Having problems with your Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher ?

My Whirlpool Gold Model #GU980SCG52 is leaking on the outside of the Water inlet. The hose is attached on top, but the water is leaking out of the opening on the front side under the hose.


Answers :

HI. this is a inlet assembly issue. The water inlet valve can be identified by the water hoses connected to it. One hose will lead from the valve to the pump/motor assembly in the center of the dishwasher. Check that the hoses are securely connected to the valve and that there are no kinks in the hoses which could restrict water flow. There are two wires (four, if it has two solenoids) connected to the water inlet valve. Label the wires and connections so that you can properly reconnect them later. The wires are connected with slip on connectors. Firmly pull the connectors off of the terminals (do not pull on the wire itself). You may need to use a pair of needle-nose pliers to remove the connectors. Inspect the connectors and the terminals for corrosion. If either is corroded they should be cleaned or replaced.

Use a continuity tester or multimeter to test for continuity. Set the multimeter to the ohms setting X1. Touch one probe to each terminal. A reading of infinity indicates a bad solenoid that must be replaced. Different brands and models will have various measurements, but the valve should show some resistance if it is functioning properly. If your valve has two solenoids, test the second one in the same way as the first.

If the solenoid is working properly, but water leaks through the valve even when the dishwasher is off, then the valve itself is the problem. Debris may be preventing the valve from closing. If the valve cannot be cleaned, it will have to be replaced. The valve can also fail mechanically. So even if it passes the electrical test, it may still require replacement. If you have ruled out all other possibilities, go ahead and replace the valve.

***(((NOTE-- It is possible that the valve housing has cracked as well. make sure that the hoses are connected properly during your testing. If there are no hose issues, this will be a defective valve assembly)))

Is the hose washer defective, or possibly loose or can you see if the threads on the hose connection are stripped
Repair Help & Product Troubleshooting for Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Whirlpool Gold Model #GU980SCG52 is leaking on the outside of the Water inlet. The hose is attached on top, but the water is leaking out of the opening on the front side under the hose.


HI. this is a inlet assembly issue. The water inlet valve can be identified by the water hoses connected to it. One hose will lead from the valve to the pump/motor assembly in the center of the dishwasher. Check that the hoses are securely connected ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My GSD900G-01 dishwasher leaks where the hot water is supposed to go into the tub. There's a plastic fitting that seems to be glued to the side of the tub and the hose from the inlet valve goes to the top of this fitting. There are no visible cracks or other damage but there is some rust inside the tub at the fitting. The fitting has two open gaps on it's side which is where the water is leaking out. It looks like the water is supposed to flow past these gaps (which I'm guessing are there to


Hi, I seen where this posted on premium. If you still need assistance, please let me know. I can help you through this.\015\012\015\012Vic ... Dishwashers

Dishwasher is leaking water from top LH front side ,it appears to be coming from where the hose is attached to the detergent dispenser,how can i get the front off to check,Fisher & paykel DS 603


Hi\015\012\015\012To open the front panel, follow the below procedure---\015\012\015\012Slide open drawer.Locate draw pin on either side of the tub.Using a sharp pair of long nose pliers or slip jaw pliers grasp th ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

Dishwasher Leaking Dishwasher leaks from underneath the right front side of appliance. Can't tell exactly where it's leaking from, because of plastic guard/support on underside. All of the connections and hoses are in good shape. I'm assuming that it has something to do with the draining process, as it will leak 2-3 times during a wash cycle. Sometimes it's very little water and sometimes it's as much as a gallon.


Hi there, dishwasher leaking might be due to either of these causes, check these:Main tub sealNote… If the main motor of your dishwasher is mounted vertically, beneath the center bottom of the dishwasher, the foll ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Model MDB5601AWW leaking around the side plastic box on left wall inlet that has water hose. What needs done?


... Maytag MDB5601AWW Energy Star Built-in Dishwasher - White

Water is leaking from the top of the top drawer, mainly on the right side of the top drawer. Is there an adjustment to raise the tub so that it would have an even seal to prevent the water from leaking. I noticed that the top drawer has a bigger gap on the right side or has more give-in/movemenet when the tub is lifted compare to the left side. This casue the flooding error at the end of the washing cycle.


I have had similar problems with my DD603SS. The leakage leads to the water detection in the bottom of the unit and the resulting F1 error. The movement and height of the lid is controlled by the lid actuators. There is one on each sidewall. The draw ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a KitchenAid but model # KUDI24SEWH1. Can not find it on your list although another model without the last letters 'WH1' is on it. Anyway, my nephew ordered the parts he said needed to be replaced. One was the top water feed tube and bearing which he had no problem replacing when the part came in. But, he is having a very difficult time opening up the front door to replace the soap dispenser. Removed the 6 screw (three on each side) and the two at the top of the door but that is as far


You don't Use the WH2 just the first 6 letters and numbers.\015\012Jim ... KitchenAid KUDI24SE Built-in Dishwasher

When I connect the water hose to the pressure washer, it leaks from the bottom. I open it and the leak comes from a white plastic receptacle that is on the left side of the pump.


... Karcher K 5.85 M Electric Pressure Washer

Removed rear toe-plate to detect leak. Leak caused by broken drain hose. Hose replaced. To do this the unit was tipped forward onto its front door to allow access to the base area. Water allowed to drain out the front base area. Unit re-assembled but now does not switch on. Water connected. Base-plate dry. No water was detected at upper-front control panel. Power is connected and reaching unit ( multi-meter test ). Tipping the unit forward seems to be the cause. Is there any fuse,


The micro switches are frequently replaced on the door handle and they don't need to ever get wet. A lot of amp draw burns those switches up while they are dry. If they were wet and power was applied then they got fried my friend. The good news is th ... Dishwashers

Leaking from underneath. Water appears from under basboard to the right of dishwasher, not from directly in front. Only seems to leak during rinse cycle and has just started recently. Removed front panels and noticed the bottom of cabinets on both sides have water damage as if water has been leaking for some time. Never have seen any water until now. GE model GSD500X-66WB. Came with house, approx. 15 yrs old.[


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101\012\012\012,fhjsuj ... GE 24 in. GSD500X Built-in Dishwasher

Whirlpool model # DU1055XTPQ4, type 575-0. It is leaking water from the bottom front and it looks like the seals are tight. There are seals along both sides and the top. Is there supposed to be one at the bottom?


... Whirlpool Dishwashers

I have FGHD2433KF1, and there is a leakage from the splash guard. I open the front cover of the door and noticed that when a large amount of water rushes against the front door, water comes over the gasket and fills the splash guard. The dishwasher stops the water when the water is just about to reach the top of the guard, but sometimes the water comes over the top of the guard. That is when the leakage occurs. I noticed that there has been a replacement gasket for some of the Frigidaire dis


Make sure the dishwasher is level. If the water is leaking from the door, you should replace the door gasket. ... Frigidaire FGHD2433K 24 in Builtin Dishwasher

Frigidaire dishwasher (Electrolux FDB750RCB0) does not move water through the hose to the upper wash/spray bar. The lower wash/spray bar has pressure enough to turn. With the dish washer out from under the counter I can see the water rise very slowly up the translucent hose. If I remove the check ball under the stem assembly in the motor in the bottom of the tub, water flows, but I'm not sure if the top bar turns then (with the door open I see water coming down from the top, but never saw


... Dishwashers

The rubber hose from the solenoid to the rectanglar shaped box on the side of the unit where the water goes into the unit. the rubber hose has water comming out when unattached for the side of the unit, however when reattached water gurgles and sprays out of the rectangular shaped box that takes the water into the unit. unit seems to operate fine, just leaks really really bad from the attachement point outside unit.....


... Whirlpool 24 in. DU927QWD Built-in Dishwasher

Water leak I have water leaking from the second outlet where the drain hose connects to the dishwasher. The part has a rubber top and the water is coming out there instead of the hose to the garbage disposal drain. Is the part bad or is something else wrong.


... Tappan 18 in. MDR251RE Built-in Dishwasher

Water leaks from underneath the unit. Water only leaks when the pump cuts on (pressurizes). It leaks down on to the hose connecting to the water inlet valve on the right hand side of the unit when looking at the door of the unit. When the unit is full of water and the motor / pump is not running the unit does not leak. This unit is a Maytag jetclean dishwasher Model DWU9200BAB about 12 years old


Please change the 'o'rings of drain line and the inlet and also check the drain hose and the inlet if there are any holes in it ... Dishwashers

I bought a used 7 1/2 year old fisher paykel dd603 for my tenant, it worked fine the first time. second time she got F1 code on both drawers. water was in lower pan, we sopped it up and dried it out. also drawer was not seating level but was lower on left side, and insulation had fallen off left wall. all now corrected. but now the top drawer leaks onto floor on left side. it did not leak before repairman came out, we checked thoroughly. repairman says top lid not seating properly and i need ne


I have the same model F&P and just experienced similar problems. My top drawer was leaking due to that "not important" thin white tube. It really sounds like you called a general appliance guy and not a trained F&P repairman. The guy who fixe ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

Smeg DWF612WH dishwasher has developed a leak. Water comes out of the rectangular hole on the side of the water softner used to mount what looks like a level or pressure switch. A few seconds after the fill valve opens water leaks out, not a lot just a small trickle. After the washer has filled and goes ito its cycle, it does not leak again. Over the past weeks the problem has got progressively worse.


... Smeg 24 in. DWF612WH Free-standing Dishwasher

I have a Whirlpool Gold GU3600XTSY0 Model. There is slow water leak from the right side bottom front of the dishwasher. It looks like the water is leaking from a sensor on the bottom. The sensor has a pin protruding that can push up and down...almost like an on/off switch. I am wondering if there is any way to fix this. Water is leaking on my hardwood floors.....


That is your overflow water switch, that tube goes up to the washer, that switch is defective..water from the machine will come thru that hole ... Dishwashers

I have a Kirkland Signature dishwasher produced by GE. The dishwasher is leaking from the top of the tub, where the water enters into the top sprayer. Should the top water inlet hose be tight to the top of the wash tub, and if so what can I use to make it tight?


... Dishwashers

The top spinning paddle on my simpson silencio dishwasher 950 came off. I was able to re-attach it but I notice that there is no hose for the water to enter the top paddle from - can someone please tell me where this hose would go and where I should be looking. There is an opening at the top of the machine but no attachment from there to the top paddle. thank you.


The end of the spray arm should plug straight into the hole at the back of you machine when you push the top basket in. ... Dishwashers

Leaking dishwasher i have an 8yr old hoover dishwasher & it leaks on the rinse cycle. It's coming from underneath on the left hand side as you look at it. I've checked the hoses & clips on hoses, which seem ok. It only leaks as the water is coming into the machine on the rinse cyle. Never any other time, not even when it's filling for the wash cycle!


If your dishwasher leaks, check these:Main tub sealDoor gasket or sealWater-inlet valveHosesMain tub sealNote… If the main motor of your dishwasher is mounted vertically, beneath the center bottom of the dis ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

My Zanussi DS17 slimline dishwasher is leaking from below the door at the front. The inside seals all seem to be fine, but the catchment moulding below the door (which is revealed at the front when the door is opened) is filling up with water, and then overflowing. I can't see where the water is comming from, but it is definitely the water from the washing cycle as it's hot. Any ideas? I haven't dragged the maching out from the wall yet, but I may have to. David R


Hello,\015\012Have a look at the bottom spray arm and check the ends of the arm for splitting as this will cause the water to be directed at the door lower section and leak.Try taking arm out and run for a short while and see if it stops the le ... Dishwashers

Dishwasher leak My dishwasher has a slight dip leak on the copper hose that rund from the hot water. The leak is between the copper hose and its connector nut. I tired fixing it with plumbers tape but it still leked out the sides of the tape.


Tape won't solve this issue. The fitting I assume is a compression fitting which is a ring on the copper pipe that is compressed when the nut is tightened. If tightening the nut won't resolve the issue, then you will need to cut the copper behind the ... Dishwashers

My dishwasher leaks water from the top of my sink when in the drain cycle mode causing a mess on the counter top. How do I stop this leak? The plastic cover to the part which is located next to the faucet is cracked but there appears to be no leaks on the hose or on the part itself. Also, what is the purpose of this part? Is this the actual drain for the dishwasher and if so, why doesn't it tie directly into the drain?


... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1688 seconds