Having problems with your Whirlpool DU805DWG Dishwasher ?

My spray arm stopped rotating?what can it be?


Answers :

Repair Help & Product Troubleshooting for Whirlpool DU805DWG Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher Repair Dishwasher is a Stoves/Newhome DW616 Rotating spray arms do not always operate. This is an intermittent problem - will sometimes work normally for a few days then arms will not move at all with no water coming from them. Machine appears to go through its normal cycle. Some times cycle starts normaly and spray arms stop working part way through.


It could be a motor or a pump issue. The dishwasher has a motor that attached to a pump which forces the water up into the sprayer arms and during the drain cycle, it pushes the water out of the dishwasher. \015\012The motor (and pump) located beneat ... Dishwashers

Belling IDW604 - How do I raise the upper basket......in this dishwasher so that the upper spray arm can rotate without bashing my standard size dinner plates below? I'm told you can fit bigger wheels but won't that stop the upper spray arm from connecting with the water supply?


... Belling 24 in. IDW602 Built-in Dishwasher

Motor hummed loudly and lower spray arm didn't spin. Replaced motor which stopped humming and gave a lot more pressure but lower spray arm still won't spin. any thoughts?


Check for clogged vents. Try checking by hand for freeness .Hope no vessel is obstructing it's movement. ... Dishwashers

Bosch SKT 20 table top dishwasher water stopped heating up, spray arm has stopped rotating and spraying


Bosch SKT 20\015\012επιτραπ?\302\255ζιο νερ?\302\214 πλυντ?\302\256ριο πι?\302\254των σταμ?\302\ ... Bosch Dishwashers

Two problems: the water pressure in the arms is low. If you pop the door, arms are not spinning as it should. Each time you start and stop, the arms move a tiny bit. Have cleaned the filters and the spray arms completely. Also, detergent door no longer pops open.


Hello, Welcome to fixya.\015\012 \015\012I just came ... Bosch SHU3306UC Built-in Dishwasher

Junk inside spray arms stopping them up.


Every once in a while, run it with powdered lemonade inside. It'll cut down on your lime deposits. It works. Just dump it inside. No need to put it in the resevoir ... Dishwashers

Hi, I have an LG LDS4821 dishwasher and it appears to stop working properly. The dishes don't seem to be cleaned at all. It seems like the spray arms are not spraying the dishes as the dishes are still dry/dirty after a normal wash cycle. I did notice that the detergent was used during the wash, and a trail of white residue was at the bottom of the tub. I can hear water pumping into the dishwasher, but when I opened it during a wash cycle, there was a puddle of water at the bottom of the


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... LG LDS4821 24 in. Built-in Dishwasher

I have an inglis ipu5846 built in dishwasher it fills thaen trys to start but wont start or drain now i took off the lower spray armthe part that is screw down under it tryed cancel drain and it worked put thetop bacck on but not the spray arm and it wont work.what stopping that from working there are not any moving parts on that piece


... Whirlpool Dishwashers

Our KitchenAid whisper quiet model number kudp02crcs2 seems to have stopped filling?? or at least it does not spray any water and the arms do not turn...there is a very minimal amount of water in the very bottom and arms when we turn it on....it has also started to make a different low level sound..


... KitchenAid 24 in. KUDP02CR Built-in Dishwasher

The cycle doesn't seem to stop correctly. I start a load. It doesn't seem to matter which mode that I start in, but it will count-down the time, but at the end it hasn't stopped running. I've cleaned out the filter and the trap below. I've ran vinegar through a cycle. I've cleaned all of the spray arms. It doesn't seem to advance out of the wash mode. There is still some suds at the end. I have to end the cycle by canceling and draining it manually, then run a couple of "rinse--9 minute" cycles


Hello,\015\012\015\012Based on your description I'd say the issue is with the control. That is what I'd be looking for if called out to service the unit with the symptoms you've described. \015\012\015\012The issue is within t ... Bosch 24 in. SHU43 Built-in Dishwasher

Asko 1385 dishwasher spray arm doesn't stop when door is opened


If there's a fault it's with your door latch/switch cheers ... Asko 1385 Dishwasher

My cda dishwasher cw448 is 18 months old, and has recently begun to stop before the end of the cycle. When I open the machine, 3 lights flash, (one of them the rinse button), and the machine bleeps repeatedly. Why doesn't the cycle complete? I've checked the filters, the spray arms, all the dispensers, and manual doesn't give any answer. This doesn't happen all the time, but is occuring more often now.


... Dishwashers

F2 Code Hey, I have a single drawer built in Fisher & Paykel dish drawer and today I pulled the spray arm, filter and large metal screen out to clean them as we have been starting to get a bit of stuff left behind after washing lately. That was all good After putting it all back in though I went to use the dishwasher and it stopped and came up with an F2 fault, I thought I may not have put the bits back in properly so pulled them out again and noticed that on the rotor that connects the motor to


Fault F2 means the rotor is not rotating. If you say some of the vanes have broken off, they could have been jamming it. This should spin freely with minimal force when installed correctly. If you removed the rotor itself, you do ned to take care whe ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a GE dishwasher (GSD4020Y70BB) new in 1996. I replaced the whole motor assembly in 2007, seal was leaking. My dishes are not getting clean now, dried food left on plates, coffee stains in cups not being cleaned. I removed main spray arm, found nothing, turned washer on and plenty of water gushing out. I took the cover off sump all clean. I removed the filter screen in the back, there appears to be a valve with some soft rubber around it. Water gushes out of this, does stop during the cyc


Have you checked the drain pump impeller and drain hose? I am curious if there is a back siphon from the drain hose or the waste outlet at the garbage disposal might be blocked or plugged with food debris.\015\012I wou ... Dishwashers

Water stopped pumping so ordered new pump. Upon removing the old I discovered it had a few straws twisted up into the pump. Removed and reinstalled pump and it sounds great and throws water all over with force. PROBLEM: Now there is ZERO water coming through top tube to spray arm. Pulled pump back off and noticed what seems to be a "white diverter ball" that moves a little in front of the inlet for the upper water tube. Any guidance to where the ball should be prior to installing the pump


... Kenmore 15529 Built-in Dishwasher

Hello I have a Bosch dishwasher SHU9905UC and went to clean the spray arms etc and ran the machine without the filter screens in the bottom. **** went everywhere, food, soap scum etc and it first stopped draining and filling. Cleared the drain flap and now works on drainng and filling. But now the wash pump is not running. I figure **** is somewhere in the wash pump or blocking a micro switch etc. I can turn the impellor with my finger. Is there a micro switch in the pressure chamber that is a


... Dishwashers

Water stopped pumping so ordered new pump. Upon removing the old I discovered it had a few straws twisted up into the pump. Removed and reinstalled pump and it sounds great and throws water all over with force. PROBLEM: Now there is ZERO water coming through top tube to spray arm. Pulled pump back off and noticed what seems to be a "white diverter ball" that moves a little in front of the inlet for the upper water tube. Any guidance to where the ball should be prior to installing the pump or i


... Kenmore 15529 Built-in Dishwasher

Dishwasher fix water does not go through the spray,. the upper hand an lower hand are clean , the pump does operate to empty the dishwasher . I do smell like some burning smell when I turn the dishwaher on, the water start running for 1 minute or 2 than stop shortly and doesn t reach the arm then the dishwasher becomes hot inside . Thank you


Something has gotten passed the screen and is jamming your pump impeller pull lower spray arm pull screen and see if you can find what is jamming the impeller and remove it drain pump is separate ... Maytag MDB7100AWB Dishwasher

SGS45E02GB: Water is entering the DW as normal, all accessible filters are clean, pump is going, but something is stopping the water reaching the spray arms (yes, they are clean as well). Where is the blockage (if that is the problem) likely to be and how do I get at it?


You may be hearing the wash pump running but that does not mean it is sending the water through. \015\012\015\012I am assuming the water is collecting in the base of the dishwasher. \015\012\015\012You will have to confirm if ... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

My miele a660, suddenly stopped sparying water.Machine takes water and drains it but does not spray at all. arms are clean


I believe that is your motor that is shot. When the motor spins it creates a pressured vortex, which sucks the water down into the unit and shoots it out through the tubes.\012So no water movement means your motor which is about $130 is probably dea ... Miele 24 in. G638 Plus Free-standing Dishwasher

My spray arm stopped rotating?what can it be?


... Whirlpool DU805DWG Dishwasher

The machine does not seem to rinse properly. We have checked the water fill level, water temperature, spray arms are not clogged, have determined it is not a hard water problem and have tried Glass Magic and CLR to verify the lattter. What else can we check to stop getting a film on everything in the machine? Plastics come out terrible, glasses and dishes foggy and sometimes still greasy. The model # is GU2700XTSY0 from the Whirlpool line of Quiet Partner 4. Any suggestions would help. Thanks!


Too much detergent; not rinsing well; hard water... There is an acid wash to revamp glasses/ you'd need to google it... ... Whirlpool GU2700XTSS / GU2700XTSY Built-in Dishwasher

Maytag dishwasher with a spray arm that is stopped up and I need to remove it and clean it.


We have a dwu7400 so i'm not sure it is the same, but above the top arm you should see a serrated ring (looks a bit like a flower petal) and that should spin off and the arm should come with it. There's a snap that holds those pieces together that if ... Maytag 24 in. DWU7402 Built-in Dishwasher

My fisher paykel DD603 fills with water at the start of the cycle and stops with the following error code and a beeping noise: - error U1 spanner symbol - crossed out faucet symbol. The water level is high enough that the spray arm is floating in the water. I am able to drain the water by entering the hardware diagnostics mode and running the motor in the drain direction. By removing the filter plate and examining the impellers I am not able to see visible damage. All filters are clean. The


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. You are spot on as error U1\015\012indicates that the dishwasher has twice tried to fill with the required amou ... Dishwashers

This is a past problem posted that I am now experiencing with my Kenmore Elite Model 655.17489300 dishwasher. Looking for any suggested solutions, Rick Past Problem: I have the same problem with my 2004 Ultra Wash Model 665...fills with water, sensing light comes, then stops for a second. Then you can hear another pump kick in (it hums) and just runs continuously but no water is spraying through the arms. When you cancel the wash, it drains perfectly. I've checked the filters, all is c


The symptoms you have mentioned could be linked to the soil sensor which some models come with. The purpose is to run the drain pump and let more water flow through inlet valve if during wash cycle the dishwasher detects soil collection in the accumu ... Kenmore 24 in. 16539 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0785 seconds