Having problems with your Whirlpool DU1055XT 24 in Builtin Dishwasher ?

Pots/pans and normal cycle lights flash alternatly...soak/scour light on continuously. dishwasher does not work at all. did disconnect power for 12 hour. lights come back on flashing, still no function.


Answers :

Repair Help & Product Troubleshooting for Whirlpool DU1055XT 24 in Builtin Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Pots/pans and normal cycle lights flash alternatly...soak/scour light on continuously. dishwasher does not work at all. did disconnect power for 12 hour. lights come back on flashing, still no function.


... Whirlpool DU1055XT 24 in Builtin Dishwasher

Normal light is flahing unit will not go on sometimes time remaining indicator will flash started awhile back by not being able to change any settings but unit would work now nothing have tried disconnecting power still nothing


HiIf clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Hi i have a problem with my bosch dishwasher model no.5600 061 333 en(8311), there is no power light and not functioning with any mode and when plugged in it makes a big flash sound from underneath. The plug fuse is still intact. The plug has also melted the plastic backing plate when plugged in. Could you tell me what the problem is and how to go about fixing it. Thankyou.


... Dishwashers

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

Power button is flashing and 12 is flashing in the panel, have switched of at mains and it then takes ages for power and same symptoms to come back after turning on again, anybody any idea what the 12 means. tia


... Hotpoint-Ariston LFT 228A 23 in Builtin Dishwasher

I have a Frigidaire Gallery dishwasher model number FDB989GFC2. All of the indicator lights on the right side are flashing (Controls lock, add-a-dish, washing, etc.). when buttons are pushed I get no response. Have tried turning off at circuit breaker for 1 hour, when powered back all lights still flashing and still no response from pushing buttons. Any ideas?


You need to rpelace the electronic control board ... Frigidaire FDB989GF Dishwasher

I have a KitchenAid dishwasher, model KUDP02FR. The "normal" cycle light is flashing. When I push "cancel" or "resume/start", they start flashing as well, but the dishwasher won't start. I turned off the power and turned it back on. The "normal" light still flashes, but when I press "resume" it all starts over again. Any ideas? I can't find this in the troubleshooting guide I have. Thanks.


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid KUDI01TBK Dishwasher

Normal light flashing on and off. Pressed cancel, now both normal light and cancel light are flashing. Dishwasher won't start. Can't shut lights off. Tried disconnecting power. Lights still flashing.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. To resolve this you will have to\015\012reset the console. Do this by closing the door and press t ... Dishwashers

I have a Whirlpool dishwasher model #DU920PFGQ4. The controls locked light is flashing, and when I press the air dry key for 5 seconds it won't unlock, however the cancel/drain light starts flashing. When I press the cancel key the controls lock light will stop flashing, but will resume as soon as I release the cancel key. I have tried disconnecting power for 24 hours, but as soon as I plug it back up it does the same thing. Nothing else on the control panel will work.


... Whirlpool Dishwashers

My kenmore dishwasher, model 665.16473300 has stopped working. Now the lights just flash at the Smart Wash, Normal Wash, and Cancel. I've reset the power and it just comes back. I've taken the drain area apart and made sure there are no obstructions. The buttons seem to respond, as after I reset the unit (breaker), only the Smartwash button is flashing. I push cancel and then it starts flashing. So I think the buttons work, but it's locked up.


IS THE WATER TURNED ON TO THE DISHWASHER ... Dishwashers

Kenmore elite clean lite is flashing won't shut off.unit won't work modle #66516912001 serial#fk4402228.it flashes 7 times over and over.i shut off all power turn back on still flashes .i replaced electric board in door panel new button panel


I have a service bulliten on this if you will email me at [email protected] ill send it to you its too big for here ... Dishwashers

The "Normal" button light keeps flashing. The door had come open during a wash cycle and there is still water in the bottom of the dishwasher. I've shut off the power, but the light still blinks. Model is KUDSO1FLSS6


The washer had been interrupted during the program cycle and so the main micro controller has hung up. You can remove off plug for few hours or iover night to reset the processor.\015\012Now make sure that the door latch is clicking and contact ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

How do i reset a fisher and paykel dishwasher model dw920. Code F1 appeard found out i had a blocked drain, fixed it but still beeps and flashes F1. Have also disconnected power from mains but still the same. Thanks David.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You\342\200\231ll need to reset it by p ... Dishwashers

My Dishwasher starts, then stops after 30secs and won't continue draining. Everytime I turn it back on it comes up on the steam cycle and won't go to any other cycle, drains for 30secs and stops again. Power light is flashing. Have tried holding power button down for 10secs with no effect. Filter is clean, pipes are straight-no kinks. How do I get it to start working again? It is a whirlpool dishwasher, ADP5550.


... Dishwashers

Dishwasher will not reset after power being off. C1 displayed, often, it shur down due to water in bottom. Cleaned hose, power back on, PF STILL FLASHING.


PF is Power Fail.Means there was a disconnection from mains power, without turning off. Do so & reconnect and turn ON again.\015\012C1 = Partially restricted drain, pump-out not accomplished in the normal time of less than 95 seconds\011 ... Dishwashers

I have a Frigidaire FDBB944CSO, It was working fine but one day the power went off and when the power came back on it just started flashing Hi Temp Wash and Dry Heat Off. I tried resetting it but still the same thing.


... Frigidaire 24 in. FDBB944C Built-in Dishwasher

Hotpoint dc27, once the wash is finished the drying light should come on flashing but it goes back to the wash and then flashes but when i look inside it hasnt done the last bit of the wash and its still dirty, any suggestions?


... Hotpoint 18 in. DC27 Slim-Line Built-in Dishwasher

My electrolux dish washer model eidw6105gso stopped before it completed the cycle. All the selection lights were flashing and i could not get any functions to change. I killed the power at the breaker to try to reset and that didn't work either. I removed the panel on the front on the bottom to see if there was a reset button and found another display that is showing a light on the turbidity location. what is this and what might i do to get my washer back working?


... Electrolux Dishwashers

The accu sensor flashes 'clean' with dirty dishes and the washer doesn't start.I shut the curcuit breaker off for a while and when turned back on, the 'clean' sensor still blinks and the washer did not come on.


... Whirlpool Dishwashers

I have a Kenmore dishwasher model 66574362K2. It has worked fine until tonight. I opened the door before the end of a cycle, closed the door, and pushed the cancel drain button. There was still water in the bottom but the dishes were basicly finished. Now I can not seem to get the dishwasher to come back on. The lock button seems to be on and it usually is not on. The manual says to push and hold the button for 4 seconds to turn it off. I did that. But now it is flashing between the Heate


Can you press the drain button to drain the water, then shut the unit off and restart??? I have exhausted all my resources to help, thought this may work. ... Kenmore Dishwashers

Miele g892 scu plus, about 5 years old. when on, all it does is run some motor (humming sound) and flash salt or intake/drain. No program lights on. Sometimes can be reset so rinse light comes on and nothing blinks, but humming motor still runs and salt eventually blinks. I removed toekick panel; there is water in pan. I disconnect drain hose, only a little water came out. Any ideas?


... Miele G892SC SS Dishwasher

Error 91 displays on the panel and after turning off breaker, the error still comes back and eventually displays a flashing ER and none of the keypad buttons respond


... Frigidaire PLD4375RFC Dishwasher

Lights on the control panel flash. Dishwasher does not come on. Tried reset and turning the power off. Problem still persists.


... GE Nautilus 24" Built-in Dishwasher

I have a LG Dishwasher LD 14AW3 it fills and runs for about 30 min. It then appears that when it tries to rinse it cannot get water and flashes "1E". I disconnected the unit and when I moved it out of its position water was leaking from the bottom of the unit. after cleaning out the inside filter & the hard water filter I re-connected and found it worked. I ran a dishwasher cleaner through it at high temp. After a few loads the problem has come back. It is now located in MY garage waiting for me


Found a leaking component that was causing the foam float located and attached to the inlet valve to shut down the water inlet and the water inlet Solenoid was also sticking. I found out this simply by tapping it while it was trying to get water for ... LG Dishwashers

I had a black out and the dishwasher was running at the time. The dishwasher emptied out all over the floor. when the power came back on the dishwasher was flashing an error code 4. I rang Whirlpool for assistance and they said it was over full but it was totally empty. We turned the dishwasher off at the wall hoping it would reset but it is still saying error code 4. Can you suggest something else we can do?


The trouble looks to be little confusing. Whenever the power failsduring mid cycle this happens. Try running the balance cycle. Since you say the water is fully drained, try adding water manually tothe wash chamber to certain ... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1624 seconds