Having problems with your Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher ?

Two horizontal dashed line and won't start

\015 I have a Whirlpool Dishwasher GU2400XTPB7. When you press for a specific cycle type, the only thing that comes up is two horizontal dashed lines on the time remaining. The dishwasher won't start. If you press the cancel button it will drain for 2 minutes and shut off. Is the problem a console issue or a board issue?\015

Answers :

A dishwasher operates in a hostile environment. Eventually the corrosive soap can damage the electrics & the electronics. If you have the skills, I suggest you turn off the breakler to the diswasher, then dissassemble the console & control board. Spray the contacts with WD40, & reassemble. The very sliding-action of dissassembly/reassembly should cure any contact issues. I hope that this helps.
Repair Help & Product Troubleshooting for Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Two horizontal dashed line and won't start


A dishwasher operates in a hostile environment. Eventually the corrosive soap can damage the electrics & the electronics. If you have the skills, I suggest you turn off the breakler to the diswasher, then dissassemble the console & control bo ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Kenmore dishwasher 16934 will not start up for me. I can push any button to set the cycle(pots & pans, china gentle, quick rinse, normal wash) and the time shows up in the display, but when I push the start, two red horizontal lines appear in the time remaining display. Cannot get the machine to start anything. All cycle buttons give me some kind of time remaining display but as I said, it ends up with 2 red lines. Thanks in advance. Mark


... Kenmore 24 in. 16934 Built-in Dishwasher

Carburator is gummed up I can remove the carburator but after that im lost I removed the screw from the bottom of the cup drained the old gas shot some carb cleaner in there opened the gas line put the screw back in numerous times wont start regapped the spark plug and cleaned it won't start only has been used about five hours my buddy didn,t run the old gas out of it two years ago before winter it's a type 5 manual choke/fixed throttle


... Karcher 2500 PSI Pressure Washer

For my Kudi01dl model dishwasher, the rinse light is on, but the unit will not respond to any buttons being pressed and won't turn on. When I press any buttons, two horizontal lines show in the front, but go off as soon as I let go of the button. Is there a ways to reset the unit? Everything was functioning fine the last time I used it. I use it about once a day. The problem started when I heard sounds coming from the unit, very loud motor sounds. The door was closed but I had not turned


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

I have a Kitchenaid KUDIO1DL white dishwasher which is a few years old now but has worked great since I bought it. Today it has the lean light flashing and will not turn on. there is power, and the drain button seems to work, but I can not get the cycles to come on. When I press the start button, I just get two dash lines and then the unit turns off. Thanks


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

GU1500XTLQ Does not start, anti bact and rinse flash, if I press CANCEL the Time Remaining gives me two horizontal bars


... Whirlpool 24 in. GU1500XT - Multiple Color Built-in Dishwasher

Whirlpool dishwasher gu3600 The pots & pan, normal light and delay lights flash all the time. Also the time remaining screen has two horizontal lights on. The dishwasher won't start


... Whirlpool Dishwashers

Red light at the ''s'' symbol wont go off and the dishwasher wont start its programme the model is IDF125 aa class and is less than two years old but the instruction maual is missing!


... Maytag Dishwasher

Hi My dishwasher stopped mid rinse cycle, with a little water still in it. Lots of beeping later i managed to set it back to start but it wont go, just beeps. The line to sink seems to be clear. There is no gurgle sound when i try to start it. model number SB907WJ*00


Hi,Is there my error code there?If you set the appliance to drain do you hear the pump running?Bail the water out manually and then take the filters out.Bail out the water below the filters.Take off the ... Dishwashers

I have a GE dishwasher model number GLD55OOLOOWW. It was starting a start cycle and i opened the door to put more dishes in and my finger must have hit a button on the door and now two lights flash off and on and it wont reset itself. It has been on for several hours and still blinking and beeping every so often and unplugging it does not help. Any suggestions how to solve this problem. Thank you.


Try pressing the cancel button ... Dishwashers

My Troy Built 2500 psi power washer with Honda engine GCV has been stored for 2 years. I changed the gas and could not get it to start. Which is the start position for the valve on the gas line - Horizontal or Vertical? Thanks, Bill Gray Melbourne Beach FL


... Pressure Washers

Frigidaire Dishwasher This is my second dishwasher in 18 months. Water leaks out the bottom of the dishwasher. It did it on my first one now it''s doing the same thing.Could it be the water pressure from the city water line? How could this happen to two dishwashers in a row? The leak starts immediately when the wash cycle starts.


This is a simple solution, the brass nut that connects the heating element to the base of the dishwasher is cracked and needs replaced. It takes just a few minutes to replace, just remove the nut after TURNING OFF THE POWER and take to your local par ... Dishwashers

Further to my open question for my Asko N516 D5131 SS dishwasher I have been able to successfully press the wash setting cycle, which was before frozen on 'rinse and hold' . I then press the on/off. Button the time shows but as soon as I press it to start the dishwasher the screen changes to three horizontal curly lines and nothing further happens... It won't start. Please , I do hope somebody can give me advise. I cannot get to the power plug as it appears pot be located behind the unit whi


... Dishwashers

Whirlpool dishwasher gold won't start 2 dash lines on time remaining button


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Dishwasher i have a ge dishwasher i purchased two years ago. i have misplaced my owners manual. i can only tell you it is a ge quietpower 3. i don't even know the model since i've misplaced my owners manual. it started with the timer for speed cycle set itself between 50 and 60 minutes, and i knew that wasn't right. and then yesterday it did not drain all the water out. i know there is no food particles in it because i clean them before i put them in the washer and the drain line it is hooked up


Hi lilwing,\015\012\015\012I'm Harvey the Master Plumber.\015\012\015\012Your question is: you have a ge dishwasher you purchased two years ago. you have misplaced your owners manual. you can only tell you it is a ge quietpow ... GE 24 in. Profile PDW7800 Built-in Dishwasher

My 5.5 honda engine on my lawnmower will start but wont stay running already cleaned the carb out didnt help there is no restrictions in the fuel lines im lost please help


It sounds like a fuel problem.\015\012first drian fuel out of tank.\015\012i know you have already cleaned the carby but dis assemble carby and clean with carby cleaner.\015\012re assemble carby & fill tank with fresh fuel.\01 ... Honda Pressure Washers

I have a GU1500XTLB1, type-575-0 Whirlpool Gold dishwasher. For the last couple of weeks I've been getting the control lock on. I got the manual out, I hold the air dry button and it clears. My problem is now when I turn the machine on dosen't matter which cycle I hit (pots and pans, normal, or quick wash) it runs for about 5 minutes and it goes into a mode with the timer having lines going horizontal with the air dry button lit up and rinse button lit up. It sounds like it starts the cycle


Hi,There are Few Tricks to Reset this. Follow the below Tricks :-1. Try holding down heated dry key for 5 secs. I believe that is the control lock/unlock button on your model. IF not, look for the lock symbol and follow same i ... Whirlpool Dishwashers

Engine will not start,almost sounds like it is backfireing out of the carburater ,I cleaned out the old gass and put new in, cleaned gas lines,blew out carb with air two times, it ran for about 10 seconds the first time, and nothing the second time,----------What !


Pour a large amount of carb cleaner into the gas tank\015\012With choke on full, pull cord often to work carb cleaner into carb and then let it sit for a day or four.\015\012Your carb is dirty for sure.\015\012The venturi and jets a ... Honda Pressure Washer PSI 3000

Red light above quick rinse flashes. Unresponsive to anything other then when I press drain cancel two horizontal lines turn on and off


May I get the make and model # to help you more ... Dishwashers

Kenmore elite 2 front loading washer model#110.45872400 It first flashed the code FH and then went to the running time is now flashing and it sounds like it is running but the cycle never starts and I cannot cancel the cycle by pressing pause/start two times. I have checked the water lines and the screens and cleaned out the drain catch below. what next


... Kenmore Dishwashers

Model EXVRB2321 would run only with full choke, now wont start after cleaned carb,tank,what is the plug gap,I got a champion EZ start5843spark plug, replaced fuel line pvc boot, getting juice to plug and compression is 60 to 62 lbs psi.


... Briggs Pressure Washers

Dish washer shut off between cycles, have power going to unit but wont start is there a in line fuse, or something , or could it be in the switch


Check for front panel setting called sani-heat or other which causes the machine to wait until water in the lower tub is heated to about 145F. This is to save energy for situations where hot water supply is not close by or not sufficiently hot. The ... Dishwashers

My dishwasher will not drain. When I try to run it through the drain cycle by hitting drain/cancel button it makes one click and nothing happens. I checked for blockages in the drain line and valve but the motor just wont start.


Check to determine if the pump out motor is functional by checking if supply voltage is across the 2 terminals in pump out mode with a AC voltage meter. If voltage is present and motor does not spin this is an indication that the motor is open circui ... Dishwashers

I have a Kenmore Ultra Wash 665.17772990 and bought it second hand washed a load maybe two but worked great and now it wont start is there a sequence code I can put into it I have seen some suggestions of one but I lost power and lost it. If you have any advice it would be great. Thanks for your time. Paul


Either the door lock is not making contact or the thermofuse on the control board is bad. ... Dishwashers

It wont start and is flashing to the symbol of an arrow pointing to a line


This is a typical Anti Flood system activation. This system activates when water leaks onto the floor of the machiene due to a leak fault (pipe/hose clamp/ partly blocked pipe). The machiene automatically switches to pump out mode and stops water inl ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1209 seconds