Having problems with your Whirlpool Dishwashers ?

No water going into dishwasher

\015 When you turn the dishwasher on no water runs in ,power is on and element heats\015

Answers :

Make sure the float is pushed down. it is usually a white round piecelocated inside the door on the bottom of the dishwasher on the right or left in the front..
Repair Help & Product Troubleshooting for Whirlpool Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have Frigidaire FDB956RBC1 diswasher. I have to turn off the water to fix the faucet. When I turned the water back on, water did not go to the diswasher when I used it. The diswasher runs normal except with no water going into it. The water runs find at the facet. There is separate water supply underneath the sink for the faucet and the diswasher. I wonder if there is a mechanism with the dishwasher that stop the water from going into the dishwasher after the water supply been turn off. I did


FRIDG... EXPERT HERE \012\012\012Welcome to fixya\012\012Hello\012\012 \012\012 ... Frigidaire FDB956RB Built-in Dishwasher

Water not going into dishwasher. We turned off the water temporarily because we first had a leak. Fixed the leak and tried the dishwasher. It would not drain, the garbage disposer was clogged. We put in a new garbage disposer, hooked up the water again to the dishwasher and now the water will not go into dishwasher. Help!


Is the drain attached directly to the side of the disposal? If so, you didnt take the "knock out" out. Where the drain goes for the washing, there is a block in case the house does not have a washing machine. U need to knock this out with a screwd ... Hotpoint 24 in. HDA2000Z Built-in Dishwasher

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

There is gum stuck somewhere in my dishwasher drain line. The water won't go down. I took the inside apart and can see the hole where the drain water goes. I disconnected the drain hose under the sink. I got the water to drain out when there was alot in there, but now it won't drain again. I blew compressed air from a compressor backwards through the hose and it makes a big splash and bubbles inside the dishwasher, but the water still won't go down. I put Boiling hot water and vinager in there t


Ther e is noo easy fix, short of replacing the drain line( if indeed thats where the clog is)although you checked the hose from the under the sink, did you check with in the hole where the sink conection is made??and try disconnecting the drain hose ... Dishwashers

I was replacing my sink faucet today and in the process turned the water off to the dishwasher. Subsequently my girlfriend ran the dishwasher without the water on! Now when I go to run the dishwasher no water comes out (meanwhile I've turned the water to the dishwasher back on). Is there some kind of reset? I accidently touched the coil in the bottom of the dishwasher just after trying to run it and it was hot. What do you recommend? Thanks. Mark


Hi,You need to investigate the following :-\015\012\015\012\015\012\015\012\015\012Drain line/air gap\015\012\015\012A\015\012clog in the drain line or air gap (if there is one) is the usual reason\015\012that a dishwas ... Kenmore Dishwashers

I have a ge profile quietpower 7 dishwasher. its built in.cannot find manuel and cannot find the serial number anywhere on the dishwasher..i need either your help with serial number or help with why water will not go into the dishwasher. motor runs water decided it wont go in. one day worked perfect and next day stopped working.


Hi\015\012\015\012This is often caused due to the fill valve. You can ... GE Dishwashers

Hi I have a Nemo Dishwasher and the top spray arm is not turning. The bottom one is going fine and there is certainly plenty of water getting into the washer as I opened the door with the washer going and it flood me. I can see the water getting into both spray arms - the bottom one has a excellent upward spray and turns - the upper spray arm has water getting into it but it will not turn. I have cleaned the dishwasher out and any internal parts that I could find so it is spotless - this is so f


... Fisher and Paykel DS602 Dishwasher

Dishwasher Repair I have a Frigidaire dishwasher that came with the house. The house and washer are probably about seven years old. It woked fine for the first few months but now, when I turn it on to wash it fills with water but then it will not go into wash cycle (i.e. there is no water sent into the dish compartment). It will go through every cycle by filling and emptying through wash and rinse but no water goes into the dish compartment. Is there a pump that is perhaps not working? How is th


Ebers, you have a seperate wash and drain motor on this model. When you remove the bottom panel the drain pump will be on the right and the circulation (wash) pump will be in the rear. You are going to have to verify that you have power getting to t ... Frigidaire 24 in. FDB421RF Built-in Dishwasher

Dishwasher Water is not going through upper and lower spray arms. Checked overfill protector switch, inlet valve, inlet valve screen, pump blades move freely, Pumb motor is working , Water enters into machine but does not go throught spray arms. Water heats up, Machine will go through all cycles but without water going through spray arms. 650 / 690 series gldb656jso


... Dishwashers

Portable Dishwasher Hello, We just got a used Haier portable dishwasher, model HDP18PA and while the hose connnects fine to the sink, the water isn't going into the dishwasher and is coming out of the connection. Does that make sense? It looks like, if it operates properly, the water should be sucked into the dishwasher but the connector isn't pulling the water in. Help! Thank you! Tara


You have to have a good seal. Get a hose washer from your local hardware store and replace both of them on the hose if they are like a garden hose. If you still don't get any water to the unit, post again and I'll step you through it. ... Dishwashers

Dishlex DX102 How do I get access to the impeller. I have broken down and cleaned everything from inside the dishwasher, but the water still does not pump away. It pumps in water okay, but not away. How do I go further, the last two screws drop the whole unit down, do I have to pull the dishwasher out and go thru the front kick panel?


Your outlet path is most likely clogged with food, the remains of paper labels, or a combination of both (assuming the sealing plug was not left in your disposer unit). I've taken lots of these apart and they are all slightly different. Hopefully y ... Dishwashers

Water dose not go into dishwasher, it will keep running but no water is going into the dishwasher at all.


Make sure water is available to dishwasher. You will need to remove the front lower panel, and SLOWLY loosen the water supply line to the dishwasher. Place a shallow pan under the line to catch the water. \015\012\015\012If water is pre ... Dishwashers

Dishwasher does not water to come go past inlet solenoid. I have checked pressure to value and it is good. Looking for part but having problem accessing parts store. when we turn on dishwasher it sounds like it is starting but there is no rush of water sound at the vent going to the garbage disposal like it used to. And then it errors out/stops.


... EuroTech 23 in. EDW254E Built-in Dishwasher

Water is not going into my dishwasher --worked for 13 months fine and now having a problem. When I turn it on the motor runs and rattles - louder than before, but no water is going into the dishwasher. We did nothing different and have not changed anything.


Try running a diagnostic run on the washer. Push heated dry, normal, heated dry, normal on your cycle selection panel. After you push that sequence all the lights will light up and then it will go through a test run. This fixed my washer that had the ... Whirlpool DU1055XTS Built-in Dishwasher

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Model No. DU850SWPU3 AND SER. FT 4101406 TYPE 280-0. When cycle is complete and in off position the dishwasher fills with water. I find the bottom of the dishwasher standing full of water when I get ready to fill with next load of dishes. When I remember to turn off the wall switch this does not happen, however once in a while I forget to turn off the wall switch. The next day I find the bottom of the dishwasher full of water again. I then have to go through the cycles manually a couple of tim


If by turning the wall switch off, and only then it stops comming in, it means the board is faulty. There is a leak in the electronic system allowing to solonoid to stay partially open. Strangs that it doesnt flow onto the floor. ... Whirlpool GU2400XTP Built-in Dishwasher

Dishwasher confused Dishwasher was switched off just after cycle commenced (tablet had been released). On restarting dishwasher, it wouldn't take in water and has just been going through the motions of the cycle without anything happening. Even when the power button on the machine is switched off or the door is opened, the motor continues to run but without water. Water is definitely switched on under sink. I think the computer is confused - can you please help?


I suspect this is nothing to do with switching off during the cycle.take the bottom plate off and check if there is water leaked into the bottom pan. alternatively, if you can, tilt the machine back to 45deg and see if water runs out.most ... Dishwashers

Whirlpool dishwasher doesn't seem to fill with enough water despite good water pressure. Therefore, pump sounds like it is cycling from pumping water for about 2 seconds to going dry for 2 seconds to pumping water for 2 seconds to going dry for 2 seconds, etc. Spray arms rotate only for the 2 seconds when pump is actually pumping water. Dishes do not get clean.


... Whirlpool 24 in. GU2548XTPS Built-in Dishwasher

I have a Bosch dishwasher model #SHU3032UC/U12 It is not pulling water from the water pipe to wash the dishes the motor wants to go thru cycles. It starts to pull the water by the sounds from the sink but no water gets into the dishwasher.


Hello. When no water is entering the dishwasher, there are two parts to check. \015\012Water-inlet valve\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012The water-inlet valve lets water enter the machine. If this ... Bosch Dishwashers

Candy CDI1012 Integrated dishwasher. When I turn on the dishwasher and start it - for some reason it can not go the whole way through the cycle. When I open the door the - programme light is flashing and water is still in the bottom of the dishwasher - ie mid cycle. The water will only drain if I put it into another program to drain away - but as the dishwasher was mid cycle - the dishes are not clean


Hello mm1973,It could be because of bad door latch switches / blown thermal fuse / blown or oversensitive control board. In all these scenarios, a dismantling of the machine is required. If you have no prior experience, I'd recommend get ... Dishwashers

My trusty Bosch s510 Dishwasher which has been going strong for about 17 years (at least) has just decided not to empty itself. I noticed the bottom was full of water after a wash. I emptied all the water out by hand and presuming there is a blockage in the drain tried using a plunger to unblock it. I have since put it through another cycle and half way through water started leaking out of the front. At the end of the cycle the bottom of the dishwasher was again full of hot 'soapy' water. If th


Same problem, so went out and bought a new bosch. Problem with the S510 was cured by lubricating the pump out motor bearings with a squirt of WD 40. If you don't know which pump, follow outlet hose to pump outlet.Les ... Bosch Dishwashers

I have a Bosch SHU9915UC/U11 dishwasher, installed in 2002. Recently, our hot water heater had to be replaced, and we were without hot water for five days. Air got into the hot water pipes, and dried out all the debri in the lines. When we got the new hot water heater going, all of the sediment in the pipes ended up in the in-line screen filters in various appliances (clothes washer, etc.). I have cleaned these out, and these appliances are fine. Since then, the dishwasher has been shutting


All inlet valves have a screen built into the valve itself,shut off the water remove the entire valve and you will be able to see built in screen,if you flush out the debris from it and re-install the valve it should work fine.  ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have a Frigidaire dishwasher and there is not any water coming out of the top wash arm. There is good water pressure coming out of the lower washarm. I pulled out the dishwasher and can see the water going to the top washarm through the tube and it goes up very slowly. I took out the "check ball" below the lower washarm and it worked good. I put the "check ball" back in and ran the machine on "Upper Rack" and it still does not have any water coming out of the upper washarm. It doesn't seem lik


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check that there is no gunk or mold\015\012behind the filter screen and under the cover at the bottom. N ... Frigidaire PLDB998A Built-in Dishwasher

My zanussi fitted dishwasher is leaking water through the door. removed front panel to see what is going on and the water is spurting out of two gaps in the seal. the seal is brand new and manufactured with these gaps. is there too much water in the dishwasher - does it have float valve that could be at fault?


It has a pressure stut,that should tell it to stop filling the machine,it sounds like it has gone ... Zanussi 24 in. ZDT6041 Built-in Dishwasher

My dishwasher only fills half way and it dosn't go through the wash cycle. It pumps the water out and then go to the rinse cycle but has the same problems with the water level. We have checked the motor, pump and the water valve. It seems to be working fine. Thought it might be the timer.


Hi,\015\012\015\012This is an issue with the wash motor..\015\012There are two motors,a wash motor and a drain pump/motor assy\015\012The wah motoe must have been the issue with the case.Changing the wash motor will solve your ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1807 seconds