Having problems with your Whirlpool DU1055XTSQ Built-in Dishwasher ?

My Whirlpool DU1055XTSQ has stopped working. The

\015 My Whirlpool DU1055XTSQ has stopped working. Pushing the start button does not do anything. The unit seems to have died completely. The breaker is not the problem and there does not seem to be a disconnect to the outlet. What else could it be?\015

Answers :

Check that the door switch is operating properly, open and close the door a few times, push in on the door with a good amount of force while trying to start the machine, the door switch will not let control power to the panel if it is not getting triggered, to let the processor know that the door is closed and it can start the cycle.
\015\012
\015\012 Good Luck !
Repair Help & Product Troubleshooting for Whirlpool DU1055XTSQ Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Whirlpool DU1055XTSQ has stopped working. The


Check that the door switch is operating properly, open and close the door a few times, push in on the door with a good amount of force while trying to start the machine, the door switch will not let control power to the panel if it is not getting tri ... Whirlpool DU1055XTSQ Built-in Dishwasher

Whirlpool Quiet Partner II: Was making loud noises while working. Then stopped working and cleaning light blinking only. Did the push buttons thingy - stopped blinking. Now just fills up, makes a humm


... Dishwashers

Whirlpool ADP4400 Yeah this is doing my head right in.when i plug in my dishwasher in and press the start button it goes something like this.(hmmm stop hmmm stop hmmm stop).anyone know what is rong with this.Pweese help.


So do i have to call someone out to fix this for me or is a quick fix poss.this is happening right at the start of the cycle,Thanks for your quick reply. ... Whirlpool 24 in. ADP5966 Free-standing Dishwasher

Whirlpool quiet partner II stops running or won't complete it's was cycle, sometimes is will wash for a few minutes and stop or it will stop before the water even starts to flow.


I had the same problem with my dishwasher. After hearing that the motherboard was the problem I decided to take a closer look. There were two capacitors (1000 microfarads, 6.3 volts) that looked a little suspect. The tops of capacitors should be f ... Whirlpool Gold Dishwasher with Quiet Partner Iv Sound Package

Whirlpool - Quit Partner I - DU1048XTP: Start at the beginning - Dishwasher would go through most of it's wash cycle and stop and the 'Start/Resume' LED would start flashing. Would press 'Start/Resume' and wash cycle would start again and run non-stop. Would have to hit 'Cancel/Drain' to stop. Called local service tech and he said board would need to be replaced. First board he brought failed right away, second board was installed. Tech also replaced latch handle assembly because it was missing


Have you asked the technician if the water temperature is OK.\015\012\015\012Run it again and after 30 minutes cancel and see if water temperature is warm or not. If not warm enough, then likely causes are heater is faulty or if you are u ... Whirlpool Dishwashers

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

Whirlpool Dishwasher continually cycles/won't stop


... Whirlpool 24 in. GU980SCG Built-in Dishwasher

Whirlpool dishwasher stops at rinse cycle and won't go


... Whirlpool 24 in. GU980SCG Built-in Dishwasher

Whirlpool Dishwasher stops during cycle, clean light flashing


... Dishwashers

My Whirlpool ADP6565 dishwasher stops before the rinse cycle. The start button then flashes and the rinse light on the cycle selelector knob is lit up. if I hold the start button in the water pumps out and then stops. I have to manualy set it to rinse to rinse the dishes.


You may have a blocked faulty, pressure sensor, or the hose is not flowing freely? Check that out.\015\012\015\012Below please find a service and repair manual, if you use the troubleshooting steps you maybe able to isolate your issue, and affe ... Dishwashers

Whirlpool dishwasher whirlpool ADG7440 dishwasher is starting then after about 5 mins it stops and the start button is flashing 2 times then pausing then flashing 2 times again


Hi,\015\012\015\012I can't guarantee to solve this but we had flashingh light problem and in the end all I did was to set the dial to the wash I wanted and kept my finger on the start button for about 10 to 20 seconds and it suddenly woke up an ... Whirlpool Dishwashers

Whirlpool ADP 4501 problem. Starts normally andthen after 30 secondes or so begins to 'pulse' ie pump runs briefly then stops and the power 'start' light flashes with each pulsation. No water coming into machine, seems to be trying to pump out but stopping


Sounds like electronic module failure if there is no water in machine. ... Whirlpool Dishwashers

I have a whirlpool dishwasher model number gu2400xtpq7. It stopped working. A fladhing light statred to blink. Light is "call for service" . Light blinks in series, 7 blinks and then stops. What does this code mean?


... Whirlpool GU2400XTPS Built-in Dishwasher

Whirlpool gold, quiet partner III, My dishwasher is not cleaning very well and when it is done it flashes clean. The clean flashing light wont stop. It flashes 7 times and stops for 3 sec then starts again. I know how to reset washer using heated dry and normal buttons but when i run it again when it is finished it goes back to the clean button flashing


... Whirlpool Dishwashers

My Whirlpool Dishwasher ADP931 has stopped working. It stopped in the middle of the cycle with 2 to 3 inches of water on the floor of the compartment. I mopped out the water and tried to restart the dishwasher. The green "on" light now comes on when I press the start button. but nothing happens (no motor comes on,no water enters).Repeating the above action several times does not help the washer to restart even though the other function lights will come on when the knob is turned. saturn1914


Hi,Whenever you see such symptoms, Time for you to investigate it properly. Check the below guide :-\015\012\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is\015\012there power getting to the dishwa ... Dishwashers

I have a whirlpool ADP-4685 WHM model. When i just switched it on there was a grinding noise at first then that stopped and it sounded ok and started to fill with water. It has now stopped again and the bottom left side light is flashing. Can you please help. I live in Spain, so my instructions book is in spanish! Thanks


... Whirlpool Dishwashers

I have a CDA CW494 dishwasher, which is a rebadged Whirlpool. The pump has been changed by a service engineer, using a Whirlpool part instead of the original, apparently it is superior. It seemed to work OK, but now the main jets only squirt for a short burst when the motor stops or starts. The rest of the time the motor can be heard running, but no water comes from the jets. Could the motor be running in reverse?


I would check to see if there is any blockage in the area of the dishwasher where the water collects to be recirculated through the pump back into the washer. It sounds as though the water isn't being allowed into the pump enough to continue the was ... Dishwashers

Whirlpool Gold Quiet Partner Model # GU980SCGQ2 The dishwasher normal light flashes on and off continually. The dishwasher won't stop cycling now, everything seems to work normally other than it won't stop cycling. I've attempted turning off the breaker- no luck. Attempted resetting the dishwasher- no luck. Any assistance would be appreciated. Is this a problem with the control module? The thermal fuse?


... Whirlpool 24 in. GU980SCG Built-in Dishwasher

Whirlpool dishwasher I have a 2.5 year old Whirlpool dishwasher and all of a sudden it stopped working. It is getting power because the Clean light just keeps blinking. Do you have any idea if it is something I can fix for cheap or is the unit junk?


I had the same problem with mine awhile back. I tried clearing it out like the book said and it would start blinking again when I started it. Then it wouldn't do anything. Based on research, I decided to replace the heating element and that solved th ... Whirlpool GU2400XTP Built-in Dishwasher

Have Whirlpool dishwasher Gold Series, Model GU9805CGB1 which stops part way through wash cycle with the led indicator blinks on the normal cycle.....if we ope nthe door and shut ...it continues until part way through rinse cycle...stops again....led indicator blinks again.....we open the door & shut and it continues....but then continues to run through the normal wash cycle continuously.....until we open the door again.....what's wrong???


Sounds like the door is losing contact with the door switch, first thing i would check is the door strike.Metal strike plate located on the tub itself that the door latch catches as it closes. its a spring metal striker, i would try bending it down ... Dishwashers

DISHWASHER STOPPING I HAVE A WHIRLPOOL ADG 7560/01 DISHWASHER. AFTER 4-5 MINUTES IT STOPS AND HAS A CONTINUOUS BEEPING AND THE START LIGHT FLASHES 4 TIMES THEN A PAUSE etc. I HAVE CLEANED THE FILTER LIFTED THE MESH AND CLEANED THE BOWL OF ANY DEBRIS AND WATER. I HAVE ISOLATED IT FROM THE ELECTRIC SOURCE LEFT IT FOR 10 MINUTES AND STARTED IT AGAIN TO FIND IT DOES THE SAME . LOST IS THE WORD THAT SPRING TO MIND. HELP!! MARTIN


... Dishwashers

My Dishwasher starts, then stops after 30secs and won't continue draining. Everytime I turn it back on it comes up on the steam cycle and won't go to any other cycle, drains for 30secs and stops again. Power light is flashing. Have tried holding power button down for 10secs with no effect. Filter is clean, pipes are straight-no kinks. How do I get it to start working again? It is a whirlpool dishwasher, ADP5550.


... Dishwashers

My whirlpool dishwasher starts the cycle but then just stops 2mins into cycle. If fills with water and then just when I think it is gearing up to heat the water it stops.. Can you help me?


Micro-controller is behaving erratic. You have to check with another set of PCBs ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have the Whirlpool DU 1100 dishwasher and the clean light kept blinking. I did the heated dry, normal combination and got it to run through the diagnostic check and sure enough it cleared the lights and appeared ready to run. When I would start it up again it would run the water and then get to the soad wash cycle and stop. No more lights it just stopped. I have been through the diagnostic process 3 times and still same problem. HELP


... Whirlpool Dishwashers

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to reset the


... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0920 seconds