Having problems with your Whirlpool Dishwashers ?

Our whirlpool ADP 6565 dishwasher stops very close to but short of the end of the cycle, with the on-button flashing. If we press that button for a few seconds, it starts again and completes the cycle. I have cleared the filter on the inlet hose because we use tank water which does have particles in it frm time to time, but this made no difference.


Answers :

It appears that you have a timer malfunction. at the point that the timer stop, you need to listen closely to any sound from the timer. if no sounds emerges, repalce timer
Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our whirlpool ADP 6565 dishwasher stops very close to but short of the end of the cycle, with the on-button flashing. If we press that button for a few seconds, it starts again and completes the cycle. I have cleared the filter on the inlet hose because we use tank water which does have particles in it frm time to time, but this made no difference.


It appears that you have a timer malfunction. at the point that the timer stop, you need to listen closely to any sound from the timer. if no sounds emerges, repalce timer ... Whirlpool Dishwashers

I have a new LG Dishwasher LD120W1 purchased on 6/11/09. Have only used it approx 3 times. When I turned it on today it started up and after a few minutes it starts whistling and does not fill. Have looked at filter and spray arms, all clear. Could you please advise what else to do or look at. I can pull it out to look at hose it was installed by a plumber.


Hi,I would Glad to tell you what needs to be Done!! But, as the Dishwasher is Under Warranty, give them a call. Why to spend any Money, when the washer is under Warranty :) Now, It sounds like a Water Pressur ... LG Dishwashers

Vulcan Dishlex Executive 14-10 Dishwasher leaking onto floor from right hand side when it was filling at start of cycle. Husband has checked the following: both pumps (main and waste) hoses, solenoid switch (inlet). Where can we find the float/level valve? Could this be the problem? What else to check? This is the second time it's happened - I don't use it that much. The previous time my husband replaced the inlet and outlet hoses. What is the proper level for water fill - never above the


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If you have water leaks around the base of your dishwasher,\015\012you may be using a detergent that is ... Dishwashers

I have a Kitchen Aid KUDS03CTSS3 dishwasher. Dirty water is staying at the bottom and nothing comes out the drain hose during the entire cycle. The drain hose is looped above the kitchen P-trap, although for a time it wasn't. I use a wet vac to get the water out but there is still water below the fine filter. I thought if I could get the fine filter off, I could clean out the bottom as I think that it's full of crud down there that may be blocking things. I can't figure out how to get the l


Hi,Thanks for the follow up. I am glad it worked out for you. If I can Help in the future let me know. http://www.fixya.com/support/c64627-kitchen_aid ... KitchenAid 24 in. KUDP02FR Built-in Dishwasher

Meile Incognito won't start cycle. Lots done already; Basket, elbow, hoses, filters, & flows clear...Now What?


... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

I can not get the water to drain during a normal wash cyclr. When I press the start/restart button twice it makes noise but no water comes out the end of the drain hose. I have put a shop vac on the end of the hose and can get water out that way but it appears not to be pumping. The washer sits for up to 6 months at a time without being used. Thanks for any help Ted Berry Placencia, Belize Central America


Teddy,\015\012\015\012Buy a new one...then go fishin!\015\012\015\012Richard Vantine (ret'd Colonel...USAF) \015\012Bingelrade, The Netherlands ... GE GSD5310D Dishwasher

DD601ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the s


Check for restriction in sump. ie remove rotor, push pipe cleaner or similar from filter sump into rotor sump ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Dd601 ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the


I had the problem with the top draw not draining properly and the dishwasher showing the U3 fault code on my DD601 v.1, I did'nt have a copy of the dishwasher manual so it took the following steps, this is best done out side to save on messing your k ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My Kenmore Ultra Wash, type 575D does not drain after completing all cycles. I can get it to drain by pressing the cancel/drain button a couple of times. I have checked the filters and they are clean. What could be the problem? I believe the unit is only about 4 years old and it doesn't get over-used. Thanks. Jim Seibert


HiDishwasher not draining issue usually occurs due to kinked drain pipe, clogged drain filter or drain pump. Please check that the drain pipe, pump or filter is not kinked, clogged ... Kenmore Dishwashers

My SE53200GB/01 fails to input water. I have checked the inlet supply hoses and filters and they are clear. I have tried different programmes and they all activate but the water fails to enter the main chamber. Any ideas what may be the problem. Could the Aqua-Stop mechanism have kicked in and if so, how do I rectify it? Thanks


Your aquastop system is activated :deactivate by turning off the water supply, running the dishwasher so \012that it is expecting to fill (if you hold the grey square box at this \012point, you should feel it slightly vibrating, which is a good sign ... Siemens Dishwashers

My haier dishwasher won't drain. It's new ( used 3 times ). It has never drained properly according to mother in law. Didn't drain last night ( no dish cycle ) , pipes and filters all clear of debris.


Two things that you can try. One is to get a wet and dry vacuum and hook it to the drain hose and see if you can vacuum any water out. You should be able to. The other thing is to see if you can force water in with a garden hose. If memory serves me ... Dishwashers

I have 2 Viking VD141 Both DW are not getting enough water. They run and the soad dispenser opens but Their is very little water if any....I have taken the hose off and it is clear (no clogs) I have viking DW and Duel fuel Range. All of these appliances have been terrible. I have had service at least 2 times a year on both the DW. I use my oven in the basement as the range. takes FOREVER to pre heat and over cooks every thing. Don't buy viking they s$%#


You don't say what happens after the dispenser opens.These units use very little water and thus need very little soap, you can only use powder no cubes or liquid. It uses less than a tablespoon of soap. Also use jetdry it makes a huge dif ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

Bosch Exxcel Dishwasher (Enr SMS53E12GB/01 FD 9002) bought in July 2010. Error code 15 and "Check Water Supply" light on at same time. Have checked in-line filter in tap connection and all clear, water pressure OK, no kinks/twists in supply hose. Any help would be greatly appreciated - I'll have to call Customer Service in the end as it's outside of my problem-solving ability, but would like to check whether there's a known reset or fix I can try before I call.


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Whirlpool ADG 7440 defaults to pre rinse cycle then beeps. The light above the start button flashes intermittently. All filters are clear and water inlet is not blocked.


... Dishwashers

No water delivered,or "spinning" of upper spray arm.Serviced @n year ago & worked very briefly. Spray arms & filter cleaned. Using a hose as water source to test.....spray arm isn't blocked. The problem appears to be water isn't being delivered to upper spray arms. What could cause this & how can I correct? Thanks for your time & response. Sincerely, Lee Ballard


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for\015\012using FixYa. If the dishwasher is not filling then it is w ... Avanti DW18 Built-in Dishwasher

The water is not draining from machine, although the pump is obviously trying. It doesn't sound quite right. Kind of a growling noise. It can pump water into tubs when experimenting with ideas, but can't pump hard enough to pump the water into the sink. This is all done with the hose removed so we could check for debris in the line. I've checked the filters and they are clean and clear. This is a used machine a friend gave me, and it's been working beautifully until now.


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Bosch 24 in. SMU40 Built-in Dishwasher

I have a GE GSD2000J01WW Dishwasher in a building with low water pressure. The inlet hose is 3/8" OD. The heating coil gets too hot and gives off a bad odor as there is not enough water at start up. Is there a way or a replacement part that can be used to change the timing of the heater and wash cycles, etc.? Thanks


... GE GSD2000J Dishwasher

Trigger gun does not function each time the trigger is pulled. The water supply is more than adequate, water inlet screen is clean, water pressure adequate, no kinks in hose, all attachments are clear and I am lost. Thanks


I have same problem. This is a fault of the bypass valve at the pump end. It has to be taken apart and serviced. ... Karcher G3025OH Pressure Washer

The "clean light" on our Kitchenaid KUDIO1FLSS flashes 7 times and I cannot clear the problem to allow the unit to operate. Is there a sequence, using the control buttons, to permit the unit to run a system check? I disconnected the power for 30 minutes but that did not solve the problem.


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Havnt used my dishwasher in 2 years on account of saving water. now when i push the start button some water flow into machine for a few minutes and then just stops. manual says to clean filters and drain pump but all clear. what is next plan of action?


Try pouring water from a bucket through the front. maintain the level. It should not overflow.Run a empty cycle. If there is a air block it will get cleared. ... Asko 24 in. D3120 Dishwasher

Does not fill with water. Program light on. seems to click on ok but won't work further. Door closed ok Power ok water inlet on, checked for blockage on strainer in supply hose,filters and arms all clear.


Hello &\015\012Welcome to FixYa\015\012\015\012The problem\015\012is with the water inlet valve that needs replacement. You can also test the\015\012valve before replacement, if the valve tests fine then the float switc ... Bosch Dishwashers

I used the air dry/control lockpress and hold. I have never used this button, and it got pressed. I do not know how to clear this button so that i can use my dishwasher again. Cancel does not work. How would I clear this button.


Press and hold the air/control button again or turn the power off to the dish washer for a few and turn it back on and it will reset back to factory settings ... Dishwashers

I have a Braun combimax 650--it is fairly new. It was working fine last time I used it, but this time, the dial that turns the machine on seems to be stuck. The little button for the pulse does work. I read the instructions, which said that this might happen when the machine overheats and to wait fifteen minutes, but it is definitely not an overheating problem and the last time I used it was weeks ago.I love this machine and now need to use it for quite a number of things--any help you can provi


... Braun K-650 CombiMax Foofs Processor FOR 110 VOLTS

Attempting to install asko d1706 dishwasher. Bought used, had no hoses with it. when trying to connect water inlet hose, unable to connect without leaking. Finally got a connection on there that has it slowed down to a drip. does the inlet valve need to be replaced or is there a special inlet hose that we don't have?


Yes there are actual dishwasher supply hoses you can purchase at most hardware stores.... if you do have the correct hose may try to put some teflon tape on connection so that leak stops....\012good luck to you ... Asko Dishwashers

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0920 seconds