Having problems with your Whirlpool Dishwashers ?

My dishwasher has water standing in the bottom after cycle is finished. Clog? Pump problem?


Answers :

Check the drain line and the connector to the pump for clog.
Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

Whirlpool dishwasher: Model DU920PWKT0; 8 years old Lately, have noticed not full drainage of water at end of cycle... about 1 inch standing (thus 2 inches at the sump). Glasses have had noticeable film on them. Ran the rinse cycle a number of times to explore problem. When I interrupted the cycle, the water on the bottom was soapy, yet no new soap had been introduced. I even colored the water "left" in the tub to see if it was replaced by fresher water. Although it was going through t


Find the 'tech sheet' behind the front 'kick plate' of the machine. This doc will give you a troubleshooting procedure for that specific machine. Check drain line and make sure it's clear and not kinked. Is filter clean?Has machine ... Dishwashers

My Kenmore Elite dishwasher did not drain the water out of the bottom after the dishes were washed last night. Could I possibly have pushed a wrong button to keep it from draining, or do I have a problem? All the dishes were clean. Should I run it through another wash cycle? I've got water standing in the bottom of my dishwasher.


Yes , If the program controller has hung it would have skipped the drain cycle. So try to redo the cycle and see if the drain works, is not check the program controller and the drain valve/pump.- if there is food particles that have clogged and block ... Kenmore Dishwashers

Leaking dishwasher The dishwasher leaks a stream of water at the base -bottom left corner whenever it goes into the final rinse cycle. It does not leak when it is in the wash mode. This leak just seemed to develop suddenly. There was no build up -ie a small stream of water. I just noticed a big puddle on the floor one day after dishwasher had completed its cycle water leak in the left side ,bottom ,husband states a small drip,drip and we do not know what to do or replace. No water standing


I just had this same problem and it was caused by a small plastic seal on the bottom of the door. My friend owns an appliance store and he said this is a common problem for this model of dishwasher. The part was $68 and the labor was $60. I could ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

My dishwasher won't drain. It runs through the whole wash and dry cycle...and when I open it to unload the dishes the bottom is filled with standing water. None of the lines that I can see appear to be kinked, and I'm not sure what else to check. I inistalled the dishwasher myself becasue my husband was working out of town...this was about a year ago. Haven't had any problems with it until now. Thanks for any help or suggestions you're able to offer. Christine Fitzpatrick


If you hear the drain pump run after wash and rinse cycles then it is likely the problem is in the kitchen drain end. Have you got a disposal unit in the kitchen sink. Sometime it is full and causing a block.\015\012\015\012If you don't h ... Dishwashers

Model No. DU850SWPU3 AND SER. FT 4101406 TYPE 280-0. When cycle is complete and in off position the dishwasher fills with water. I find the bottom of the dishwasher standing full of water when I get ready to fill with next load of dishes. When I remember to turn off the wall switch this does not happen, however once in a while I forget to turn off the wall switch. The next day I find the bottom of the dishwasher full of water again. I then have to go through the cycles manually a couple of tim


If by turning the wall switch off, and only then it stops comming in, it means the board is faulty. There is a leak in the electronic system allowing to solonoid to stay partially open. Strangs that it doesnt flow onto the floor. ... Whirlpool GU2400XTP Built-in Dishwasher

I have a brand new whirlpool DU1055XTV5 dishwasher, installed two days ago. After the cycle completes there is about 1/2" clean standing water left in the bottom. It is not just down in the well area, the whole bottom is covered with water. This is after running a normal cycle with no other options such as sanitize or heat dry. I called Lowes, the store that sold/installed it, and they said this is normal in new dishwashers to keep the parts wet. They said as long as the water does reach th


... Whirlpool DU1055XTS Built-in Dishwasher

1" of water standing in bottom of dishwasher after cycle? what is the problem


Hi\015\012 \015\012Dishwasher not draining issue usually occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no v ... Asko 1375 Dishwasher

I have a GE PDW8280J00SS dishwasher that doesn't drain properly. After the cycle finishes there is about 1 inch of standing water left on the bottom. Any suggestions what the problem could be?


... GE Dishwashers

In our KitchenAid dishwasher, there is often a puddle of standing water in the bottom of the washer after the cycle has finished. It never seems to drain and I have to "bail" it out. Is there any easy fix for this problem?


Check the drain to make sure its not plugged with food (the most common problem). If the drain is good then check the hose to make sure its not plugged anywhere inbetween the dishwasher and drain under sink. If all those check out, chances are your ... Dishwashers

We have a built-in Whirlpool dishwasher model DU850SWPSO type 280-0. It does not drain at the end of th e cycle. Water stands in the bottom and more stays each time we use it. What can we do to solve this problem?


... Whirlpool 24 in. DU850SW - Multiple Color Free-standing Dishwasher

My dishwasher has water standing in the bottom after cycle is finished. Clog? Pump problem?


Check the drain line and the connector to the pump for clog. ... Whirlpool Dishwashers

I opened the dishwasher while it was washing and later discovered water standing in the bottom. This happens now when I run a cycle. I have misplaced the manual and don't know how to reset, but think this might be the problem.


... GE 24 in. GSD4920Z Built-in Dishwasher

CI am having a problem getting our Miele G575 dishwasher to run through a wash cycle. It definitely has power, the water is on and there is no water in the bottom of the dishwasher. When you turn the dial to start a cycle, it hums but doesn't fill with water and doesn't progress through any cycle. We have tried all positions of the dial and have had no luck? Any ideas??


You said it does not progress...meaning the dial does not eventually move? it may be waiting on a water level sensor to be tripped. The dishwasher is just not filling. The water valve solenoid may be stuck or defective. or a wire may have come of ... Dishwashers

Kenmore dishwasher. The upper rack is not getting clean. Even very light residue remains. And, detergent is left in door at end of cycle. The bottom is filling up, so I don't think it's the intake valve. Also, all the blade openings appear clear. I am noticing that hot water is not filling the dishwasher when I first run the cycle. Even if I have hot water running in the sink, the dishwasher fills with cold or warm water. So, I think this is the problem. What should I do? Thank you in advance!


I find it odd that the dishwasher is filling with cold water if the water is hot at the sink. It sounds like the dishwasher is connected to the cold water line rather than the hot. Check under your sink; if you've got standard plumbing, the dishwas ... Dishwashers

Water seems to be leaking into the dishwasher at the end of the cycle the water appears to be clean, so I am wondering about a seal of some kind on the hot water line leaking or whatever. It is a Bosch Dishwasher SHU series 3200 My problem is the same. Water leaks in to bottom of dishwasher over about a 2-3 day period. The dishwasher runs fine. It does not ever run over. The water seems to stop entering the dishwasher after it reaches a certain level.


You have a bad water valve. When the unit is off, the valve should seal and the water should not flow. Something has gotten in the valve and is keeping the needle up or the diaphram in the valve has deteriorated. replace the water valve and you wil ... Dishwashers

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

Kitchen Aid model KUDS01FLSS3, water gets pumped into bottom of dishwasher but when the cycle needs to change to shoot the water over the dishes nothing happens. When the cancel button is pushed all the water will drain.I have cleaned out the bottom drain compartment that was jammed with calcium build up and guck. Would this be a pump /motor problem or electrical circuit board problem?


... KitchenAid Dishwashers

Kitchen Aid model KUDS01FLSS3, water gets pumped into bottom of dishwasher but when the cycle needs to change to shoot the water over the dishes nothing happens. When the cancel button is pushed all the water will drain.I have cleaned out the bottom drain compartment that was jammed with calcium build up and guck. Would this be a pump /motor problem or electrical circuit board problem?


... KitchenAid Dishwashers

Kitchen Aid dishwasher Model# KUDP01FLSS. 2 problems #1 Won't run unless you press in on the door and hold it for a few minutes then it runs through cycle normally. Problem #2 It won't drain water out at the end of the cycle when I open the door there is water laying in the bottom of the tub. I have checked the drain hose for clogging and it appears normal. I am able to remove the hose from the disposal and suck the water out of the tub using a shop vac this indicates to me that the drain is ope


... Dishwashers

Leaking dishwasher There is standing water in the dishwasher when it's not being used. Recently we had a garbage disposal installed and was wondering whether this may cause the water from the sink to settle in the dishwasher. Also, the water rises and leaks on the floor. We have to run a wash cycle to drain and dry out the dishwasher. What do you think the problem is?


It sound like while the assembly of the garbage disposal, you placed the end of the drain line pipe in a lower position than it was before.\015\012Good luck! ... Kenmore 15129 Built-in Dishwasher

Help! My Whirlpool Quiet Partner II isn't working at all. Water was standing in bottom at end of last 2 cycles, but on the last cycle, I came home to clean looking dishes, standing water, and a machine that won't turn on at all- no lights on any buttons- nothing works. I've tried the reset codes published here and elsewhere, but there are no lights on any buttons at all. The circuit breaker is fine. I have 3 young kids and can't function long without my dishwasher!


There is a fuse in the control panel what your model# i can get you the part number its easy to replace it. ... Dishwashers

I have a GE Potscrubber 720 and there is water in the bottom of the dishwasher and I tried to clear it by starting a cycle and it still keeps water in the bottom of the washer. When I run a cycle there is caked on soap on the inside door and dishes and the dishes are filthy. I found a long thin piece of metal by the drain it is long and straight and a break on one end and an "L" shaped bend on the other.. Any ideas where to start looking for problems? As I have no experience in repairing dishwas


... GE 24 in. GSD2600GBB Built-in Dishwasher

Upon completion of the washing and drying cycle there is water in the bottom of the dishwasher. We ran the rinse cycle and there was more water in the bottom. Do you have any possible solutions to this problem?


\012Hi,\012Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... Dishwashers

All of a sudden, my Kenmore dishwasher (Model 363.1411691) will not cycle. When I lock it shut and try to set it to wash, all I hear is a click--no motor running, no water sounds. As I advance the timer knob, I just get clicks where each cycle should begin. There is standing water in the bottom of the dishwasher which does not drain out. Any advice would be much appreciated, for sure.


Hi.The clicks are simply the relays in the timer board that try switching on. The control module is likely working.The cycle does not start because of a different problem.If no light is coming on, then ensure that wall socket ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2575 seconds