Having problems with your Whirlpool DU1055XTS Built-in Dishwasher ?

My whirlpool dishwasher cleans well but once the rinse cycle is completed and drained the next day the washer has water in it. HELP!


Answers :

It could be a bad fill valve.to chk this ,open the door and look for the inlet hole from where water comes in.if u see and droplets of water coming down the hole then it is the fill valve.when machine is off the fill should be closed and no water should come in.
\015\012other thing could be ,if u have hooked up the drain pipe of the unit directly to the food disposar instead of going through air gap mounted at the sink then some water from the disposar could flow back into the unit.units have chk valve valve built in drain pipe but some times they work 100%.also chk 2 c if water insinde unit is dirty or fresh to confirm above things.
Repair Help & Product Troubleshooting for Whirlpool DU1055XTS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My whirlpool dishwasher cleans well but once the rinse cycle is completed and drained the next day the washer has water in it. HELP!


It could be a bad fill valve.to chk this ,open the door and look for the inlet hole from where water comes in.if u see and droplets of water coming down the hole then it is the fill valve.when machine is off the fill should be closed and no water sho ... Whirlpool DU1055XTS Built-in Dishwasher

Dish washer does not drain after the cycle is complete. The last few months when the dishwasher is done their would be a small amount of water left in the bottom. It didnt create any problems but would smell after a few days. So we would just run the drain cycle and it would empty. Well i got home to and the wife said the it was really full. The water was dirty and when you run the drain cycle it didnt drain. She said the dishes were clean. So i cleaned the vent, and filled the sink with


Check drain hose and drain pump.End of drain hose must be in same level with machine.Try it. ... KitchenAid KUDR01TJ Dishwasher

My bosch dishwasher runs fine, cleans fine, drains fine....but after it has been just sitting for a while, the bottom very slowly fills up with water. Each time we run the machine the water level drains back to the normal amount in the bottom of the washer after the cycle is complete. The problem is if we are away for a few days, the bottom fills up and overflows onto the floor.


Water inlet valve isn't closing all the way closed. Need a new one ... Bosch 24 in. SHU53 Built-in Dishwasher

Kenmore Ultra Wash Quiet Guard - will not drain at end of cycle. After cycle is complete, water (not clean) sits at the bottom of the washer but I still unload the dishes and then turn the cycle dial around again - going past all the water heating and filling and washing - and land on the drain cycle, it will drain. Any ideas why it will not drain when I let a cycle run, but will drain once I cycle it through to the drain option?


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

I have a Bosch "Classic Electronic" dishwasher that has been in use for only 18 months. If it helps - SGU53E05AU/30 is marked on top of the door.. my problem is that on the last cycle, the water won't drain so I am left with lovely clean dishes but there is water up to the drawer line present and it won't drain until the next wash. I have cleaned all the filters and ensured the pipes are not obstructed. It is odd that it only does it on the last cycle. Could it be the microchip?


Hi there,\015\012\015\012thank you for providing the model #, that helped me narrow down the troubleshooting.\015\012\015\012try the following to fix your problem:\015\012\015\012check for blockage or kink in the d ... Bosch Dishwashers

I have model 363.14779100 that has a problem. When a drain cycle is at the end and the fresh water starts coming in, the draining won't stop therefor all clean water goes right back out the drain. I can open the door latch and reshut it and the cycle will complete but the same thing happens on the next drainout. Is there a switch that needs replacing??


... Kenmore Dishwashers

Ge model # gsc3200j01ww dishwasher. when the door latch is closed, nothing happens. motor does not start. if the timer is advanced to the next part of the cycle, water will spray into unit until float valve is triggered. water will not pump out, motor does not start. bailed out water, checked for stuck float valve-ok. removed drain screens and filters, cleaned. no motor, drain, or start. what parts should i check? always rinsed dishes before putting in washer. unit is portable or undercounter


... GE 25 in. GSC3200J Built-in Dishwasher

Water drainage I have followed the manual instructions for clearing all appropriate filters on the intake and outflow side but the cycle does not complete and leaves a pool of water in the base. What next? I have the G568/858 Plus Incognito unit (thisis the closest part # to my actual unit--can't even find teh right # listed...), and aI m dealing with the sme issue. I have followed all of the recommended steps in cleaning the filters, traps, etc. There are no kinked hoses. The water drains to b


YOU NEED TO REMOVE THE LOWER SPRAY ARM AND REMOVE THE SHELL THAT IS COVERING THE PUMP AND FOOD SHREDDER ,HERE IS WHERE YOU LOOK FOR A CLOG. ... Miele 24 in. G892SCU Plus Built-in Dishwasher

Does not clean the dishes... detergent tabs are undesloved when cycle is complete...i can hear the water and feel the steam so i know water is going in and out BUT i ran the same load 3 times in one day and forks where grimy and glasses where oily...please help


Run at the higest temp it wikk fix the prob ... Bosch 24 in. SHU43 Built-in Dishwasher

Have SHU43C and have had no problems with it. We usually run it on the Quick Wash cycle, but ran it on the Regular Wash cycle yesterday because the glasses seemed to be coming out spotty. After it ran, there were no lights on the display like there usually are. The washer had run and the dishes were clean, but it has not drained completely. There is still about an inch of water in the bottom, despite removing and checking both the Large Object Trap and Fine Filter (neither which were clogged


The drain pump needs to be replaced or cleared of obstruction. ... Bosch 24 in. SHU43 Built-in Dishwasher

Kenmore elite 2 front loading washer model#110.45872400 It first flashed the code FH and then went to the running time is now flashing and it sounds like it is running but the cycle never starts and I cannot cancel the cycle by pressing pause/start two times. I have checked the water lines and the screens and cleaned out the drain catch below. what next


... Kenmore Dishwashers

Neff dishwasher our dishwasher is six years old and have had no problems till now . there is power to it but when you push the on button the impeller starts up even when the door is open , and it wont go through the cycle , its asif there is no water going in and it is not draining away i have checked and cleaned the filters but nothing, then pulled it out from undre the sink and it started working . i put it back , it went through the cycle then the next day it would'nt work again . do i need a


You have a faulty door switch. It can be replaced and may be available at youre local appliance parts dealer. ... Dishwashers

After wash cycles are completed there is about 1/2 gallon of water remaining in the bottom of the washer. I checked the drain that exits into a disposal and that is clear. All around the bottom of the washer base is clean and I can find no obstruction. Nothing in the owners manual gives me a clue as what else to do. I don't want to start taking things apart unless I have to.


Hi and welcome to FixYa. I am Kelly. Most dishwashers are connected to the sink / garbage disposal via an Air Gap. The Air Gap gets debris inside it that blocks the drain passages. Check out this video on how to clean it: ... Maytag 24 in. MDBH950AW Built-in Dishwasher

Large amount of water remains in tub after completion of wash, water is draining out during cycle, dishes are cleaned, I can hear water being pumped out into sink drain as dishwater is going thru its cycle. The depth of the water is over one inch at the lowest part of tub. Water is not clean and has soap in it.


Hi.To start check the drain well, and also have a look at the drain hose at the back of the appliance.If the drain lines are OK, then you will need to replace the pressure switch, that determines when to stop pump from drainin ... GE Dishwashers

Hello, I had a problem with my Bosch dishwasher not washing properly. I have fixed burnt out wires, replaced the water inlet valve, AND tested with a new control module. Nothing is helping. When I start the cycle, it completes the initial drain and water does flow into the unit for about a minute, maybe a minute and a half. I can hear the clicking of cycle changes but it is not washing. Eventually it will drain the inch or so of water in the bottom, but it never washes. Any help???


Hi,\015\012\015\012Welcome to Fixya.\015\012\015\012Can you hear the wash motor humming ? I`ve got a "pdf" I can send you regarding this if you want to contact me at ... Bosch SHU9925UC Built-in Dishwasher

Drying problem Hi Our 3-day old LG dishwasher is not able to dry our dishes. After the cycle is finished 2 hours later, I open the door to find that water is everywhere. As if the washer is skipping the dry sequence completely. The "vent" on the inside of the door doesn't seem to have an outlet--why is this a vent if nothing can escape? The owner's manual says to use a rinse aid to help drying. I don't believe in using band-aid's; something else is wrong. Any help/advice is appreciated. Thanks,


Hi,\015\012\015\012As I had the same problem, I worked on my machine and found out the heater unit was not working (it is a brand new machine ! - remark : as I moved overseas, LG did not cover it with their warranty).\015\012\015\012But b ... LG LDF6810ST Stainless Steel Built-in Dishwasher

My dishwasher won't drain completely in the last cycle so in other words water remains in the bottom of the washer. Don't know how to take it apart and clean out.


\012Hi,\012Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... Dishwashers

Magic Chef DU4K is not draining all the water. There's at least a gallon of water standing in the bottom. I have cleaned the air gap assembly and drain line completely. They were even sanitized in hot water. I do not hear the water draining like it use to. When it worked properly you could always hear water draining into the GD. Now I can hear any draining. Again, there is no clogging anywhere in the drain line assembly. Is it a bad pump. I don't know where to go next with this.


... Magic Chef Dishwashers

My dish washer isn't cleaning the dishes well. There are little particals inside of every cup and on dishes after it is done. I just emptied and and now I'm running it with bleach. But before I started it I looked at the drain hose under the sink. The drain hose had water in it. The drain hose is going uphill from the dishwasher to the sink so I don't know if this is normal to have some water in the drain hose when the washer completes since it's not would have to pump uphill to get to the garba


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

My dishwasher SL34A015UC / 29 does not complete it's cycle. The cycle will stop with 1 minute left in the rince cycle and continue to run for hours, showing just one minute left. The dishes are not geting clean and there is a unplesent odor inside. I can hear the water draining during the cycle. The drain line is clear and there is plenty of water in the dishwasher. Any thoughts?


... Siemens SL5A70UC 24 in. Built-in Dishwasher

I have a Bosch dishwasher, stainless steel front- with buttons on the inside top( same as display, and the washing cycle won't start. Water seems to be running into the washer, as I can hear it, but the cycle never starts. Recently, I had clogged garbage disposer issue that has been resolved. The dish washer drains into the disposer, and I had free standing water left behind in the washer for 2days during this time.. Could this be the issue? Can you help me figure out this problem? Thanks!!


... Bosch 23 in. SHU 8805 Built-in Dishwasher

I have a 13 month old (Thanks Sears warranty!) Kenmore Portable Dishwasher Model 665.17769. It drains poorly, taking 2-3 times after load is completed running thru the ''cancel/drain'' cycle to clean it out. It is not getting dishes clean either, presumambly because the dirty water isn't being flushed out at cycle end and instead of rinsing with fresh water, it's still screwing with the dirty water. Manual doesn't offer any advice except to see if the hose is kinked (it isn't). I made sure nothi


Hello Linda it sounds like you may have a piece of glass or some other hard material in your drain pump which is partially blocking the draining process. Remove the hose in the base of the machine, then unscrew the drain pump and physically examine ... Kenmore Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I have a kitchen aid dishwasher that is stuck on the clean cycle. It will drain water, but no water seems to be getting into the washer. If i push the start button, cycle will not start. The clean light is the only light that will stay on. the other lights will go on, but they eventually go off without starting the cycle. Is this the thermal fuse???


... KitchenAid Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2391 seconds