Having problems with your Whirlpool Dishwashers ?

I have a whirlpool du1055xtsq3 dishwasher that is not working. Start button does not light and can not run wash cycle, but other buttons do light up when pressed. Can I fix this myself or do I need to put in for a service call? Thanks!

Answers :

Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a whirlpool du1055xtsq3 dishwasher that is not working. Start button does not light and can not run wash cycle, but other buttons do light up when pressed. Can I fix this myself or do I need to put in for a service call? Thanks!

... Whirlpool Dishwashers

Whirlpool model DU960 - from 2001, I think. Stopped running mid-cycle and the cycle lights flash. Won't run. How to fix? If I press 'Cancel/Drain', it flashes that button light. If I press one of the wash cycles again, it turns on the pump for about 1 second, shuts off and the lights flash again. I tried turning off the circuit breaker and turning it back on, but it still won't run. Is this fixable? Do I need to call for service? Or, would I be better off just replacing it?

I have a whilpool du960 the rinse only light is flashing and the light wash light is also flashing. ... Whirlpool Dishwashers

I have a Kenmore Elite, model number 665.17263. The clean button green light is flashing. This happened once before and it was the heating element. The service guy showed me how to put a series of presses on the buttons in the front and it was fixed. I lost that paper. Can you help

You may just need to reset your control board. Go to the link and it will explain how to reset the control board as well as explain what might cause the issue and how to fix it.http://www.appliancerepairlesson.com/dishwasher-2/dishwasher ... Dishwashers

I need a diagram and fixing help for a miele G892 SCU plus. The dishwasher starts up with the intake draining light blinking and the saltpc light on. Then the start stop button turn green on. It sounds like it is filling with water but a few seconds it stops and turns off. I open and no water is filling. I believe it is the water pump, what do you think? How do I install it?

... Dishwashers

My GU2475XTVY0 built-in dishwasher has the "Normal" light flushing since yesterday morning. We pressed "Cancel" button, other buttons, and finally turned the power off and on, but it didn't do anything. Do we need to call for a service? It's less than 1 year old. Thank you!

Whrilpool Gu3600XTSB1 \015\012\015\012After a power surge the control panel pot scrubber and\015\012normal lights were flashing. I replaced the circuit board, thermal fuse and\015\012control panel. However, the lights are still flashing. what i ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Kenmore Elite dishwasher, model number: 665.17263. The clean green light is blinking and unit work work. I had this problem before and the service guy showed me how to press the buttons in a certain sequence which fixed the problem. It was the heating element.

All I had to do was to press the heatdry and normal wash buttons until all the lights went on. This happened before...Gingko was fantastic!! ... Dishwashers

Model mdb8959saso. Recent power failure caused cancel/drain light to blink rapidly. Only way to get it to run is by putting it in diagnostic mode and waiting for codes to stop.Do I need to call for service every time power is interupted?

... Maytag Dishwashers

Smeg df612sdx Until last week I enjoyed several years faultless service from my SMEG Stainless Steel dishwasher, with the exception of needing to replace 2 x spray arms. The unit has now stopped working altogether. Despite powering up several times, I continue to get both the start/pause and selection programs buttons constantly flash (green lights) when the unit is switched on; previously this only occurred once the wash cycle was complete. Any thoughts would be most appreciated. Thank you

... Dishwashers

I have just bought a cid60b10 dishwasher and it won't work! I completed the first wash putting water in the salt dispenser as instructed and when it had finished the wash there was still water in the bottom of the washer. Now when I turn the machine on all the buttons light up and then go off and I cannot select a function. Does anyone know how I can fix it without having to send for a technician?

... Dishwashers

After a power surge the dishwasher does not work at all. It just beeps constantly. There are no lights on the touch pad at all. The only thing that stops it from beeping is to remove the 2 pin black and white wires. I replaced the control module. Nothing changes. Do I need to replace the touch pad? What about the 3 digit clock? These parts together cost 145 dollars. I do not want to buy these parts and put them in to find out that did not fix the issue. I also unplugged the

... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

My power button cover broke on the dishwasher and I figured out the part number I needed, but when I put it back together I got the wires crossed on the board and door switch. Now the control lights up , but the dishwasher will not run a cycle. THe question is does the plug on the door switch have to be a certain way, because there are three wires and you can connect the plug both ways. I did turn the plug, but it still does not run. Did I break the switch? Bosch SHU9956uc/14

The wires do have to be a certain way on the door. Otherwise a door open can tell the board that's it shut and vice versa. The easiest way to do it, is test the switch with an ohmmeter, place the meter on the switch, push button in and see if the rea ... Bosch SHU9956 Built-in Dishwasher

Zanussi Dishwasher ZDT6053. Holding the On/Off button causes the indicator lights to work correctly, but as soon as you remove your finger from the spring loaded button, all the lights go off. Would guess that on/off button should electronically latch via the control board. Have removed mains power for 60 secs in the hope of a 'hard' reset, but no fix. Is there anything obvious to check or fix or must it be a replacement control board?

... Zanussi 23 in. ZDi6053SX Built-in Dishwasher

Put dishwasher on and 3 hours later went to unload. opened door to find END light had not come on and both 55 degree buttons were lit (I'm sure I only depressed middle 55 degree button button), 65 degree button was unlit. There was still some water in the bottom of the appliance. went through the procedure in the manual but cannot change the current state of the appliance i.e. the 2 lights on. HELP PLEASE! Model is TECNIK FD7811

... Tecnik Dishwashers

Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che

... Dishwashers

The start button on KitchenAid model #kudp01flbl6 will not engage, although all of the other lights in the control panel light when pressed. The cancel button will turn off the other lights in the control panel as well. This diswasher is 5 yeras old and lightly used in a household of just 2 professional adults. I've had service come and he uncovered a "burned' conection in the electronic control assembly p/n 8564542, which looked to me to be P8. A new electronic control panel was installed

HI. I need you to clarify somethign for me. You mentioned that you have replaced the " electronic control panel". Are you reffering to the interface board or the actual plastci panel? I understand that the part number "8564542" in in reference to the ... Dishwashers


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

The Start button does not light up, yet the left side did light up for wash cycles. I'm guessing the PC Control board has some issue with touch button panel, as a faint high pitched shrill can be heard from the board after I took the door off and put my ear to the board. Also, over time the left side of the panel stopped lighting up too, so I through the circuit breaker. Can you advise which component it is. I'm guessing the faint high pitched shrill is the PC COntrol board attempting to communi

You have a faulty touch pad that will need to be replaced. Below is a \015\012link to a video you will want to download so you can see how to replace \015\012the touch pad.\015\012\015\012\015\012\015\012 ... Haier ESD400 Stainless Steel 24 in. Built-in Dishwasher

Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than

... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher

KUDP01ILBS6 Kitchenaid dishwasher Doesn't work, except flashing lights on front panel. I have the normal light flashing. When I push any other button the cancel light starts blinking as well. I replaced the fuse, the main control board inside and it still doesn't work. Push button panel next fix? This is getting expensive. Could it be something minor? The troubleshooting papers didn't provide much guidance.

The first thing I would check is if the dishwasher is properly connected\015\012 to power input. There is a junction box under the dishwasher. To get \015\012access to it you have to remove the bottom panel. The power cord should \015\012be connected ... Dishwashers

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons

... KitchenAid Dishwashers

Child Lock light glows without pressing Energy Saver Dry button for four seconds. Cannot turn off by pressing Engery Saver Dry button for four seconds. Turning off main power and turning back on doesn't solve problem. But turning off main power for extented period, over night, and turning back on does fix proble for a very short period but Child Lock does come back on by itself. Is replacing the Console Assembly the only fix? Is there some button sequence to disable Child Lock altogher?

The mini manual for this dishwasher is located behind the kick plate. The mini-manual reveals that the child lock (called a control lock in the manual) can be disengaged by pressing and holding the air dry button for four seconds.or ene ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

Dishwasher will not start when pressing the start button. Timer light flashed numbers and went off. None of the lights and buttons work. Circuit breaker in electrical panel is working. Does the on/off switch need replacing, or is it possible a mini circuit board is bad? Dishwasher installed in 2000 and is used on the average once per week.

As it is nearly 10 years old i would suggest you replacing the circuit board. To test exactly we would need the help of an continuity tester and multimeter. ... Bosch 24 in. SHU53 Built-in Dishwasher

The on off selector switch on my Blanco d/washer BFDW 670S no longer works unless I stand with my finger on the button at which point the light comes on and the dishwasher swings into action. Apparently I need a new selector switch at some considerable cost and delay (not in stock from my supplier). Any other suggestions? Once the light is on, everything works as normal but the button just won't stay depressed. Thanks, Jan

... Dishwashers

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!

... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My Whirlpool Gold Quiet Partner III dishwasher will not start. I have installed a replacement control board that worked for awhile. When it quit I put the old control board back and it worked for awhile with a portion of the lights on the control panel lighting up. After switching control boards back and forth, it will not work at all now. It will run through the diagnostic program (Normal, Heated Dry, Normal, Heated Dry) but after that the start button plus other buttons are not lit so it will

... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1649 seconds