Having problems with your Whirlpool Dishwashers ?

I have an ADG7550 whirlpool dishwasher. Am experiencing a fault when placing on a normal 65 degree programme it starts to fill and then defaults to pre-rinse and the start button and light flash eleven times. Can you explain what type of fault this could be ? I have had a similar problem 12 months ago when it was described as a water pressure problem which again was in the winter and wonder if this is the same. I would add that if I re-set the start button by holding it down and then re-start


Answers :

Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an ADG7550 whirlpool dishwasher. Am experiencing a fault when placing on a normal 65 degree programme it starts to fill and then defaults to pre-rinse and the start button and light flash eleven times. Can you explain what type of fault this could be ? I have had a similar problem 12 months ago when it was described as a water pressure problem which again was in the winter and wonder if this is the same. I would add that if I re-set the start button by holding it down and then re-start


... Whirlpool Dishwashers

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons


... KitchenAid Dishwashers

Hi, I have had a few issues with my ST663 machine. The current problem: the rinse cycle light keeps flashing and it doesn't start when you shut the door. I have tried holding down the right button but it beeps twice and nothing happens? Also tried holding both buttons down for a while and still no success. I got a new electrical board installed not that long ago so not very happy hoping it not a big issue. Do you have any other things that I could maybe do?


HiIf you have already tried to reset the unit by pressing the High Temp wash-heated dry button for 3-4 times in sequence then the problem is either with the door switch or the keypad itself that has gone bad and should be replaced. Hope t ... Dishwashers

My Amana dishwasher will not start anymore. The selection panel lights stopped turning on a few months ago, but we could still push the start button to start the cycle. Now that won't even work. Obviously an electrical panel problem, but what can I do to fix it?


... Amana 24 in. DWA22A Built-in Dishwasher

I have a whirlpool DU943PWKQU, first about 6 months ago all the push buttons except light wash stopped working. Now this week it started giving me problems starting all together at first I resolved by unplugging and replugging the electrical cord but this is no longer working. Can you tell if something can be done?


It seems to be the program controller and you will have to get this checked. Remove the power off for some time and reset it back . If the programs are not responding then you will need to check from the power cord to the control panel to see if this ... Whirlpool Dishwashers

Throttle problems Homelite pressure washer model UT80709A. bought it 10 months ago with no problems and stored it for last 9 months. Before doing so, drained gas, oil. Brought out of storage a few days ago, filled with fresh gas, oil, cleaned air filter. Starts great first try but after about 30 seconds the throttle starts visibly revving the motor a litlle at first then gradually faster and faster until it seems to flood and die. Then you cant start for about an hour and its the same story. Hav


... Homelite Pressure Washers

My Kenmore Diswasher (Mod # 665.17842400) has crapped out again. Towards the end of a cycle, the power seems to have been lost. There is now water in the bottom, and the user interface won't come on. 2 months ago I replaced the user interface and the magical board it connects to to solve a start button problem. I checked the power coming to the washer and it is live.


There is a thermal fuse on the control board. It protects in a overheating problem or sometimes when there are to many appliances on the same circuit that creates a high amp draw, that melts the fuse not actually blowing it like a short. Check your d ... Kenmore Dishwashers

I have a hobart lx-g model which i purchased used a month ago. At the start everything worked great...then when ever i would push the "off" button it would shut down and restart by iteself... lately i've been getting lots of error msg's (one was E4...) and now it overflows all the time, its as if it's gone banana's... what do I need to do to fix my problems (chane the cpu???)


Hi,Initially would suggest to check that the power supply requirements are satisfied. You might also need to check the breakers. Depending on the exact model number, the AC supply can be as shown below: ... Hobart Dishwashers

The start/pause button beeps when pressed to start a program and the machine gives a beep in response and appears to start its initial sump emptying phase but stops within 1-2 secs. Have checked pump and found no problem but start time is so short that in cannot have sensed a problem in the pumping circuit. If I persist in holding the start/pause button in, it can be released after the initial sump emptying phase (2-3 mins) and phase 1 of the wash program goes to completion. At the end of the


Hi\015\012\015\012Ronald...the beep sound itself indicates an issue with the\015\012membrane switch (control panel) and it should be replaced. I believe that the\015\012pump and motor is fine as its just beeping and doing nothing else. Ho ... Smeg 24 in. DWI612 Built-in Dishwasher

The start button flashing continuously and the filter area seems to be full of water but when I take it out it is perfectly clean. I have switched the machine on and off several times but each time the start button indicates a fault. I have tried holding down the on button so as to stop the start button flashing so that I could select a program - this did work once and I selected my program but 10 mins in it stopped and started beeping... I have a ADG7460 machine - HELP! I'm going crazy!


Please clarify what you mean by "..but when I take it out it is perfectly clean.." are you saying the water in the filter area is clean. \015\012\015\012Turn the power off and take out all the water by hand using a small container. Turn t ... Whirlpool Dishwashers

My kitchen aid dishwasher will not start I replaced the interface control board thinking that was the obvious problem. When you go to set the dishwasher to start some of the settings don't always light up then when you push the start button the lights will flash then start but it's not flashing and won't start. I get lucky once in a while and get it to flash then start. I don't know where else to look. I don't want to start replacing parts one at a time till I get lucky. My model # is KUDIO1F


Check all cables especially the ribbon cables from the user interface to the electronic control assembly as steam from dishwashings will create small amounts of corrosion and inhibit signals to and from these 2 components,unplug each,inspect,and reco ... KitchenAid Dishwashers

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

I have a LG LD1403W1, when you turn the power button on it sounds like it is shorting out. You can then oush the start button it commences to wash the dishes. After about 3 minutes the FE fault starts but continues to wash. There was a electrical burn smell when this problem first started. The dishwasher then stops.


... LG LDF8812 Stainless Steel Built-in Dishwasher

Whirlpool Dishwasher ADG 450. Start as normal and it keeps intermittentlly stopping and starting. Washs / drains fine, but sometimes cycle seams to last for a couple of hours. I think it is four beeps when it is stopping and then immediately starts again. We had a problem months ago where as the sink was draining into the dishwasher out pipe, so dishwasher wasn't draining / filling up. Fixed the problem by turning the pipe the other way so water couldn't flow that way - but I don't know if that


... Dishwashers

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

My Whirlpool ADP6565 dishwasher stops before the rinse cycle. The start button then flashes and the rinse light on the cycle selelector knob is lit up. if I hold the start button in the water pumps out and then stops. I have to manualy set it to rinse to rinse the dishes.


You may have a blocked faulty, pressure sensor, or the hose is not flowing freely? Check that out.\015\012\015\012Below please find a service and repair manual, if you use the troubleshooting steps you maybe able to isolate your issue, and affe ... Dishwashers

Dishwasher does not seem to have power. I have a Kitchen Aid, under counter unit, 9 years old, model KUDS01I. I used it 2 nights ago with no problem. When I push a button, nothing happens, no lights show, etc. It is plugged into the lower half of a duplex socket with disposal plugged into the top. Disposal works, so the problem seems to be with the dishwasher. That also eliminates any issues related to breakers or ground fault indicators, etc. Is there a reset button on the dishwasher? Is there


... KitchenAid Dishwashers

Cloudy Dishes This condition suddenly started after couple of years. Water heater is 7 yrs old, never drained, therefore I think this could be the problem. I am going to drain it and report. I do have a whole-house water filter which I change out monthly or every other month. My guess is that without it, this problem would have surfaced long ago.


The problem is hard water. Go to www.dishwasherfilter.com and get their new product. It filters the water and takes out the hard minerals that cause spots and clog di ... Amana 24 in. ADB2200AW Built-In Dishwasher

I have a Maytag quiet series 400 dishwasher. I set the required buttons for a wash, inserted the soap in the soap tray but the machine will not start. Previously, when the washer would not start, I opened the door and pushed down on the soap tray and its seemed to fix the problem. Next time I used the machine, again not starting, but by pushing on the soap tray it would not start. Can you suggess what the trouble may be or give me a check list that I may do before starting the washer. This machi


... Maytag Dishwashers

When starting my Bauknecht GSFP 5586 dishwasher the program is set for rinsing and the start light flashes two blinks, then again two blink etc. I cannot get the program to change. When I hold the Start button for 2 seconds, the progress light flashes at END for a moment then reverts back to the double blink sequence. I have checked the filter and it is well seated and clean. What can I do to start the program selection again?


Ok, so I had the exact same problem with the exact same model. NOT 7 blinks and to buttons that you do not have.\012I will tell you what I did as I do not know what (if any) of what I did fixed it (it could be luck but I do not think so).\012 ... Dishwashers

I have a Triton Aspirante Topaz shower which I purchased 2 years ago. Just recently it has started to give me a problem. With the temperature control set normally to 43 the shower goes through its pre


... Dishwashers

My dishwasher won't start (Series 300 purchased 14 months ago). The following lights are on: light wash,hi temp wash,sanitize, locked and the start /resume light is flashing put goes out when pushed and the machine does not start when closed. there has been an on going problem with the regular wash light not coming on when pushed.


Hi\015\012\015\012It may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting t ... Maytag 24 in. MDB9750AW Dishwasher

Have a KUDS24SEAL5 superba and no lights come on after pressing any of the buttons. Power to machine is good. Several months ago it would not start properly by pressing 'start'. Would go directly to 'drain' cycle. Then found that if we pressed 'rinse' before 'start' it worked fine. Now, almost a year later...no lights, no one home...any thoughts?


I had a KUDP02CRB and there is a hidden transition connector on the front panel under a black plastic cover that was pulled out a little. It connects the flex cable from the controller board to flex circuit of the panel. I just pushed it back in al ... KitchenAid Dishwashers

Our Ikea Nutid Whirlpool dishwasher locked up recently. It started when someone was wiping off the top of the door where the control buttons are located. The dishwasher was locked on the china setting. Holding the cancel button, shutting off the breaker did not seem to clear it. Is there a way to reset the dishwasher? There was flashing on buttons but I cannot remember how many flashes or what one was flashing.


... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1559 seconds