Having problems with your Whirlpool DU1055XTSQ Built-in Dishwasher ?

Ive got a flashing clean light and the dishwasher won't run. Is there a reset button or a common part that causes this problem?


Answers :

Flashing clean light on a Whirlpool dishwasher is a heater \015\012malfunction (sorta) this failure code is generated when the unit does \015\012not sense a 5 degree rise in water temperature with in 15 seconds (give \015\012or take depending on model) some of the earlier models could show code \015\012under certain circumstances such as incoming water to cold.

With \015\012control off alternately press high temp scrub and heated dry till all \015\012the lights flash on and it will go into a diagnostic mode hit \015\012cancel/drain button twice and retry using the dishwasher if the code \015\012persists try running Your kitchen sink until water is hot then running \015\012the dishwasher if the code comes up again begin inspecting the heater in\015\012 bottom of wash tub for damage or signs of shorting also pull out from \015\012under the counter to inpect wiring to the heater, if these look good \015\012test the safety cutoff towards the front bottom of the unit small black \015\012and silver button sized componant with two wires to it for continuity.

Still\015\012 ok remove the thermistor from bottom of pump and clean it and test the \015\012ohms according to the tech sheet on the back of the toe panel on front \015\012of dishwasher, if this is ok test run the dishwasher with a high temp \015\012scrub option selected and test voltage to the heater at the two \015\012connectors directly at the heater if there is no voltage and You have \015\012properly checked the previous items the control has a bad heater relay \015\012and will require replacement.
Repair Help & Product Troubleshooting for Whirlpool DU1055XTSQ Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Ive got a flashing clean light and the dishwasher won't run. Is there a reset button or a common part that causes this problem?


Flashing clean light on a Whirlpool dishwasher is a heater \015\012malfunction (sorta) this failure code is generated when the unit does \015\012not sense a 5 degree rise in water temperature with in 15 seconds (give \015\012or take depending on mode ... Whirlpool DU1055XTSQ Built-in Dishwasher

The green clean light is flashing on my Kenmore Elite Ultra Wash dishwasher. After the reset sequence, the washer will run only 1 part of it's washing/drying cycle, then flash the clean light again... I have only owned it about 14 months, and this is the first problem I have had.


You may just need to reset your control board. Go to the link and it will explain how to reset the control board as well as explain what might cause the issue and how to fix it.http://www.appliancerepairlesson.com/dishwasher-2/dishwasher ... Kenmore 24 in. 17032 Built-in Dishwasher

Dishwasher We are having a problem with our Whirlpool ADP5540 dishwasher. We have just moved into a new house with this model dishwasher and have tried running it on a number of cycles. It always seems to stop part way through and the start button then flashes three times. Any ideas what the problem is or how to fix it?


If\015\012this is a blinking "clean light", this is a common problem with some\015\012of the Kenmore\015\012and Whirlpool models. I believe the problem is attributed to water supply\015\012temperatures being too low when filling. Apparently, th ... Dishwashers

Our GE Triton Dishwasher, mod# GSD5620D01BB is 10 years old. A problem started two days ago where; when it runs through a normal washing cycle; it contuously beeps about every 1 second when it reaches the Drying Cycle and the LED Green light flashes next to the Drying . I reset the breaker and tried again; same thing happened as it went through the normal cycle and when it reached the Drying part; same thing happened. The dishwasher is cleaning and everything else seems to be working fine.


The drying fan and vent system seems faulty.\015\012\015\012Refer this diagram. Item 918. ... Dishwashers

I have a Whirlpool Gold Model GU2700XTSBO its only 4 years old. About two weeks ago i noticed that the green lights were flashing and it would not run, I unpluged it for an hour and pluged it back in and the lights went away and it worked ok for the last two weeks. Last night I went to use it and there is no power at all to the washer, I checked the power source to the outlet and there is power there, so I dont know if there is a reset button or some control panel problem?


... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

Hi, I've got a dw 681es wh nemo dishwasher. I turn it on, it starts working but it sounds funny....and nothing happens. after a while the start/reset button flashes and then it doesnt continue. Any clues? I start it on the quick wash cycle but it quickly flicks to the rinse cycle when this problem occurs. I used to just reset and it worked again but now it just wont work.


... Fisher and Paykel Dishwashers

I have a kenmore dishwasher model number 665.17332400 the air dry button flashes on and off when u hit start button do run washer the quick rinse button flashes as well and washer will not run. What is the problem and how do I fix it?


... Dishwashers

My bosch dishwasher, one month old, has the active light flashing and the reset button won't reset it when I push it. A friend that was over opened the door when it was running because she can with hers, but ever since then, I had to take the water out and the active light is flashing and the wash light is lite. I hold the reset button for 5 seconds and then I shut it off for about 5 minutes, but when I turn it back on, the same things are happening


It sounds like the float is stuck. There is a float that stops the water from coming out when you open the door. It sounds like your friend stoped it in mid cycle and it jammed in the open position. Look on the inside of the machine for a plastic pie ... Bosch Dishwashers

Whirlpool gold, quiet partner III, My dishwasher is not cleaning very well and when it is done it flashes clean. The clean flashing light wont stop. It flashes 7 times and stops for 3 sec then starts again. I know how to reset washer using heated dry and normal buttons but when i run it again when it is finished it goes back to the clean button flashing


... Whirlpool Dishwashers

Hi there. I'm having problems with my dishwasher. Usuaully once loaded, i push the start button, the closest green light to the start button flashes and dishwasher fills/cycle begins. Now, when i push the start button, the furthest green light from the start button flashes, you can hear the motor running but no cycle begins. No water fills the dishwasher.


... Hotpoint 23 in. BFV62 Built-in Dishwasher

Clean light is blinking, have already killed the power, then called to whirlpool and they walked me through resetting it by pushing buttons, however when i attempted to run it after resetting it, it started to run then went right back to the flashing clean light. i tried resetting it again, and ended up with the same result.


You may a a latching issue. d/w not latching properly. How long does it take before the clean light comes on after you reset it. does it fill with water? if so, then your motor may be defective. ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Reset code I recently had a problem with my dishwasher that required me to use a reset code on my control panel. I can no longer find the manual that tells me that code. I was wondering if anyone knows it as to save a tech call. The error occurs when the clean light flashes. We have checked the heating element and the tech told us there is no problem there, we just need to reset the machine. The error has occured again, but this time because I tried to run the machine right when we came home fro


I believe the reset sequence is accomplished by pushing the NORMAL WASH then HEATED DRY buttons in that sequence two to three times. The unit will enter diagnostics mode, but can be stopped by pressing the CANCEL button. Let me know if this helps. ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

Have kitchenaid dishwasher kuds30fxss3. When pushing start button, start button starts flashing and beeping. If I reset breaker in basement, it will run one cycle and then start flashing the next time. Any solutions?


... Dishwashers

Am15 dishwasher problem: The pad will only turn on and off. Can't get it to cycle. Was on cycle 4 needed cycle 1. Got it to cycle 1, but now on and cycle does not work and when I push the off button it reboots to on. I put new pad on thinking it was the pad but same problem. Question: Is there a way to reset the board? should I be looking some where else? I cut the power at the breaker box to see if that might reset with no luck.


... Hobart AM15-2 Dishwasher

I can't get my electrolux dishwasher to run. It seems as though the touch pad is not responsive. It says to reset holding down the sanitize button, I do that it beeps but doesn't do anythng. All of the buttons are not lit up. I have to hold the delay start button along with the sanitize button to light the buttons up, still the buttons don't seem to be responsive, I touch the start and the lights go away and flashing numbers appear. Et 19 66 02 34 Any help would be appreciated.


... Electrolux EIDW6405HT Builtin Dishwasher

I'm having a problem with my Miele dishwasher G 879 SCVi I asked for assistance on 2/12/10 and paid $6.00. I have yet to get a response. Please let me know when I will as I need the problem addressed before Christmas Day. The problem again is that all the lights on the diswasher panel are all flashing at the same time when switched on. It may need to be reset somehow, as the power went off, which may have caused the problem. Your urgent assistance is required. Thank you


... Dishwashers

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

Have a whirlpool gold dishwasher.The problem is that the clean lite on the control panel flashes not allowing the unit to work.I installed a new disposal and forgot to remove the plug for the dishwasher drain hose.When the flood happened I opened the door in order to stop the dishwasher.Now the unit will not work.The lite flashes 7 time ,then it pauses and flashes 7 times etc.Is there a reset procedure to run in order to get the unit to work or do I need to buy a new control panel?


HI,Can you please give the make and the model no. so that i can give you the manual.Waiting for your reply ... Dishwashers

My kitchen aid dishwasher will not start I replaced the interface control board thinking that was the obvious problem. When you go to set the dishwasher to start some of the settings don't always light up then when you push the start button the lights will flash then start but it's not flashing and won't start. I get lucky once in a while and get it to flash then start. I don't know where else to look. I don't want to start replacing parts one at a time till I get lucky. My model # is KUDIO1F


Check all cables especially the ribbon cables from the user interface to the electronic control assembly as steam from dishwashings will create small amounts of corrosion and inhibit signals to and from these 2 components,unplug each,inspect,and reco ... KitchenAid Dishwashers

I need to know how to reset the "brain" the start button is flashing and won't stop when I close the door it makes a humming noise and no water is running. I turned off the breaker but it won't reset. Is there like a "hard reset" I can do


I don't think you may need to reset the dishwasher. All that might be happening is the float switch located in the base may be malfunctioning. It could be stuck. Try pushing it down and see if it lifts up by itself. It should only lift when water is ... GE Adora GHDA656LSS Stainless Steel Built-in Dishwasher

During circulation, top drawer seems to leak water through the rubber seal, located on the lid assembly. What would commonly cause this problem. Would it be the actuator, yoke, seal, etc... Please answer only if you've seen enough of this problem, with this model, in particular. Will provide monetary full rating if you can provide both, what part and why... and of course, if it resolves the problem :)


Lid seal not sitting properly can be due to several reasons as you have eluded to.\015\012\015\012The simplest is that the actuator is not getting any power. But if you hear the actuator operate at Start then this is not a problem. Howeve ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

I have a GU1500XTLB1, type-575-0 Whirlpool Gold dishwasher. For the last couple of weeks I've been getting the control lock on. I got the manual out, I hold the air dry button and it clears. My problem is now when I turn the machine on dosen't matter which cycle I hit (pots and pans, normal, or quick wash) it runs for about 5 minutes and it goes into a mode with the timer having lines going horizontal with the air dry button lit up and rinse button lit up. It sounds like it starts the cycle


Hi,There are Few Tricks to Reset this. Follow the below Tricks :-1. Try holding down heated dry key for 5 secs. I believe that is the control lock/unlock button on your model. IF not, look for the lock symbol and follow same i ... Whirlpool Dishwashers

During circulation, top drawer seems to leak water through the rubber seal, located on the lid assembly. What would commonly cause this problem. Would it be the actuator, yoke, seal, etc... Please answer only if you've seen enough of this problem, with this model, in particular. Will provide monetary full rating if you can provide both, what part and why... and of course, if it resolves the problem :)


... Fisher and Paykel DD605I Dishwasher

I have 2005 model KUDSO1FL and clean light flashes 7 times and won't start . Solutions for reset don't match my buttons. what is the reset? I also have latch problems--machine pops open over


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1644 seconds