Having problems with your Whirlpool DU1055XTS Built-in Dishwasher ?

My dishwasher runs 2 hours as a complete cycle. I think it is never going to finish but I have not stopped it in mid cycle. Dishes are very clean but they should when it runs this long. I hear it change cycles so I know it is not stuck on 1 cycle. It also makes a lot of noise. 2 hours of noise. HELP!!! How long it it suppose to run?


Answers :

That means that the machine does not detect that one condition to continue the cycle is met.

Sometimes\015\012 when this happen unesperience repairers replace the timer board , an \015\012expensive part that rarely fails. The timer board must be replaced only \015\012after everything else is tested, the problem is usually a sensor, or a \015\012faulty part that causes the condition to advance not being reached.

In your case, if dishes are clean , then filling heating and recirculating are OK, problem is likely the drain system not stopping, this is fixed replacing first the pressure switch, then checking pump and timer board.
If drain is OK, and machine hangs on drying (only self drying models), then replace dryness sensor or thermostat.
Check also that there is water pressure from the house line, and that the drain hose is not kinked or blocked.

The\015\012 door switch must be tested just in case the problem is caused by a \015\012defective door switch cutting off randomly with vibrations and causing the cycle to delay. This is \015\012tested jumping its contacts and running a controlled cycle.

All tests must be done with power off.

Try first tripping the circuit breaker and check the drain well, cleaning it and removin blockage. If that does not fix the problem call the support number listed on the user manual to have the appliance repaired.


Repair Help & Product Troubleshooting for Whirlpool DU1055XTS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishwasher runs 2 hours as a complete cycle. I think it is never going to finish but I have not stopped it in mid cycle. Dishes are very clean but they should when it runs this long. I hear it change cycles so I know it is not stuck on 1 cycle. It also makes a lot of noise. 2 hours of noise. HELP!!! How long it it suppose to run?


That means that the machine does not detect that one condition to continue the cycle is met.Sometimes\015\012 when this happen unesperience repairers replace the timer board , an \015\012expensive part that rarely fails. The timer b ... Whirlpool DU1055XTS Built-in Dishwasher

I have a Bosch (SHU5302UC/U12). The washer often takes 2 or more hours to run. Sometimes it gets stuck for a long time part way through (e.g. just sits at "43"). Other times, it gets stuck at 1 and won't stop on its own. The latest thing is 2 dots have appeared on the display that I've never seen before. For example, instead of "43", it reads "4.3." Eventually it gets to "C.L." but does not stop running. Also, its been making very strange noises during part of the wash cycle.


... Bosch 24 in. SHU43 Built-in Dishwasher

Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or


I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher

Sometimes I can run the dishwasher with no problems. Sometimes i will run it and leave the house and come back 5/6 hours later and it is still running on the wash cycle but it is only putting out heat and no water. So its drying up the soap on the dishes and not really washing anything, and it get stuck on that cycle


... Magic Chef 24 in. DU4500 Built-in Dishwasher

I have a Whirlpool ADP 5777 WH dishwasher I need to know if I can reset the dish washer, it is the timer which is stuck, so you can change the dial on the left for the various washes, eco, etc. but the time of the wash does not change!! Stuck at 2 hours 47 minutes!! I have tried turning the machine off at the powerpoint and turning it back on but that has not fixed it


... Whirlpool Dishwashers

After 3 years it just started making a loud noise, I am no expert but it sounds like a fan in a motor. I have only heard it today, but I am betting it will still happen next load too. I didn't change any of the settings, have been running the same way forever. When I did hear this noise I started pushing buttons to see if I could get it to stop, no good, no change. The cycle has completed and everything looks ok, waiting on the dishes to dry. Drainage has never been a problem for me either.


I would say this is a build up of lime.try changing your tablets and checking your salt levels.there is no fan .try what i say and see what happens.have you found a glass broken it could be as simple as that but i dont think its serious.adrian,,,, ... GE Nautilus 24" Built-in Dishwasher

Eurotech Model EDW254EWXX runs a 13 minutes cycle before washing like usual, but now it is getting stuck and not doing anything during that 13 minute cycle. No water is running, and it makes NO noise at all. We are not getting any errors displayed. I have unplugged it, and shut off the circuit breaker for 20 minutes, but the problem is still there.


... EuroTech 23 in. EDW254E Built-in Dishwasher

Hobart LXIH won't complete delime cycle. Enters delime mode and executes the delime cycle properly until about a minute or so into the rinse phase. Machine shuts off abruptly with E5 code mostly, sometimes E4 code. Changed the control board, didn't solve the problem. The LXIH runs the normal wash/rinse cycle every time without any problems. This is a nearly new machine that actually don't need delimed, planning on selling it and it must work perfectly. I know some would program the delime notifi


... Hobart 24 in. LXIH-3 Built-in Dishwasher

KitchenAid KUDP01DLBS2 dishwasher. Runs for a very long time on any cycle; time does not seem to advance. (takes 2.5 hours or more for normal cycle. "sensing soak", "water heating" lights on for a long time, even though it appears that water is not being heated. Checked incoming water temp, is hot. Did not do this when new, something has changed. Typical cycle was 1 hr 10 min. before.


Sounds like the heater inside the dishwasher is not working. The machine is trying to get the water up to a preset temperature, probably in the neighborhood of 140 degrees. That is one of the things that it is sensing.After the machine fi ... Dishwashers

I have a new Ariston LKF720 dishwasher. In part of its wash cycle it is very noisy - not water noise, but a grating motor-like noise. Is there anything I can do? Is there anywhere I can watch a dishwasher do a run and listen to its noise, Ariston or other brand? We bought the present one off the floor and did not expect any problem, having had other dishwashers for years, they being quiet. The poor technician already changed the motor, but it is still just as noisy. I am even considering sellin


... Ariston Technologies L63 Free-Standing Dishwasher

Long cycles My dishwasher (approx 7 years old) will run in the wash cycle for hours...until I physically turn the nob to "rinse"; then it will stay in that cycle until I advance the knob to the final (expel water) stage. I checked the filter and the blades - no obstructions. Also, when completed, the dishes are hot, so I know the heating element is working.


Http://www.thisoldappliance.com/library/bosch_dw_guide.pdf\012\012\012 ... Bosch 24 in. SHU43 Built-in Dishwasher

My Bosh dishwasher now runs well past the 105 minutes as stated in the manual, over three hours before I intervene. It gets stuck on the wash mode, it wont drain or rinse, just runs and runs in the wash mode (I know it's in the wash mode because when I open it up, theres suds inside). It will do the wash mode until I reset the wash mode to "Rinse & Hold". I appreciate whatever information you could provide.


Hello, welcome to Fixya.\015\012\015\012The problem you're describing is unfortunately a common one with B/S/H/ built dishwasher's. That includes Bosch, Thermador, Siemens, and Gaggenau. ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

Hi I have a bosch classix maxi been great for the last couple of years but it has failed for the first time yesterday. The dishwasher did not start it just kept making a groaning noise and would not start the wash cycle. I can press end a noise changes but the noise just keeps goin for hours if not manually stopped. Any suggestions?


Completely unplug the dishwasher and leave disconnected for at least 10 mins.\012\012Also be sure to check the drain pipe is not kinked or obstructed and that the filter is also clean and empty ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

My Bosch dishwasher SHU43C02UC/38 runs the quick wash cycle in an erratic way - seems to get stuck at the last stage of the countdown ("1") and, I think, goes back up and runs again. Instead of +/- 40 mins, takes an hour and a half.


Hi,The issue with your Bosch dishwasher likely lye`s within`the electronic timer/control, specifically the heater relay solder joint. ( a faulty flow switch, ntc or heater can also cause this, but not very probab ... Bosch 24 in. SHU43 Built-in Dishwasher

My Bosch dishwasher, model SHX46A05UC/30 has been working fine. I ran it once today on the Power Scrub Plus cycle (always use this one). Shortly after unloading the dishwasher I needed to run it again with more dishes. Within a few minutes of running the dishwasher I heard loud, almost grinding noises. Nothing appears to be stuck. Any ideas on what to do? This dishwasher has always been quiet up until today.


... Bosch 24 in. SHX36L05UC Stainless Steel Built-in Dishwasher

My dishwasher seems to run for 7 hours each time. What to I do? It seems to go through all the cycles and gets stuck at 1 minute for hours


There is well known problem for this model and I had it as well:On the control board the relay contact's soldering heated up and didn't provide contact, so the machine couldn't heat. Therefore the cycle became loooong!Right now I am experienc ... Bosch 24 in. SHU5305UC Built-in Dishwasher

We just installed a new kenmore dishwasher yesterday. Model 13242 It has been running for almost2 hours and is still on the washing cycle--no water in it however--is this normal? I'm in a bit of a panic as we are canning and I need the jars washed--we didn't get a manual with it as it was a floor model so I don't know how lon the normal cycle ids. HELP


THAT IS NOT NORMAL!!!!!!! A normal wash and dry cycle will take approx. 2 hours in length including drying cycle.\012You should see that water has been present in the machine within the first 2 minutes of the start of the wash cycle, you shou ... Kenmore Dishwashers

When we start the dishwasher running it just continues and continues and continues. For example earlier we set it for a normal cycle after almost an hour it still showed 44 minutes to run - and seemed stuck on that number


Replace timer ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My dishwasher is stuck on 40 minutes on the regular cycle. It won't go below 40 minutes. In fact, it's increasing the time on the cycle, jumping around from like 40 to 41, then 42 to 46, etc. It has been running for hours like this and I just noticed it.


... Bosch 24 in. SHU5305UC Built-in Dishwasher

Good morning, I have a F&P dishdrawer ds605i (i think!) single drawer intergrated front. I dont know whats happened to it. The last cycle it decided not to empty the water out, so i manually emptied it. Now it seems stuck. All it does is run the fan. i can't start a new cycle. The start/pause button allows me to open and close the door as normal and i can hear the lid opening and closing.......... I have tried turning it off for a day at the wall switch. I have also noticed i can


Hi \015\012I guess the model no. you have sent is not correct,however given bellow are links from where you can troubleshoot your problem to your dishwasher which is related to your issue:-\015\012 ... Dishwashers

My Bosch SHU 5315 always runs for 2 hours or longer for its washing cycles--read manual-- does not indicate how to change wash cycle to less time


"The repairman said these washers seldom have mechanical failures and the main board failure is the most common failure."Taken from this ... Bosch Dishwashers

I have an SDMO generating set with a Mitsubishi S3 L2SD engine it is supposed to run at 1500 rpm but goes up and down depending on load, if I set the rpm at no load to 1500 as soon as a load is applied the revs drop and so do the cycles from 50 to perhaps 48, if I set the revs on load, then off load the revs go up and the cycles hit 53 plus which means for example my washing machine does not want to know, I suspect the govenor on the pump but do not want to change the pump if this is within para


Set the no load revs such that you get 51 Hz out of the generator, at 80% load this ought to give you something like 48.5 Hz with less than a 3% drop in output voltage. If not, you might have governor problems but I'd try servicing and adjusting it b ... Karcher 2500 PSI Pressure Washer

I have an Inglis dishwasher.Serial number-FC3312512,Model number-IBU37002 or it could be IBU37062.I do not know how old the dishwasher is, as I justed moved in to my house this October,and the dishwasher came with the house.Last night I reset the options on the dishwasher,and had the cycle running on heavy duty.About 1 hour after the dishwasher was running this very bad smelling--like smoke- steaming odour was coming out of the door vent of the dishwasher.The smoke alarm went off in my house,and


... Dishwashers

I have GE GSD2300r00bb, it was working just fine the other day no unusual noise, today we tried to run it, just a little bit into the cycle, i heard a strange stalling noise that sound like the motor is stuck or something, i put a camera(in a ziplock bag) in the dishwasher to see if the blade is spinning, no spin, the water did squirt for about 1 sec then stop but still leaking out somewater. Is it the motor or the water pump. I just got this dishwasher about 1.5 yrs. Is this something i can fix


... GE GSD2300RBB Builtin Dishwasher

I have a new FDB520RHS2A Frigidaire dishwasher which remains in the wash cycle after I've started it. It sounds as if it is changing cycles but the wash light stays lit and never switches to rinse. The machine continues to run for hours if I don't stop it. We've checked the drain to the garbage disposal and it is clear. the water temp seems to be hot enough but how do I check that? Any ideas on what we should check before we bring it back to the store? Your help is much appreciated. Thanks!


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1124 seconds