Having problems with your Whirlpool DU930PWSS Stainless Steel Built-in Dishwasher ?

My dishwasher is less than 10 months old. I was running it last night and it just quit before the drying cycle. Now nothing on it will work. I checked the breaker, nothing was tripped.


Answers :

Hi
\015\012\015\012


\015\012Thanks for using FixYa. To start with try to leave the unit unplugged for\015\01210-15 minutes and while its unplugged check for clogs in the drain hose.
Usually, these issues are related\015\012to kinked hoses, knocked out disposer unit (if connected with the dishwasher\015\012drain hose) & clogged drain pump & filter. Some of the most common\015\012reasons include that the drain hose isn't working properly, the drain pump\015\012isn't working correctly, or possibly there is a plumbing problem in your home's\015\012drain lines. First check whether the drain is not clogged or blocked and the\015\012line is not kinked. Check all the hoses for blockages, if everything appears to\015\012be fine then it is better to use warranty and get it replaced/repaired. Please\015\012accept the solution if the issue is resolved or post a comment for further\015\012assistance.
\015\012
\015\012Thanks

\015\012\015\012

Rylee

Repair Help & Product Troubleshooting for Whirlpool DU930PWSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishwasher is less than 10 months old. I was running it last night and it just quit before the drying cycle. Now nothing on it will work. I checked the breaker, nothing was tripped.


Hi\015\012\015\012\015\012Thanks for using FixYa. To start with try to leave the unit unplugged for\015\01210-15 minutes and while its unplugged check for clogs in the drain hose. Usually, these issue ... Whirlpool DU930PWSS Stainless Steel Built-in Dishwasher

Kenmore 665.13599k600 was working fine and just quit in the middle of a cycle nothing lights up i checked the breaker its fine..


... Kenmore 13599 / 13594 / 13592 Built-in Dishwasher

My son opened the washer before it completed the full washing cycle. Now it won't start at all. We checked the switches, gfi, circuit breakers. Is there a reset button somewhere? I pushed and held the Heated Dry Button for 4 seconds. Nothing works.


HI- You didn't give a model # but it is possible that the fuse on the control board burnt out. This shuts the unit down if it gets blown. Yours may not have this fuse, can't tell without a model number but if you are sure it is getting power I'd h ... Kenmore Dishwashers

Hello, Our kitchenaid DW has stopped working. Non of the buttons cause a any of the lights to turn on. Of course, it will not start. On its last working cycle, it had a very strange washing cycle. It almost sounds like the water was not splashing around (even though I opened it while it was working and noticed water at the bottom). I checked the circuit breaker, and it is not tripped. For a couple of weeks, the DW had started making a kind of metallic noise while in the washing cycle. Also,


It is nice to see a problem described with such a depth of observations. It helps in closing on to the possible causes of the problem.\015\012\015\012For the moment let us make sure there are no remnants of the glass left in the dishwashe ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Avanti dishwasher stopped working. I have checked breakers-the dishwasher lights do come on-it will not cycle. When it first stopped working, the motor was working, but the dial would not move. I tried to cycle it to drain the water, but then nothing more happened.


... Avanti 18 in. DW19PSS Platinium Built-in Dishwasher

Maytag MDB6600AWW Unit is approx 3 years old it was finishing a load and stopped part way through sticking on heated dry. I don't know if it was there in the cycle or if the diagnostics on the board sent the message there. The light now will not shut off or move from the heated dry. I have disconnected 120 volts, removed the panel to check wiring, removed board and reassembled nothing resets the heated dry light and nothing works. I have gone through manual function test, sales floor demo test,


Have you tried pushing heated wash, heated dry, heated wash then heated dry? Sometimes this will reset it. ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

I have a GE Quiet Power 3 dishwasher that was working fine last week. Over the weekend I ran it and we could hear a banging noise, so my boyfriend opened it three or four times in a row (during the cycle) to figure out what it was. The fourth time, it went dead. I checked and it had tripped the breaker. I reset the breaker and the dishwasher seemed to be working again, however the lights on the front were flashing (they hadn't previously), and now it will run for about 10 minutes but no water ru


Were you able to figure this out? We have the same problem here! ... Maytag Dishwasher

The dishwasher stop during the wash cycle. It did finish draining the water from the tub. The machine is not showing a power signs, I check the circuit breaker and the fuse is not tripped. I open and closed the door and the door latch seems to be working fine. There is just no power to the washer. Usually when a machine breaks down, there still is power or buttons that light up on the front of the machine. I looked on the internet and many say that the fuse could be tripped. No where can I find


... Whirlpool DU912 Dishwasher

Frigidaire FPHD2491 electronic buttons not working. Only China/Crystal cycle will light up and can be selected. All others do nothing. I checked the control lock and it does nothing. seems like the electronics are messed up or something. I turned power off and back on through the breaker and it made no difference.


Hello bamspry - From what you are describing if only the China/Crystal icon is working, then the dishwasher could possibly be experiencing a communication problem coming from the main control panel or wiring failure. If I was in your position, I p ... Frigidaire FPHD2491K Builtin Dishwasher

My Kenmore Dishwasher won't turn on. Was working fine last week, but when I went to start it yesterday, nothing starts or lights up when I push the button. The options buttons still light up, but thats it, the wash cycles and the start and stop buttons...nothing happens. I tried tripping the breaker to reset and it did no good.


Hi,\015\012\015\012A device may cease to function or operate sporadically if the electrical cord is damaged. Inspect the cord for any damage. Check whether there are any black smudges or burn marks on the outlet, cord or anywhere the cord comes ... Kenmore 15129 Built-in Dishwasher

Kenmore elite dishwasher stopped in middle of cycle with water still inside. Checked breaker. Replace the hole control panel, door latch from a used kenmore elite. Work for half a cycle and quit with water still inside just like the first time.


Here's your solution (free PDF) - Kenmore Elite Dishwasher Manual ... Kenmore 24 in. 16352 / 16354 / 16359 Built-in Dishwasher

Wash cycle stopped with water in the bottom. Seems like there is no power. Can't get lights on cycles buttons to turn on. Power button does nothing. Checked circuit breakers. All are on. Lights and outlets around dishwasher area are working.


Check the wiring in the units junction box. Its located at the bottom right corner. You will likely find melted connectors. If so, you need to cut the wires back and replace these connectors. Make sure you turn the power off before doing any of this ... Bosch 24 in. SHX46A05UC Built-In Dishwasher

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

I have a Whirlpool Gold Quiet Partner III (Model GU1200XTKB0). I have used it previously on "Normal" cycle and I always keep it on Air Dry. Last night I used the "Pots and Pans" cycle and it seemed to work fine. But this morning the Air Dry light is flashing and if I press a cycle key the Rinse Only light starts to flash as well. Nothing works. I have made sure that the console is not locked. Any suggestions? I do not have a Heated Dry button, only Air Dry. Thank you.


... Dishwashers

My whirlpool dishwasher model DU800CWDB5 stopped in middle of rinse cycle does not work at all acts as if no power checked fuse box no breakers tripped


... Whirlpool Dishwashers

I have a kenmore elite dishwasher model # 665.13103k902. It was working just fine & then one day I ran the cyle and it lost all power in the middle of the cycle leaving water standing in the bottom. My husband checked the breaker and also unplugged it and plugged it back in and still nothing...any suggestions?


... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

My dishwasher just stopped working in the middle of the wash cycle. It seems to have no power to it. I have checked all the circuit breakers and reset them all and still nothing. Any ideas?


Your hard wiring maybe bad, or a wire nut came off call electritian or someone who knows electricity ... Whirlpool 24 in. GU980SCG Built-in Dishwasher

Our dishwasher was working fine (about 3 yrs old). Woke up in the morning and went to unolad it. There was a small amount of water in the bottom and it does not respond. No power, lights, nothing. I checked the breaker and it had not tripped. Any suggestions?


First turn off the breaker. Once you have the power off, take off the bottom panel.You will see where the electric wire comes into the dishwasher, it should have a small cover over the connections.Take off the cover and you will most likely find that ... LG Dishwashers

Control panel will not light up, the dishwasher was running and now it has stopped mid cycle and will not do anything. I just replaced the control panel (black plastic with buttons, not control circuitry). was running the diswasher and it seemed to be working fine, then stopped. water is standing in tub, I checked the float, I don't think the float is the problem. There is power to the outlet, no tripped breakers. But control panel will not light up.


I have a kitchenaid dishwasher model # KUDC10FXBL1 I went to start it and none of the buttons were working. I have checked the breaker and the wiring and everything seems to be in order. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

Same problem! Stopped mid cycle, no power, no lights, nothing. Checked fuse box breakers fine. Bought it a year and a half ago! piece of SH#$! Its a Kenmore now its a $350 drying rack. please help!


Sounds like the main control board needs to e replaced this is the most likely problem ... Kenmore 15129 Built-in Dishwasher

Our Dishwasher is not draining. We tried to run a test cycle and noticed there is no power. We checked the Electrical Panel and noticed that an unmarked breaker was tripped. We turned it on but still have no power. All other electrical items are working in the house. Is the power being cut off as a fail-safe function due to the water not draining? How do I fix the drain/pump? Please Help!


Hi,No, the water is a result of the dishwasher going off mid-cycle...Take the front kickplate off and see if you have power at the makeup box...you will need an electrical meter to check that...if there is power there then you have ... Dishwashers

My dishwasher stopped working during the wash cycle now i have no lights on the front panel. i checked the breaker but nothing wrong


... Kenmore 15762 Dishwasher

My dishwasher's buttons will not work at all. Nothing is lighting up. I have already checked the breaker (not tripped, but I turned it off and then on again just to rule that out)... I assume that it is some control panel (the manufacturer said that it is a covered part... but I will have to pay the tech to come and install). Just trying to determine if it would be something that I can do myself and save some $. the unit is only 3.5 years old...


... KitchenAid Architect? II U SERIES KUDS03ST Stainless Steel Built-in Dishwasher

Dishwasher I have had above integrated dishwasher which is intermittently tripping the mains fuse. Power is getting to dishwasher and the washing cycles work until a certain point (not the same time) where a loud bang can be heard and the main fuse is tripped. Reset the main fuse and power still gets to the dishwasher and it works again. It has just started to trip the fuse when its not running any cycle (just when power is getting to it). I've checked the fuse on the spur and it looks ok. I hav


Its quite common for the interferance filter to fail on these models its situated in the base of the dishwasher connected to the mains block usually when they fail you can see black dust around it, ... Neff 24 in. S5456 Built-in Dishwasher

Whirlpool gold quiet partner iii quit during a cycle. none of the lights on the control panel work. there is power going to the unit from the breaker box.


... Whirlpool Gold GU2275XTVy Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1268 seconds