Having problems with your Whirlpool DU930PWS Built-in Dishwasher ?

How do I remove the filter on the bottom of the dw so it can get cleaned out?


Answers :

Repair Help & Product Troubleshooting for Whirlpool DU930PWS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi! My bosch SHE43 built in dishwasher is about 2.5 yrs old, dishes aren't getting clean anymore. We have *really* hard water so I use the max rinse agent, but doesn't help. I clean the little canister filter with each wash, and just washed off that grate in the bottom. I also just cleaned the trap under the sink, but it didn't look bad at all. The problem is a grit left on glasses and things just not getting all the way clean. When I remove the grate at the bottom, there's a bit of water


Hello. Let's begin by tossing two cups of vinegar into the empty dishwasher and running it on it's hottest and longest cycle. Always run the hot water in the sink faucet until it is as hot as it gets before starting up the machine. Let that cycle ... Bosch SHE43C02UC Dishwasher

Hi there I have a Miele G663 scvi dishwasher. The inlet/outlet light is flashing. I have cleaned the non return valve and filter at the bottom of the machine. I have also removed the water inlet pipe which has a large filter on at the end where it attaches to the water pipe. I have blown through this pipe and it is quite difficult to get air through. Do you think it is a filter that is blocked? If this is the case are they easy to attach to the bottom or the machine or would I have to get


... Miele 24 in. Incognito G663 SCVi Built-in Dishwasher

Hi, I have a Fisher Paykel DD603I (integrated) dishdrawer unit. The bottom drawer soap dispenser has water in it after it runs (and leftover soap), and there is a small amount of water sitting in the bottom of the drawer. The dishes don't get totally clean. I have removed and cleaned the spray arm, drain filter, filter plate and bottom of tub. Found nothing clogged or particularly dirty. Put all the parts back in and everything moves freely. Ran it empty, and same problem occurred.


Hi Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doe ... Fisher and Paykel Dishwashers

My Professional series dishwasher does not work properly. It is only 1.5 years old and glasses on top rack get sprayed with fine layer of particles every time I use it. Other items, top and bottom, are often not clean as well, but glasses are the hardest to re-clean. I have tried evacuating the water left at the bottom of the dishwasher before running, pre-running the hot water in the sink and ensuring that the disposal was run, removing and cleaning the filter at the bottom of the washer. None


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Frigidaire PLD4375RFC Dishwasher

I have a MODEL 577-0 kudk01ILb55 KITCHENAIDE dishwasher. I am trying to remove the inner pplastic bar that goes vertically through the system from top top bottomj so that I can clean out the filter. But I do not see how to remove that bar. I have looked online for a repair manual of some type but have been unsuccessful. Can someone tell me how to remkove the bar so I can get to the filter on the bottom? I have already removed the star shaped rinse sprayer.


... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Dishes and glasses not getting clean. Visaul inspection; it lloks fine. Removed filter and bottom perforated filter panle and cleaned off mineral-like residue. ran test program: result flashing lights for Clean & rinse/dry buttons. not sure of next step...help please.


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Bosch 23 in. SHU3307UC Built-in Dishwasher

GU2400 whirlpool gold quiet partner iii. Won't clean dishes. Dishes don't get wet. Water seems to accumulate at the bottom but no spraying sound during cycle. Cancel causes the system to drain completely. Possibly plastic utensil under the filter screen at bottom. Can't figure out how to remove it or the filter screen. Might be preventing impeller blades from rotating.


... Whirlpool GU2400XTP Built-in Dishwasher

There is food left on the dishes; the air tube is clear, think it must be the drain is blocked with food;; so removed bottom basket took off the middle plastic 'nut' and removed the 4 metal screws ,but really stuck on the next step. WE have been trying to get that darn screen-filter off to get to the place to clean out PLEASE help! THanks


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Dishwashers

My Kenmore 13743 is 3 years old and was washing perfectly until a couple of months ago. It has become so bad that it won't clean anything on the top rack and barely anything on the bottom rack. In fact, I just pulled a butter knife out of the rack that still had butter on it! Not normal... I do not know how to remove the bottom washer arm to get at the chopper, filter, etc. Please help


Hello,\015\012\015\012Welcome to FixYa,\015\012\015\012You are likely right on, this is very common with these unfortunately. Hopefully this will help.\015\012\015\012**Unplug the unit or turn off the powe ... Kenmore 13743 Staimless Steel Built-in Dishwasher

Machine just started leaving dirty water in bottom of machine. cleaned filters,had machine apart,removed and cleaned waste pipe. pump runs and impeller feels ok.only time i could get any water to drain into bucket was when shook waste pipe very hard?


Check that the pump is clean and not loose. Make sure pump, impeller, and waste pipe are in alignment with each other and are clean. If it works when you shake the pipe, then there is still a clog inside or the pipes aren't aligned correctly and some ... Dishwashers

My Kenmore Elite model # 630.16302402 dishwasher isn't getting the dishes clean. A lot of food is still on the dishes after cleaning, especially inside the glasses. There is a white film on glasses and the inside of the appliance. I also just noticed that the upper arm isn't turning. There is about 1/2 cup of water standing in the drain area (not visible until removing the filter tray at the bottom of the appliance). Is this normal? The obvious problem is the upper arm but it seems like the rin


Hello, \015\012 \015\012 ... Dishwashers

Does not get my dishes clean, leaving a film on my glasses, not getting food off. tried to take apart to clean but could not figure out how to get bottom filter out with the large water bracket going up the back of the dishwasher to the top water bar. I bought as a store model, no instruction booklet. How do I clean out bottom filter?


The problem is hard water. www.dishwasherfilter.com has a product to solve this problem once and for all. It filters the water going into your dishwasher and removes the ... Jenn-Air 24 in. JDB1100AW Built-in Dishwasher

How do I remove the filter on the bottom of the dw so it can get cleaned out?


... Whirlpool DU930PWS Built-in Dishwasher

Dishlex global 310 - I've cleaned all filter components and removable parts but still it's like no high pressure water is getting through. How do I check to unblock the inflow at the bottom of the unit?


When the Dishlex starts for the first time, there is a\015\012service mode set up. The service mode allows you to set a 'fill-time'\015\012for the water to reach the right level, depending on the water pressure\015\012and flow... So resetting the ... Electrolux Dishwashers

I have a Kitchen Aid KUDS03CTSS3 dishwasher. Dirty water is staying at the bottom and nothing comes out the drain hose during the entire cycle. The drain hose is looped above the kitchen P-trap, although for a time it wasn't. I use a wet vac to get the water out but there is still water below the fine filter. I thought if I could get the fine filter off, I could clean out the bottom as I think that it's full of crud down there that may be blocking things. I can't figure out how to get the l


Hi,Thanks for the follow up. I am glad it worked out for you. If I can Help in the future let me know. http://www.fixya.com/support/c64627-kitchen_aid ... KitchenAid 24 in. KUDP02FR Built-in Dishwasher

I have a whirpool Quiet Partner III, and the top layer of glasses is not getting clean. I had a technichian out some time ago, and the problrem was caused by food debris trppaed in the filter in the wash module. He saud it was easy to clean that out, so I have removed the lower spray arm, but cannot undo the 4th screw that will allow me to take the grey round filter cover off to remove the food or paper debris. It is under the white flat pipe that delivers water to the wash module, and I cannot


I had same problem, would not clean well and fixed it. . I cracked open the door during wash cycle and used screwdriver to defeat the door lockout. The water from the bottom sprayer was only shooting half way to the top of dishwasher. To fix I remove ... Whirlpool Dishwashers

A glass shattered in a thousand pieces in the dishwasher. I cleaned and vacuumed everything except the very bottom that I can't get to. I took out 8 screws, removing the round rotator piece at the bottom, but that still doesn't get me into the very bottom where I'm certain there is still glass. Question #1 - Will leaving the glass down there hurt anything? Question #2 - If yes, how do I get the rest of the part off without damaging it? I have a 10+ yr old Model DU920QWDB3 Thank y


The glass should just go down the drain from there. I doubt any piece that made it into there should damage anything as they are would have to be pretty small and as big as any food particle that could fit into there so you should be fine. If you rea ... Whirlpool Dishwashers

My dishwasher spray arms were clogged with calcium buildup so I cleaned one and replaced the other. I also removed the fixed disc-shaped device underneath the lower spray arm and found the particle filter was clogged- so I cleaned it out. The dishwasher ran fine for a few times but then the filter clogged again, and again, and again. Now I need to make a routine of disassembling the parts to get at the filter every week because the filter no longer clears itself during the wash and/or emptying c


You may want to check your hot water tank. It may need drained and cleaned, Or you may have the rod in the tank disintegrating. Also check you water faucet areators to see if they have calcium pieces too. ... Maytag Dishwashers

My two year old Bosch dishwasher is not cleaning well and is leaving gritty food on most glasses, cutlery, etc. Worse on the top but also not good on the bottom. I have tried cleaning the removable filter on the bottom and rinsing the two 'wands' - one on top and on the bottom so that the little holes are not blocked. I've tried using the power scrub mode. I've run the dishwasher twice with detergent and no dishes. This has problem has persisted over at least a month. Can you please help me?


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch Dishwashers

I have a triton xl model @ gsd6200g00bb serial #va790400b. The dishes on the top rack are not getting clean. I have removed the top, and middle, and bottom arms cleaned calcium out of them. Removed the screen below the lower arm cleaned. The top and middle arms are still not spinning during wash cycles. Where do I go next?


Apart from the spray arms themselves there could be other reasons why the water is not getting up to the middle and top arms.\015\012\015\012The distribution circuit from the wash pump that feeds the arms could be blocked or the wash pump ... Dishwashers

Asko 1996 appears "dead".....no lights flashing, won't respond to repeatedly pushing on/off button. Some water left in the bottom...siphoned it out, cleaned filters, no blockage there. Almost like it's not getting electricity, but breaker is on. Noticed this when I went to empty clean dishes, and noticed that detergent hadn't dissolved and dishes weren't clean and about a gallon of water was still in the bottom.....


Don't know if this will help, but my dishwasher has a "propeller" device above the top and bottom racks that spins while dispensing the water. If the dishes on either rack are stacked too high (i.e. if even one plate comes in contact with that ... Asko D1996SS Built-in Dishwasher

Upper spray arm is not turning and I don't think water is coming out. Dishes on top are not coming clean. Dishes on bottom are clean (as clean as they get with this dishwasher). How do I remove upper spray arm. Also I'm not sure how to remove lower dish rack to access upper spray arm. Any help appreicated. Kitchenaid model KUDP01FLSS5 Chris


Hi Chris,It sounds to me like a restriction in the pump. I put together some information here on cleaning it out. If you try these please give me some feedback as to if they help or not.Thanks! ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

JENN-AIR Model number JD3B10AWX. Bottom of dishwasher is dirty, I want to clean it. I have removed six screws holding plate down, but cannot find any way to remove spinning blade. I think there's a filter underneath that I can clean or replace. Questions: 1. How to remove spinning blade? 2. Am I going about this correctly. Thank you


We have been having issues with our model where there is dirty sand deposited inside of glasses and dishes.You need a torque wrench for a triple square torque screw ... Jenn-Air Dishwashers

I have a KitchenAid KUDS03CTSS3 and the longer I own it the worse it gets. At 1st it was a great, but as time goes on it doesn't barely clean a thing... It's frustrating me to have to rewash everything by hand. It has a filter system that isn't removable for cleaning... what do I do now? I'm sure if I could clean the filter it would be fine. Someone please HELP!! :) Chantal


... KitchenAid 24 in. KUDP02FR Built-in Dishwasher

I have a GE dishwasher (GSD4020Y70BB) new in 1996. I replaced the whole motor assembly in 2007, seal was leaking. My dishes are not getting clean now, dried food left on plates, coffee stains in cups not being cleaned. I removed main spray arm, found nothing, turned washer on and plenty of water gushing out. I took the cover off sump all clean. I removed the filter screen in the back, there appears to be a valve with some soft rubber around it. Water gushes out of this, does stop during the cyc


Have you checked the drain pump impeller and drain hose? I am curious if there is a back siphon from the drain hose or the waste outlet at the garbage disposal might be blocked or plugged with food debris.\015\012I wou ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1238 seconds