked...the ... Dishwashers

Cancel wash working fine. when ready to wash get humming sound. pumpmotor not turning. A glass dish broke a week ago and work fine till know remove screen today found some small brokeb glass - like when a harden glass brakes? if something is in the pump how do i remove pump


In\015\012most dishwashers, the water pump is located under the lower sprayer\015\012arm. This component pumps the water through the dishwasher. The pump\015\012has two impellers, top and bottom. These, as well as other components,\015\012can become ... KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher

Maytag MDB5000AWW started making noise when cleaning. Bottom arm working , but water isn't pumping with much force. No water coming out of top hole (removed arm to make sure there is no obstructions. Checked down to the impeller (didn't remove), and didn;t see any blockages, etc.


HI\015\012Motor malfunctions usually call for service by a professional. There are three main causes of motor failure: lack of lubrication, a defective motor switch, or worn or frozen bearings. A humming sound can be related to a burned-out mot ... Maytag Dishwashers

Water is not flowing into the dishwasher and as a consequence it overheats. In the couple of weeks prior we noticed unusual noises and taking longer to complete washing. Also since about two weeks ago dishes have had white mineral deposits and film on glasses. I suspect that the water pump is not working. I cannot find the salesslip from sears to see when we purchased the machine but I sus pect it was about 6 years ago. We are debating wther to have a service call, possibly including replac


Hi,\012Here is a tip that will help you to find out why water will not come into thedishwasher... Dishwasher Trouble No Water entering Dishwasher ... Kenmore 24 in. 16262 Built-in Dishwasher

I just bought a used LG LDS 5811ST stainless steel built in dishwasher. The previous owner said he bought it 4 years ago. It's in great shape but doesn't work. It powers up but the water is not pumping into the dishwasher. The previous owner said that he thought it was the pump. He said he took it apart once and cleaned a bunch of crud out of some hoses and it worked for a while then started making funny noise and stopped. When i got it home i powered it up and connected water hose. It seems to


Rom the Service Manual:"1E INLET ERROR Not reached to the normal water level in spite of 10 min. water supply.The Hall sensor is OK?Check the frequency of Inlet Water by the Test Mode." ... Dishwashers

My SGS55M72AU/65 does not get rid of its drain water, although that wee pump in the bottom is clearly working (which I could see after removing filters and pump cover). There is no blockage near the drain pipe connection, so I infer there is a blockage somewhere inside the dishwasher, in a place I can't get to without further instruction. I've removed most of the drain water and pulled the unit out, so I could lay it on its side and start taking screws out. But I much prefer to have some guidanc


Ok i am attempting to help you although i dont see your make of dishwasher but im using what i know without manual. to ensure there is a blockage in the dishwasher remove that hose you checked at garbage disposal or vent and leave it disconnected an ... Dishwashers

Dishwasher not working. Two weeks ago the heating cycle didn't switch itself off but appeared to correct itself. Now there is no water in the cycle... pump and heater working, just no water reaching the arms of the dishwasher. Any ideas why?


Sounds like a bad pump. If it drains the water and doesn't deliver at arms the pump is more than likely bad. First of all pull the water supply line off and see if there is build up from hard water on the in-line screen (if present), then If you are ... Whirlpool GU2400XTP Built-in Dishwasher

I have a KARCHER Model K 2401 which onstart up has normal water pressure rather than the high. I can usually get it to work by removing the tip, pressing the trigger and running some water through without the tip on. The i replace tip and it will usually retain the high pressure. If I stop depressing the trigger I have to go through these same steps. It is like it loses prime. It works well once I get it started putting out the high pressure.


... Karcher 2500 PSI Pressure Washer

After replacing my garbage disposal, my dishwashr stopped working. I did forget to remove the stop plug from the disposal unit. But even after doing this the unit still does not work. It does turn on but no water drains out. In addition when using the sink it appears that some water may be getting into the dishwasher.


The drain line from the dishwasher MUST be secured HIGHER then the drain port in the disposal.If this is not the issue,the dishwasher drain solenoid is not functioning correctly. ... GE Nautilus 24" Built-in Dishwasher

SMU2046UC: waste water won't empty. Wash cycle works like it should but waste water remains in the bottom of the dishwasher. Sounds like pump is humming and there don't seem to be any clogs in the system??


Most likely a blocked pump. You should be able to access the pump from the base of the unit under your filters. Remove the cover and rotate the pump impeller to free blockage then start any prog to check if pump is working,if OK reassemble, if not re ... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1821 seconds