Having problems with your Whirlpool Dishwashers ?

Whirlpool Undercounter Dishwasher DU8900XY1, My dishwasher is dead. It stopped in the middle of the wash cycle and has not operated since. I checked the power at the junction box and power was confirmed. I could not see or smell any burnt wires. I don't know the next thing to trouble shoot to fix the problem. Please help


Answers :

Take off the kick panel and open up the j-box at the dishwasher only. Just make sure there is no burned wire nut or loose one\012
\012Thanks
Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Whirlpool Undercounter Dishwasher DU8900XY1, My dishwasher is dead. It stopped in the middle of the wash cycle and has not operated since. I checked the power at the junction box and power was confirmed. I could not see or smell any burnt wires. I don't know the next thing to trouble shoot to fix the problem. Please help


Take off the kick panel and open up the j-box at the dishwasher only. Just make sure there is no burned wire nut or loose one\012\012Thanks ... Whirlpool Dishwashers

Burning smell from our Dishwasher. I opened it up and found a little square brown thing attached to the motor - It has a terminal at one end that a white with a coloured stripe cable attaches to via a slip on terminal and 2 terminals to slot the little unit directly into the motor. Anyway, this little unit has obviously burnt out and this is the problem. Except my problem is that I dont know what this little unit is, so dont know what to ask for at the spare parts centre. Can anyone identify


... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

Its a whirlpool dishwasher washed dishes last night dishes were clean but rinse water was still in the tub now no lights come on the touch controls its like its dead, i checked power and got it to the circut board but dont know how to check any thing else


Hi.... you have a Bi-metal bad .. It has opened You can by-pass it by using one wire and I bet it lights up ... dont leave it by-pass..... The bi-metal is right on the main board ... Dishwashers

I'm installing an electrolux dishwasher, the first thing I'm going to do is the electric wire. I know I have to attach the black white and green (ground wire).I've done this before with my Maytag and it was a breeze. When I open the elec. box on the electrolux dishwasher the black white and green wires go into the box from the Dishwasher and then THROUGH THE BOX AND THEN BACK INTO THE DISHWASHER>>>>>THERE IS NO END........... In the Maytag I just opened the box on the dishwasher and the ends of


There should be a complete wire connection already there ready to be plugged in. If not, typically at the back of the unit there should be a black plastic box that when opened will indicate 3 terminals. live - neutral - and earth. Looks to m ... Electrolux Dishwashers

No Power I have a bosch shx33 dishwasher. I just replaced the water valve because of a leak and now I can't start the dishwasher. It's like there is no power to the unit. I know there is power because I get a shock if I touch the two wires that are connected to the water valve. Is there another trip switch or something somewhere?


First let me say that using parts of your body to test for mains electriciy is a VERY VERY bad idea. You are lucky you are not dead. Please do not touch live parts again, get a multimeter or a mains tester.\015\012\015\012If there is mains across the ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

Dishwasher fills with water and then stops. No lights are on at all. I cked wiring and circuit breaker and no issues there. I then flipped off circuit breaker over night. Got up next morning and flipped breaker back on. Dishwasher lights were on and when I pushed Start button, it ran fine. Now it is doing same thing except circuit breaker trick dont work like last time. THERE is NO issues with wiring or connections to dishwasher.


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

I have A bosch dishwasher she4am16uc/06 and it has been disconnecter for a while. I re commected it today and when I turned the power on the dishwasher started running but it wqs in the quick wash cycle. I dont know how to get it on power scrub. can you help?


... Bosch Dishwashers

My dishwasher so my dishwasher seemed to have quitworking during a cycle. like breaker triped or something. i checked the breaker and thats fine. it seams like its hard wired in though. Would that be right? and is there a fuse or something that could/would blow during a wash? I dont know what model it is or anything it was in the house when i got it. The dishwasher is built in and it seems decently old its a kenmore ultra wash and it has like 10 buttons for the differend cycles on the left and a


Sounds like the fuse on the control blew. you can replace the fuse for\015\012around $20 or you can cut and splice the wires for free. If that doesnt\015\012work then you may have a loose conection in your junction box under the\015\012dishwasher. ... Kenmore 24 in. 15932 Built-in Dishwasher

Dishwasher fault had leak,when opened bottom plate, could not see any obvious leak problem,hand dryed what componets i could. made sure no wires were loose then screwd back bottom plate,turn power back on but power button flashing continuously know,any advice plz


The flashing power button is a bad sign. You may have flooded the circuit board out or there may be a bad component as a result of the flood. Difficult to know from here.\015\012\015\012Most flooding on dish washers is caused by a faile ... Dishwashers

I have a kitchen-aid dishwasher model kuds01flss0. all of a sudden i can't get it to turn on. did the usual...breaker, power cord, ect. there is power going into the unit. dont know where to go from here


Hello, I sometimes have luck by turning the breaker off for a solid 5 minutes. Not 4 and half but 5 minutes. This sometimes resets the control board like rebooting a computer. If that doesn't do it I'd start by checking for 120 volts at the power con ... Dishwashers

We have a Bosch SHU9925UC dishwasher, installed in 2002. In August 2010, the water didn't drain, and a service technician discovered melted wire nuts at the main incoming power junction, presumably due to a loose connection there. He re-wired it. Now it's March 2011 and yesterday we smelled electric fire smoke coming from the dishwahser, opened it up and again found melted wirenuts. So is it really just poor installation, given that now 2 different installers have created the same problem?


... Bosch SHU9925UC Built-in Dishwasher

Towards end of dishwashing cycle error code comes up and consitently beeps, can not turn off by machine buttons or reset. We have to reset by power plug. Water is left in bottom of macine, dishwashing powder is left on most things. Rinse button then works, it then drains the machine no problem. So I dont think it is the pump.


No response ... Dishwashers

I have a new timer unit for my ariston LS2020 dishwasher, dont know what color wire go on what wire tap on the timer. The new timer c00057632 is not same as the old .


... Ariston Technologies Dishwashers

My dishwasher did not come with power cord. what kind of cord do it need and how do i connect the cord? On the new cord how will i know which one to connect to the white and black wire? The dishwasher is Whirlpool model du930pwsb, Sku numbmer 451-5344.


120 Volt 16 gauge, 3 wire power cord.\015\012\015\012Brass Screw is Black, White Screw is is Common, Green is Ground....Try Home Deport for a cord. If no screws are on the dishwasher, use wire nuts and elec. tape ... Whirlpool 24 in. DU930PWP Built-in Dishwasher

Continuous alarm after a power failure an alarm started going off in the door of the dishwasher. the push button panel is not functioning. I opened the door panel and found an electronic control circuit board. It is this board that is making the noise. I unplugged the black and white pair of wires on the lower right side of the board and the noise stopped. this must supply power to board. Anyone know what this problem is?


I posted this under "Ben's" problem as well, but I had the exact same problem. I know which black and white wires you're talking about. I don't know what causes this, but getting new parts did fix it. The black box that all those wires go into on ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I purchased a used Dishwasher KUDE70FVSS but it will not power on. I have checked the power up to the control panel. An earlier posting said to replace the thermal fuse. I don't have a wiring diagram so I don't know where to locate it or what it looks like. Thanks David


HI. This is true. There is a thermal fuse that will burn out under adverse conditions. This could be a power surge or element failure. This fuse is mounted in close proximity to the main board. Both parts are housed within the control panel. The actu ... KitchenAid Dishwashers

I have a jackson inferno dishwasher model H4131. i want to know if the wires going out are all hot leads to the box i dont know if one of them are neutral! is the break a 2 pole or a 3 pole breaker?


... Jackson 25 in. TempStar HH/GPX Free-standing Dishwasher

Burnt wiring insulation dishwasher & aluminum house wire


Your problem is most likely the aluminum wiring. Begin by running a copper line to your dishwasher eliminating the aluminum. use Romex Building Wire, NM-B 12/2 with ground and a 20 Amp circuit breaker ... Dishwashers

During power scrub cycle which is the one we use most of the time the dishwasher stays at one minute fot a long time. the dishes come out clean and it finally does finish cycle just dont know why it takes so long on last minute of cycle for so long


It's just heating the water more ... Bosch 24 in. SHU43 Built-in Dishwasher

Dishwasher won't drain, Smells like burnt wire


... Kenmore Dishwashers

During the cycle, dishwasher stopped, and has a burnt electrical smell coming out of the vents in the door. There is no power in the control panel. Checked circuit and plug.


Sounds like the motor burned out. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

After a power surge the dishwasher does not work at all. It just beeps constantly. There are no lights on the touch pad at all. The only thing that stops it from beeping is to remove the 2 pin black and white wires. I replaced the control module. Nothing changes. Do I need to replace the touch pad? What about the 3 digit clock? These parts together cost 145 dollars. I do not want to buy these parts and put them in to find out that did not fix the issue. I also unplugged the


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

My dishwasher makes a burnt plastic smell everytime I run it. I have checked all the possible places for things to get stuck and find nothing.


Hi,Refer to :-http://www.ehow.com/how_4677286_remove-melted-plastic-odor-dishwasher.htmlThanks. ... Dishwashers

The water is pumped out after the rinse cycle then it continues to run and make an unusual noise but nothing happens. The noise is almost a grinding sound. There is also a smell like some part may be hot or the wiring may be hot. I can reset the dishwasher and re-run the cycle up until that same point and it does the same thing again. I have had a repairman out twice in the last six months. The first time he could find nothing wrong because the problem was intermittent and he couldn't see anythi


Timer \015\012\015\012or\015\012\015\012 ... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2352 seconds