Having problems with your Whirlpool DU806CWDB Dishwasher ?

Whirlpool Dishwasher Stuck in Cycle

\015 My Whirlpool\302\240DU8750XB1\302\240dishwasher gets stuck in a cycle when it runs. It looks like it happens at the same point in the cycle before it reaches ''rince'' and during that time, the ''delay-water heating'' light is on.\302\240\015\012\015\012Could this be the thermostat? I believe it has 2 of them. A regular and a hi-limit stat. Are they easily replaced? I looked at the\302\240underneath\302\240of the unit but can't see them. Are they housed somewhere else?\302\240\015\012\015\012Or am I way off?\302\240\015\012\015\012Any help is appreciated.\015

Answers :

Repair Help & Product Troubleshooting for Whirlpool DU806CWDB Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

Dishwasher Whirlpool ADG7540. Does not complete cycle. Approx 20 minutes into cycle dishwasher appears to get stuck on rinse.The water is cold. Machine stops and makes a constant beeping noise and the green light flashes 3 times repeatedly.


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

Whirlpool dishwasher stuck on prewash cycle - Whirlpool Dishwashers


... Whirlpool Dishwashers

Whirlpool Dishwasher Stuck in Cycle


... Whirlpool DU806CWDB Dishwasher

Whirlpool dishwasher stuck on prewash cycle


The eprom memory is brocken,the main board must be changed. ... Whirlpool 24 in. ADG7952 Built-in Dishwasher

Whirlpool dishwasher won't go into wash cycle as it usually did. just humms, then cuts off, staying stuck in that cycle...


So i assume it fills with water then just sits there? this would be a wash motor problem, It could be a blockage in the wash motor or an electrical issue.Some of the whirlpool models have a start capacitor on the motor which can fail and woul ... Whirlpool Dishwashers

I have a Whirlpool DU1048 that started out with a blinking clean light. I reset the dishwasher by pressing the heated dry and normal buttons twice. That worked the clean light stopped blinking. The problem now is the dishwasher seem to be stuck in the wash cycle. I finally have to turn it off after over an hour washing. Is this possibly a heating element problem? is that user replaceable?


... Dishwashers

I have a whirlpool for Ikea dishwasher that is built in and I put it on the normal 30 minute cycle before I went to bed and 8 hours later it was still going. I opened the door and machine was full of suds. It is like it gets stuck and can't move on to the next part of the cycle. I have checked the filter in the bottom of the machine and checked the salt and rinse aid levels.


It could be waiting for the temperature to reach the required level.\012\012Sounds like the heater element has died. ... Whirlpool Dishwashers

My Whirlpool ADG957/3M dishwasher refuses to continue cycle,start button is flashing continuosly with beeping noise,also unable to select different cycle,stuck on rinse after selecting 65 degree wash.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or\015\012door lock switch which is not engaging its ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a SHU3032UC BOSH Dishwasher for a couple of years now. Always worked as expected. Latetly, the dishwasher never stops. It looks stuck on an "unknown cycle"... The cycle dial stays at the "bottom" cycle (there's nothing written). If I turn it 1-2 "clicks", the dishwasher continues its work and ultimatly finishes with very good cleaning results. Once, I open the dishwasher when it was stuck in the "bottom" position, and there was hot watter at the bottom. Here's what I've tried so


Hello, welcome to FixYa.\015\012\015\012Based on you description of the timer not advancing I suspect the thermostat isn't satisfied when heating the water.\015\012\015\012The SHU 30** unit`s with a mechanical timer have very few if any, issues with ... Dishwashers

Whirlpool gold dishwasher stuck at 78 minutes in normal cycle


... Whirlpool Gold 24 in BuiltIn Dishwasher w Adaptive Wash Cycle Dishwasher

How do i reset my whirlpool adg 7460 dishwasher ? programme seems stuck on end cycle?


Unplug it, move timer to start and plug back in. If it still seems stuck at the end it is almost certainly the timer. If it starts as normal, suspect the drain pump or pressure switch ... Dishwashers

We have had delivered a new Whirlpool ADP451 Dishwasher. The test cycle was ok , and now we wanted to wash our first time and found that the machine will not work, it is stuck on Express program , this keeps flashing with a loud bleep bleep.. Is the machine faulty?


... Whirlpool Dishwashers

Whirlpool dishwasher gu2700xtsqI does not cycle timer stuck on 1 minute


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Whirlpool GU2400XTP Built-in Dishwasher

I have a whirlpool DU1145 dishwasher that seems to be stuck on the same cycle. It shows it as sensing and washing at the same time and never shuts off. HELP! WHat could becausing this??


Sounds like your Touch Pad on the Control Panel is defective. You can try and remove the 120 Volt AC power from the Dishwasher by turning it off at your Main Electrical Power Panel with the Circuit Breaker (15 or 20 amp) lab ... Whirlpool Dishwashers

I have an ignis dishwasher by whirlpool and it seems stuck on the rinse cycle - it wont move on and the machine is beeping non stop. I have switched the machine off several times and unplugged it but it still lights up on the rinse icon and is still beeping and I cannot move it on


... Dishwashers

It is stuck between cycles. How do i reset? - Whirlpool 24 in. GU1200XT Built-in Dishwasher


Have you tried turning the mains power off and on after a short delay?\012If this does not work then press the following buttons in quick succession (about 5 sec) and when all lights light up press Cancel.\012\012HIGH TEMP SCRUB, ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

I have a whirlpool 940 series dishwasher yhat seems to be stuck on the Pots/Pans wash cycle. Is there a way to clear or does someone understand what the problem might be or a resolution?


Hi Sam, I am Kelly. \015\012\015\012If pressing Cancel Drain 2 times after a power up from power being disconnected does not reset the controls you have a problem in the control boad itself. Usually what happens on an older unit is corr ... Dishwashers

BF41 Dishwasher with a leak stuck in mid cycle Hi, I have a 'general domestic Appliance Ltd' BF41 (95+G709394) dishwasher which recently started leaking at the door. After replacing the seal the problem seemed to ease, then recently the problem started all over again and the leaking got worse. A couple of day ago I couldn't stop it leaking and now it's stuck in mid cycle and even though the water is washing inside the machine it never gets hot inside or finishes the cycle. Ive tried stopping and


... Dishwashers

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

Problem for Kenmore 24 in. 15992 Built-in Dishwasher Previously answered by Ginko but have not had any responses since June 18 and problem not solved. No water flow into dishwasher. Actual model is Kenmore Elite undercounter dishwasher 665.15982990. Float is not stuck. Worked fine for 10 years until mid May. Display shows cycle is on and counting, for all the different cycles. No valve or motor sound when starting cycles, only a single electronic click. When cycle is canceled, motor does s


Hi.Sorry about your old query.If there is no power on black wire and no filling, then check and eventually replace the thermal fuse. The thermal fuse is attached to control board. If it is faulty it will read continuity, norma ... Kenmore 24 in. 15992 Built-in Dishwasher

Dishwasher is making a loud grinding noise when it's started. Doesn't matter the cycle choice; the cycle starts as normal then once started up starts making a sort of grinding noise as the water is pulsing, like something is stuck or blocking the "push" of water. I couldn't see anything stuck in the bottom - any thoughts before I call a repair person? I've never owned a dishwasher before - maybe there's a basic drain/blockage thing I should check out first? And, any recommendations for repair


... Maytag 24 in. MDBH970AW Built-in Dishwasher

Kenmore Dishwasher My dishwasher fills with water and then stops. I hear the cycle timer continue all the way through the cycle. I pulled the screen off the bottom inside of the dishwaher and stuck my hand in the diswasher drain. Originally I felt and cleared what appeared to be a torn up rubber band. I feel a thin straight metal pin that I can rotate and I believe it causes the pump to rotate as well. Once I do that the dishwasher will run normally thorough a complete cycle...BUT I have to


If you have either dry bearings in the motor or sticky grease buildup in the pump bearing/seal, it can cause the motor to stick rather than rotate on startup. More likely to be greasy crud buildup. \015\012\015\012The best you can do without disasse ... Kenmore 24 in. 15149 Built-in Dishwasher

I have a Kenmore dishwasher model # 66513449K900 that will not stop running. I think it is stuck on the drain cycle. I can start the dishwasher on a cycle and it appears to clean the dishes, but after the cycle is complete, it continues running and running (on the drain cycle) until you open the door. What could this be?


It is possible that the machine does not move off the cycle because there are errors or back feedback from the inputs. For the program to end the main program controller must receive the feedback so as to switch off the circuit at the end o ... Dishwashers

I have a Jade RJDW2470A dishwasher which was re-branded Jade. (It is a Maytag product.) It get's stuck between cycles and will run forever unless I manually advance the dial to the next cycle. It seems to get stuck around the "rinse" cycle and the soap door does not open until after I advance it past that cycle.


... Jade RJDW2470A Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1885 seconds