Having problems with your Whirlpool Dishwashers ?

Whirlpool dishwasher adp 4731/5 showing f4 - Whirlpool Dishwashers


Answers :

Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Whirlpool dishwasher Dishwasher is showing F4 and not working. Whirlpool 6th sense ADP7966 its about 2years old.Also can not find this model anyway.


We had same problem with our ADP 5966. An engineer over the phone said he thought it was related to machine being unable to drain. I checked the drainage pipe connection to u-bend under sink, and sure enough, there was a major blockage. Cleared that& ... Whirlpool 24 in. ADP5966 Free-standing Dishwasher

Our LG 6810 dishwasher has stopped cleaning. After the cycle the dishes are wet and covered in greasy clumps. We ran the test cycle and got the following: 3H/U3 11 22 33 44 55 66 04-2 32 33 0 (inlet valve) 35 36 37 38 23 (Thermistor) 3A 3A (beeped twice and showed 3A) 3A (beeped twice and showed 3A) Any advice you could give me would be appreciated. I have the service manual but have never done any type of dishwasher repair. I'd like to not have to replace this dis


1.) Take racks out of unit.2.) put both of the spray arms in the 12 o'clock position3.) Run the washer,once the washer has started wash cycle,open the door and ensure the spray arms have moved off of the 12 o'clock position. Write down re ... LG LDF6810 Built-in Dishwasher

Whirlpool dishwasher adp 4731/5 showing f4 - Whirlpool Dishwashers


... Whirlpool Dishwashers

Dishwasher Whirlpool adg 6966, light showing 20 mins even 4hrs and more after finishing


... Dishwashers

At 2 minutes left in the wash cycle, the quick rinse light starts blinking and the timer goes to 0. My dishwasher is a Whirlpool Quiet Partner IV gu1500xtkbo dishwasher. I'm assuming the blinking light is an error code. What does it mean?


... Whirlpool Dishwashers

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

My Whirlpool Gold dishwasher "shuts down" after the first 2-10 minutes, leaving the Sensing light and the Water Heating light showing. Any suggestions? Also, the horseshoe-shaped metal coil at the bottom of the dishwasher is burnt-colored. When I touch it, it looks like black soot has fallen off of it. Thank you ahead of time for your assistance!


As you mentioned the coil is burned that can also be the problem.it has to be replaced.but also other possibility is faulty shut-off valve in the dishwasher makes the unit shut -off after certain period of time.\015\012----------------\015\012so chec ... Whirlpool Dishwashers

Whirlpool dishwasher model # DU1055KTP34--washer stopped mid-cycle---no power at panel---removed panel and checked door switches--one showed 5 volts and switched other showed line voltage and switched


... Whirlpool 24 in. DU1055XTP Built-in Dishwasher

Whirlpool dishwasher, model DU1050XTPQ1, type 575-0; problem: showing no sign of power to unit and bottom of dishwasher is full of water---it apparently stopped during cycle. Is there a reset button? I have tried depressing the front panel "lock" button for five to ten seconds to unlock the system with no luck. The washer is hard wired to the home electrical system. What should be my next course of action? Thanks


... Whirlpool 24 in. DU1050SS Built-in Dishwasher

Program shows shows f4 and peeps - Whirlpool 24 in. ADP6940 Dishwasher


F4 indicates DRAINING FAILUREdrain pump starts and after 4 minutes the OWI detects that mashine is 'not empty'posible mailfunction reasons:drain pump defective/blockedsiphon closedcontrol bo ... Whirlpool 24 in. ADP6940 Dishwasher

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

Whirlpool Dishwasher ADG 9020 showes error code F6. What does that mean?


... Dishwashers

I have a Bosch SHU9955US/14 (Integra) dishwasher. There is currently a 0 with and asterisk showing on the display and the unit will not run.


See this causes and fix it. God bless you\012 \012 \012 \012 \012 Thermal Fuse\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Bosch Dishwashers

The original control unit from Bosch' dishwasher SHU4302UC/14 has been replaced after recall from Bosch with a new one that stop working after three washes. It does not respond to any command and shows ''0'' at display. What may be the problem?


... Bosch 24 in. SHU43 Built-in Dishwasher

My whirlpool dishwasher is showing a F7 error code what does this mean ?


F7 error codes on whirlpool normally mean you have a bad control board.. ... Dishwashers

Whirlpool dihwasher adp 4552. Water comes into dishwasher, appears to start cycle then water is drained out again and light flashes to show a problem!


This is a typical anti flood activation due to the anti flood device (polystireen float and micro switch) at the base of the washer detecting a water leak / spill. This device puts the washer in pump out mode. Check to see if water at the base is cau ... Dishwashers

I have a GU980 (whirlpool)-- the dishwasher will show tha it is on sounds like it is running but no water is filling it.


... Dishwashers

Whirlpool dishwasher mod.ADP80 PC show error F6, feeding water is ok , filters are clean, another solution ?


It would be helpful to know how far into the cycle does the error show up.\015\012Also does it go away when you turn power to dishwasher off and back on.\015\012\015\012If you can operate the dishwasher then try in Rinse only and s ... Whirlpool Dishwashers

Whirlpool dishwasher wont show any signs of life. wiring is good...


Check the door interlock. Not sure but that is where I would start assuming you know for a fact that it has power. ... Dishwashers

F2 fault showing, what is this? - Whirlpool Dishwashers


Overflow sensor . Called out an engineer! ... Whirlpool Dishwashers

My Bosch integrated dishwasher(model SGV56A03 GB/12) runs through the cycle but doesn't stop at the end of the cycle. It continues to heat water and it sounds like the motor is running even though the time indicator shows 0 minutes. I have to manually switch it off. Any ideas before I call out an engineer. I have checked all the filters etc included in the troubleshooter info anf there are no blockages.


... Bosch Dishwashers

Whirlpool gu2500xtps6. The dishwasher was working perfectly but one of these days, for no apparent reason, it wouldn't show any sign of life. None of the LEDs on the front panel light up. It does not respond to any button being pressed. Looks like something electrical but all my circuit breakers are fine. Is there any fuse or something simple that I could replace myself?


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

6th sense whirlpool dishwasher not heating water or finishing cycle showing f3 on display dishes seem clean but not spotless and wet becuase they are cold


Check thermostat and heating elementwires and timer ... Dishwashers

Whirlpool Dishwasher Quite Partner II, 6 years old, Manual shows Models DU620, DU943, DU950, DU951, DU 960 and DUL200. Burning smell, clicking sound, Wash light blinks. Machine full of water.


... Whirlpool Dishwashers

I have a Whirlpool dishwasher GU1500XTL53 that has a sensing problem. When I start in "normal" or "antibacterial" the sensing light turns on and the unit constantly runs without a number showing up on the time left. Is there any fix to this? Thank you


... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1858 seconds