Having problems with your Whirlpool DU1055XTSQ Built-in Dishwasher ?

Small padlock is lit-up on controll panel dishwasher will not wash or cancel


Answers :

Press and hold HEATED DRY selector for 5 seconds
Repair Help & Product Troubleshooting for Whirlpool DU1055XTSQ Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Small padlock is lit-up on controll panel dishwasher will not wash or cancel


Press and hold HEATED DRY selector for 5 seconds ... Whirlpool DU1055XTSQ Built-in Dishwasher

I have a KitchenAid dishwasher model#KUDC25CH.The problem that I am having is the touchpad control panel all of a sudden is lit up like a Christmas tree. Just about every red indicater light is lit. The DW will run but I dont know what kind of wash it is performing or at what stage the cylce is in. I have tried canceling the cycle,I have tried child lock/unlock,I have cut the power to the unit for a few minutes hoping the computer panel would reset itself. I am affraid to run the unit in fear th


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Kenmore Ultra Wash Dishwasher Model 665.15779 LOCK ON light blinking on control panel, unable to use washer. If buttons were locked, LOCK ON light should be lit continually not flashing. If you press and hold NO HEAT DRY button to disengage lock, nothing happens. If you press the CANCEL button it begins to blink in unison with the LOCK ON light. How can I stop the light from blinking to allow button function again?


... Kenmore Dishwashers

Maytag model MDB5600AWB replaced faulty control panel started and lit up like it is supposed to do started wash with glisten cleaner and when I tried to cancel drying cycle panel or board would not respond, waited till unit was finished and control panel blinked and went dark , bad control board?


... Maytag 24 in. MDB5651A Built-in Dishwasher

Dishwasher model 665.13763K602 SER FU3009053 the control panel on the front of it has 4 lights on and won't turn off. they are the pots/pans, norm wash, china, and fast wash. the other 2 lights will not turn on - smart wash and quick rinse. I cannot make the dishwasher start. When I press the cancel button, it does something for about 60 sec. then stops.


... Maytag Dishwashers

We have a Kenmore Ultra Wash Dishwasher Model number 665-13859K601. The Normal wash and the Cancel (drain) buttons are flashing red on the control panel. No matter what we have tried, we have been unable to correct this problem. Obviously the dishwasher does not function. When you close the door the lights keep flashing and no button combinations seem to do anything. I have looked at the troubleshooting guide that came with the dishwasher, however there is no


... Dishwashers

I have a maytag mdb6650 aww dishwasher. The dishwasher just stopped. The light on the control panel is on. If I push the buttons to try a different cycle, the light over light wash remains lit, so the buttons don't seem to respond. I was wondering if it is the control assembly, or if the door switch is not working. The handle cracked a while ago, but if the dishwasher still worked even though the handle had cracked in half.


... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

My Kenmore dishwasher model #66515639000 quit working. It was washing dishes just fine one day and then the next the buttons weren't working properly. The pots & pans button was flashing with the cancel button. After searching on your site, I tried to resent the control panel by pressing the normal wash button and the air dry button 3 times then opening and closing the dishwasher. Now the quick rinse button is flashing. Any ideas of what to do now?


... Dishwashers

Kenmore dishwasher ultra was quiet guard 3 model 56516012403 control panel will not activate red lights blinking on normal wash and cancel drain. did the hold the heat dry button then the normal wash button, it stopped the blinking but the dishwasher will not engage when you push any button


That would be model # 66516012403 correct??you may have inadvertently set the lock on function.. check this out from your manual...Lock OnUse the Lock On to prevent unintended use of the dishwasherbetween cycles. Y ... Kenmore 15912 Built-in Dishwasher

I have a Kitchenaid Dishwasher Model #KUDI01FLBL6. The heavy wash light is blinking on it. If I hit cancel, all the lights start blinking on the panel. I have replaced the control panel part #8564542 on it and it's still doing the same thing. The tech sheet is missing on it so I'm not sure if I should reset or how to do a diagnostic on it. Can you help with telling me what to do?


HI. The control board was actually not the issue here. The interface will be the lone culprit in this case. There is a stuck circuit or button that is causing this warning(blinking lights). The button is mounted on the interface and you will need to, ... KitchenAid 24 in. KUDI01FL - Multiple Color Built-in Dishwasher

My dishwasher wont run when i push the start / cancel button the washing light comes on and blinks ,but the dishwasher does not turn on . i put in a new control panel and it still does the same thing.


Check the water level switch/ pressure switch.Control panel may not have full control. There may be yet another board inside! ... Frigidaire Dishwashers

Kenmore Elite Ultra Wash Dishwasher 665.1397 Nothing Working on Control Panel


... Kenmore Dishwashers

My dishwasher will fill and start washing, but then cancels itself (I think during the rinse cycle). I have tried a new control panel (both inner and outer) and a new circulation motor.


... KitchenAid Dishwashers

My whirlpool dishwasher is ocasionally filling back up with water, whether the door is open or closed, and regardless of of control panel being lit. It happens, then leaks out the front. If i run the cancel drain, it will pump out the water just fine. All the other cycles are working just fine, and it leaves no water at the end of of the cleaning cycle. I have found no common occurance for this


Greetings,\012\012 in most instances the water inlet valve is leaking..this is the water valve that brings water into the dishwasher...its possible, the drain water is running back into the d/w from the drain hose not installed prope ... Dishwashers

FDB834RFS0 FRIGIDEAIRE DISHWASHING M# FDB834RFS0 Precision Wash System.... All control panel blinking.... Main power turn of and repower then ONLY HI TEMP WASH and NO HEAT DRY LIGHT ON. How do I enter control panel mode to clear blinking lights? Could it be faulty element inside dishwasher? Any suggestions gladly appreciated. Tks .. AA


... Frigidaire Dishwashers

Kitchenaid dishwasher model KUDS24SEWH2 fills with water, lights on control panel work but doesnt wash or cancel


... KitchenAid Dishwashers

No power Our 3-yr-old dishwasher (Whirlpool 24-inch ) stopped in mid-cycle. A small amount standing water in the bottom of the washer. None of the control panel buttons were lit up and none of them will work. NO POWER


Hi lushman001\015\012\015\012I'm Harvey the Master Plunber.\015\012\015\012Your question is: your 3-yr-old dishwasher (Whirlpool 24-inch ) stopped in mid-cycle. A small amount standing water in the bottom of the washer. None o ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Kenmore Elite 665.7696 dishwasher - "normal wash", "pots pans" and "cancel drain" lights flash on control panel. If power shut off for some time will work for part of load then start flashing again and stop. Is this a trouble code? If so, what does it mean?


Hi\015\012\015\012This error code appears when either the keypad(Part#1 in below link) or Control board(part#11 in below link) is faulty. You can reset the error codes sometimes by turning Off/On the power, however, this is not a permanen ... Kenmore Dishwashers

Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than


... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher

Our dishwasher was taking in water, circulating it but not heating it up or moving through the cycle. My husband took the control panel off and there were some scorch marks on it so we got a new one. He replaced the control panel and the dishwasher went fine for one night. It heated up and washed everything perfectly. The next day when we put it on it was back to square one plus the lights on the control panel are now not working. Just wondered if anyone has any idea what we could do or are


Yes it's time to visit the dump ... Siemens 24 in. SE64A630GB Built-In Dishwasher

Frigidaire FDB1502RGC0 dishwasher set for normal wash and heat dry option, both leds are on. dishwasher cycles through wash, but never makes it to dry cycle. After wash, the leds for OPTIONS high temp wash and dry cycle start blinking and do not stop blinking until I hit cancel - which cancels everything. Open unit and water sitting in bottom. Is it a bad operator panel? Water pump did seem to be working during wash cycle. NEED HELP.


... Frigidaire 24 in. FDBB540 Built-in Dishwasher

I bought an IKEA Renlig DW60 dishwasher about 6 months - the controls are located on the inside top of the door. Ordinarily the dishwasher turns on and three red LEDs on the far right of the control panel light up. On occasion however only a single red LED indicating the temperature of the last wash I carried out will go on (it is always the 50 degree light as this is always the wash temperature I use). When this happens the dishwasher appears to be stuck and will not start when I shut th


Press and hold the cancel button for about 5 seconds. This resets the electronics and gets it going again ... Dishwashers

I have a mdd8000aws dishwasher. After a power outage (2 days) the power came back on, and the bottom drawer no longer works. It still make the chiming noise when the drawer is opened, but the control panel is not fully lit up and the washer will not start in any mode. The lights seem to flicker for a short moment and then they all stay very lightly lit up. Is this just a bad control panel or is there some other circuit that needs replaced? BTW, the top drawer works perfectly.


... Maytag MDD8000AWS Builtin Dishwasher

Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che


... Dishwashers

I have a whirlpool quiet partner i dishwasher (model DU1055XTSQ2) that has suddenly stopped working. Control panel has partial functionality. All of the buttons on the control panel have a green LED feedback light when depressed. None of them provide LED feedback anymore except the Hi-Temp Wash, Sani-Rinse, and Heated Dry buttons. So there is power to the dishwasher. Any ideas? Please help Scott


The control board has failed.CLICK HERE to see the parts breakdown. ... Whirlpool DU1055XTSQ Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2306 seconds