Having problems with your Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher ?

Dishwasher: Whirlpool Gold Quiet Partner. Has worked fine until had a house plumbing blockage which made water pool in the bottom of the dishwasher as well as kitchen sink. Tried to get it to drain at first using keypad. Drain light clicked on and then off because there was nowhere for water to do. Manually emptied most of the water, then "Cancel/Drain" worked if I held it down quite a while. House plumbing is now fixed. However the keypad only works sporadically now. Some buttons do so


Answers :

\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing.
Now this happens because, the STOP Button, is pressed and the "Door Opened", during the Wash Cycle. This should NOT be done. You shouldNEVER TURN IT OFF MID-CYCLE. you should instead, Simply, pull on the handle, to Open the door, the system will take care of everything, after, you close it,and pick up where it left off. The turning OFF, makes the machine "Think" that a New Cycle, is going to be done, before the old one is finished, and resets itself to do it all again. But it still has water, that's not meant to be there so it must dump it out.
Now, the FIX. Take the Dishwasher, out, and tip over on it's side, tip to about a 45' angle. Water will come out from underneath, this is from a small "Overflow" reservoir. this reservoir has an "Anti-Flood" switch. The removing of this water will "Reset" this Switch, and allow the dishwasher to work again.
So what happens, is this, when the STOP button is pressed Mid-Cycle, the machine must "Dump" whatever water is still in the machine, into the "Overflow Reservoir". This water then causes the Anti-flood switch to jam, and this stops the machine, until it is reset,by the above method.
Hi
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons. Usually, these issues are related to\015\012kinked hoses, knocked out disposer unit (if connected with the dishwasher drain\015\012hose) & clogged drain pump & filter. Also note that dishwashers do not\015\012drain completely after a finished cycle and this is normal. Dishwashers are\015\012designed to leave some water in the unit to ensure that the heating element\015\012doesn’t overheat. If you suddenly begin to experience a large amount of water\015\012being retained in your dishwasher, you have a problem. Some of the most common\015\012reasons include that the drain hose isn’t working properly, the drain pump\015\012isn’t working correctly, or possibly there is a plumbing problem in your home’s\015\012drain lines.
\015\012
\015\012

\015\012\015\012First\015\012check whether the drain is not clogged or blocked and the line is not kinked.\015\012Check all the hoses for blockages & also clean the air gap. Has the\015\012disposer been replaced recently? If so, chances are the knockout is still in place.\015\012Simply remove the drain hose from the disposer, and knock out the plug. If the\015\012disposer has not been replaced, try removing the drain hose from the disposer\015\012and use a wet-dry vacuum (prepared for water, of course) to **** any water (and\015\012hopefully anything else) from the drain line. Then reconnect the hose, and test\015\012the unit. If you have checked the air gap and the drain hose and can’t locate\015\012the problem, then it is an issue with the drain pump of the dishwasher.
\015\012\015\012
\015\012\015\012Please do\015\012accept the solution if the issue is resolved or else revert for further\015\012assistance.
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks
\015\012\015\012Rylee

Repair Help & Product Troubleshooting for Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher: Whirlpool Gold Quiet Partner. Has worked fine until had a house plumbing blockage which made water pool in the bottom of the dishwasher as well as kitchen sink. Tried to get it to drain at first using keypad. Drain light clicked on and then off because there was nowhere for water to do. Manually emptied most of the water, then "Cancel/Drain" worked if I held it down quite a while. House plumbing is now fixed. However the keypad only works sporadically now. Some buttons do so


\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing. ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a hotpoint aquarius df23 dishwasher. when i turn it on for a wash there is no water coming into the dishwasher. i have put water in with a bowl and it works as normal until it drains the water out. my washing machine is plumbed in to the same pipework and it is working fine. does the dishawasher have a water pump that may need replacing????


Most likely you have an air lock in the dishwasher.\015\0121. Refill the salt compartment.2. Turn of the water supply at the mains.3. Disconnect the diswashers water hose from the mains supply.4. Lower the water hose and allow ... Dishwashers

The ge profile dishwasher model PDW8280J10SS was purchased about 2 yrs ago. It was working fine up until Jan. 2009. It ran fine but the water stopped draining. I read were you should run the garbage disposal prior to running the dishwasher. I drained the water and did this. It worked fine for a while then the problem was back. Once again, Drained all the water, sucked it out with a turkey baister, moved the dishwasher and checked hoses etc. Once again, it worked fine for about 10-14 runs. It now


It is probably clogged at the pump or before. See if you can get outlet hose off the bottom before the pump. ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

Have a Kenmore Freestanding Dishwasher that was working when hooked up to the sink. When we plumbed it in and connected the electrical directly, we now get an "F4" flashing on the panel with a beeping noise and the pump sounds like it wants to drain but just get a sucking noise. I've tried putting water in it to prime the pump, but still doesn't want to work. Do the codes mean anything, or point to a specific part?


... Kenmore 24 in. 16332 / 16334 / 16339 Free-standing Dishwasher

Our kitchen drain clogged recently and water drained back into our VUD141 dishwasher. A plumber cleared the drain, and turned on the DW - which pumped out the standing water. But now, we have no water flowing into the dishwasher. The drain pumps, the heater works, but there's no water supply. The plumber who cleared the drain said he didn't DO dishwashers, and I cannot locate the owner's manual since we prepared for a move.


Hi\015\012\015\012 \015\012\015\012When the dishwasher won't fill and the water supply is on,\015\012then the issue is with the water inlet valve which is either clogged or\015\012blocked, you can try to clean it. If this wont so ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

My dishwasher DW60 does not complete the program and drain the hotwater leaving hot water in the bottom of the dishwasher however when I run a prewash cold water cycle the water does drain away and the dishwasher program works correctly do you know why it drains cold water okay but not hot water


... Dishwashers

KitchenAid dishwasher KUDS24SEBL does not drain after rinse. It goes through wash cycle, drains water completely , then it fills water for rinsing, runs and after that it does not drain. Cancel does not work after that. Water is very hot inside the tuba t that time. The dishwasher needs to be left for an hour or so before the cancel button can drain the water out.


... LG LDF6810 Built-in Dishwasher

Kenmore dishwasher Food particles left on dishes and inside of dishwasher. All functions appear to be working normally. Water pressure OK, drain OK, water temp OK, Etc. Operating dishwasher though a normal cycle without dishes solves the problem for one load, then back to problem. Dishwasher is about 5 yrs old and worked perfectly for 4 yrs. Any advice would be greatly appreciated. Bruce


... Kenmore 17822 Free-standing Dishwasher

I have a whirlpool DWH B10W. Last week the main drain outside blocked and none of my service machines were working (not draining). The main drain has now been unblocked and every machine except the dishwasher are now working fine. The plumber has checked the drainpipes again and says all are now clear. When I try to use the dishwasher, after the initial drain it stops and starts beeping at me. I have also noticed that no water is going into the machine. What's happening?


The error most likely indicates a Long Drain Sequence (Drain Exceeds 8 Minutes) - Select 'cancel' twice to clear error code. \015\012 \015\012 \015 ... Dishwashers

Water inlet I have a miele dishwasher and water keeps collecting in the bottom tray which in turn makes the water inlet light come on and stops the dishwasher from working. i have drained the water out of the bottom tray which makes everything work again but how can i stop this from happening as it seems to happen on a weekly basis. thanks


It sounds like there is either a kink in your drain hose or your garbage disposal is blocked up where the dishwasher drain is connected ... Dishwashers

Dishwasher control buttons do not work. Machine is stuck on low wash and headed dry. Pushing butttons on crontrol panel do nothing. Dishwasher seems to work, fills with water , you can here it run it's water agitation, and drains, but only works in low wash


Hello,This means the touch pad has failed, you can make this repair it's simple. Try flipping the breaker off for several minutes this may reset the glitch.Applian ... Dishwashers

My bosh dishwasher SHX55M06UC/46 will not drain. A new disposal was put in and the dishwasher drain plug was not punched out and the dishwasher was ran that way. Now it just holds water in the bottom. I've tried resetting or canceling the wash cycle but that doesn't work and the washing cycle works fine. I'm hoping there is a reset or a safety for the pump if it gets clogged.


... Dishwashers

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

Water jet arm does not work water goes into the dishwasher dishwasher drains but the arm does not work the dishes are not getting sprayed with hot water the dishes are not getting cleaned the soap in the dispenser does not all come out


In most units, the movement of the arm is powered by the water. If the water does not come out of the arms, check the filter for debris or the arm itself. This could also be caused by mechanical issues. You may want to inspect the arms itself for ... Dishwashers

Hi, we have a Blanco dishwasher model number BFDW4. The dishwasher has stopped working, it fills with water then stops. We tried cleaning all the filters and we tipped it on it's side on a 45 degree angle to drain the water out of the Overflow reservoir but the machine continues to stop working after filling with water. Please help. Regards. Jayne


Hi,\015\012\015\012Sounds like you may have something jamming the circulation pump from turning. A dishwasher has steps in the cycle to complete before it moves onto the next step. once the unit fills with water it then circulates the wat ... Fisher DS603W / DS603B / DS603I Dishwasher

I have a kitchenaid dishwasher model KUDS01FKSS0 which is not running. For the past 2-3 months it occasionally stopped mid cycle with water still at the bottom of dishwasher but eventually resumed working. Now it just doesn't run any more(and there is no water presently in the dishwasher tub). The user interface part (keypad) seems to be working. I can press the keys and the corresponding LED would light up. However after I close the door, nothing happens. There is also no noise what so ever. A


... KitchenAid KUDS01FKSS Dishwasher

Dishwasher drain is hooked to a food disposer and until recently the unit worked fine. Last week following a cycle a couple of inches of water did not drain out. All food is removed from dishes, silverware, etc. prior to loading and the food trap in the bottom is completely clear. I ran the unit empty through a Lightwash cycle and afterwards the water level (that which didn't drain out) looked to be the same as before. The dishwasher is run 2-3 times weekly whereas the food disposal is


Hi, The I don't think the problem is with the loop and the 32" above the floor.If the dish washer was removed from one house to another, did *********** ever have a dish washer in the house before that he replaced this one with? The reason I am aski ... Dishwashers

I have a kitchenaid dishwasher model KUDS01FKSS0 which is not running. For the past 2-3 months it occasionally stopped mid cycle with water still at the bottom of dishwasher but eventually resumed working. Now it just doesn't run any more and there is water presently in the dishwasher tub). The user interface part (keypad) seems to be working. I can press the keys and the corresponding LED would light up. However after I close the door, nothing happens. There is also no noise what so ever. Any i


THE MOTOR SHOULD MAKE NOISE IF ON, CHECK THE MOTOR OR TIMER. ... KitchenAid KUDS01FKSS Dishwasher

Hi, I have a Kenmore 15879 that is basically working except the bottom water spinner...lol (don't know technical name). The dishwasher pumps the water into the bottom of the dishwasher, will heat the water, but not disperse the water in the spinning sprinkler manner it's suposed to. I've opened the dishwasher in time to see that water is spurting out of the holes about 2" high, but it's just not spinning. The water also drains just fine after the whole cycle.


This is caused by the impeller being clogged or the pump is failing, When the pump is woring properly the water will shoot out with force. ... Kenmore 15879 Built-in Dishwasher

I have a Bosch Dishwasher, Model SHE46C06UC. No mater what cycle I start it in, it simply activates the drain and continues to run without ever starting. Within the last week prior to the dishwasher not working, I noticed a low hum/vibration emitting from the dishwasher. I've clean out the screen and drain filter, removed the pump cover to check for any debris. I've manually added water and it does drain. Additionally, the drain cycle continues to operate even with the door open.


First thing you may want to check is the door switch. You can pull it off and measure the resistance with an ohmmeter. If you get good reading while pushed in and none while switch button is released, then it is a good start. Next, you may want ... Dishwashers

Whirlpool dishwasher ADG 7460 will fill with water ok and wash but will stop before it finishes the cycle leaving water in the machine. if you set it to rinse it will drain the water .... so the drain pump is working ..... water it drains is hot so the element seem ok ..... help


Hello & Welcome to FixYa Dishwasher not draining completely problem usually ... Dishwashers

Whirlpool Quiet Wash Plus dishwasher Model DU920PFGZ3. Worked fine until I replaced the insinkerator and forgot to punch the drain plug leaving water standing on the bottom of the machine. I punched the drain opening, and pushed the cancel/drain cycle button. It drained fine but since no water comes from the spray arms. I have removed the arm all the way down..NOTHING!! Some research indicated it could be the water inlet valve. When the buttons are pushed, it cycles but no spray or water.


... Dishwashers

GE Dishwasher model PDW8200J03BB stopped draining. Removed the drain pump, checked with Voltmeter and there is resistance on ohms X10 of about 3. The flap is in place so water isn't shooting back into the sump inlet. Replaced the sump inlet about 6 months ago because it was deteriorated due to hard water. Pump worked fine after that. Checked drain hoses and air gap. Was able to blow water through. Pump only trickles water out at air gap. Does the pump need replaced?


Clear the line from the air gap to the drain,, if the rest is clear the only thing it can be is the propellers on the pump, i which case you will need to change the pump ... GE 25 in. Profile PDW8200J Built-in Dishwasher

I have a slimline dishwasher from Ikea. The model is Whirlpool DWH C10 W manual. Everything worked fine up until the other day when I switched the machine on and it made a noise as if it was working but nothing happens. No water comes into the washer although inlet pip looks fine. I have poured water in and it is drained okay but the dishwasher is not cleaning dishes. After checking through numerous forum and reading about a flood prevention switch which can be sorted by tipping the d


Ok so slow down and lets look at the d/w problem and don't take the kitchen apart.. in the tank there is a float in the front corner. lift the float and listen for the click that would be the float sw . if no click th ... Dishwashers

Water will not drain from bottom of GE Profile PDW7300 dishwasher. I checked the service mode feature by depressing the cookware and the heated dry keypad simultaneously for 3 seconds and did not hear any activity from the dishwasher when I activated the drain pump and when I activated the main pump. Other service mode features did activate when I checked them (i.e. activate water valve, open active vent, etc.).


... GE 24 in. Profile PDW7800 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1745 seconds