Having problems with your Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher ?

The top rack dishes are not getting clean. the spra arm is clear and the tube supplying water to the arm is clean. the float is also moving freely.


Answers :

Does this have the water conduit tube going up the inside of the rear wall where you can see it,if so,the conduit "horn" where it connects to the tube that feeds water to the upper arm with repeatedly opening and closing this horn wears out and lets water get past here and lowers water pressure to the upper arm
Repair Help & Product Troubleshooting for Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The top rack dishes are not getting clean. the spra arm is clear and the tube supplying water to the arm is clean. the float is also moving freely.


Does this have the water conduit tube going up the inside of the rear wall where you can see it,if so,the conduit "horn" where it connects to the tube that feeds water to the upper arm with repeatedly opening and closing this horn wears out and lets ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a GE Profile, GSD4930X73WW, dishwasher. The upper wash arm is not spraying well at all. I checked the water line from the pump to the upper arm and it's fine. I cleared the filters and cleaned the float. I also took the inlet valve off and cleaned the screen. Although the washer works better overall, the upper arm still does not work well. Nothing appears to be in the upper arm assy to clog water from spraying out. All seems clear from the turbid sensor (next to the pump) through t


... GE Dishwashers

The dishwasher is not cleaning the dishes at all, so far I have done the following: Checked both sprayer arms and they move freely and do not appear to be clogged (I ran stiff wire thru holes in each The float is not stuck and moves up/down easily The water leavel in bottom of tub does appear to be low - so I added water filiing tub to heating coil - however this did not help and the water did not spray on lower or upper racks - this is an older model Kenmore Ultra Wash WHAT DO I NEED TO CHECK N


Heating element may have burned out. Check water temp during wash--should read between 130 to 140 F.If not the heating element,you may have to replace pump-motor assembly or wash impeller.Hope this helps. ... Kenmore Dishwashers

About 3 years ago i bought a kenmore model 665.16264400 dishwasher Never did clean very well.Now upper rack does NOT clean at all. Arm rotates freely,water inlet tube appears clear at end and engages at rear


You probably have a clogged water feed tube. Remove the lower wash are assembly and the water feed tube and vacuum out with a wet dry vacuum. I had the same problem and it was fixed this way. ... Dishwashers

Whirlpool Gold Dishwasher - GU2700XTSB The top rack of the dishwasher is not cleaning. The bottom rack dishes clean fine. There are no clogs in either the bottom or top spinner arms, the plastic tube feeding water from the bottom pump to the top rack spinner arm is clean, the spinner arms all rotate freely and do not bind. Water pressure is correct and water temperature is correct. There are no lime or hardwater deposits or clogs. What could be the issue?


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

It doesn't start and clean light flashes Kenmore Elite dishwasher water supply is turned on overfill protection float is able to move up and down freely there are no sudes in dishwasher soap dispenser is not blocked but it doesn't open turbozone spray jets are not blocked


HiThanks for using FixYa. If the clean light flashes, pauses, and then repeats. When the dishwasher doesn't sense a water temperature increase, it stops working and locks the functions (clean light fla ... Dishwashers

Hi, I have a Miele G638 Plus dishwasher and the Red Inlet/Drain light comes on shortly after the wash cycle starts. I have cleaned everything out and the impellor moves freely. I have also made sure the outlet is clear. I have tried resetting and repeating on different washing cycles but it always locks out after the washing cycle starts. Could this be a heater problem as the element looks quite corroded? I have had side panels off and the water appears to flow easily through the sid


Hi\015\012\015\012Thanks for using FixYa. The first\015\012thing that should be checked is if its draining properly as it could be that\015\012the drain hose is clogged an ... Miele 24 in. G638 Plus Free-standing Dishwasher

We have a Frigidaire dishwasher model #FDB634RF bought new. It was used for a not very long period of time but developed problems due to well water with high lime content. now with good cleaning products available it is ready for use again. The problem is the top spray arm that refuses to rotate. I have taken the arm out and thoroughly cleaned it of deposits checked the supply line from the pump and checked the sump for any obstruction. The arm turns freely by hand but water just pours out the


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Frigidaire 24 in. FDB635RF Built-in Dishwasher

Water problem Hi, I have a Jenn air DW 711 that does not get water. I checked the following: Water line: I unhooked the water line and it is clear & free flowing. Float: The float moves up and down as it should. Filter: The filter inside the tub is clean. The motor runs and will drain any water in the tub I put a bucket of water in the tub and the dishwasher immediately drains no matter which setting I choose. Any ideas? Thanks, Steve


Many dishwashers will drain at the beginning of any cycle. \015\012If the water does not fill after the pump-out cycle, then the problem is either the fill valve or the float switch. You should be able to hear the float switch click as you rais ... Dishwashers

I have a frigidaire dishwasher - model number PLDB998AC1. There are two spray arms in this dishwasher - lower and upper. The lower works fine but the upper spray arms are not spinning. There is what I think adequate water pressure coming in from the top but no movement on the upper spray arm. Here is what I know: 1) The water pressure and spray arms alternate between top and bottom. 2) The upper spray arm moves freely when I push it gently. 3) I have removed the pump and cleaned out an


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

Top arm does not turn in most of gibson amana an frigidaire this is done by ball in bottom of pump .it is clean.spray arm are clean .bottom arm move all the time.timer works it hesitates every so often and so ball will move an water should go up to upper arm but doesnt.common problem on these units but dont know how to cure?change ball.didnt work..on one unit changed pump cure problem for 4 months then returned....also does anyone know were u can buy the plastic they used to sell for dishwashers


Can yo give me the make and model number sol I can look at the service manual for you? ... Dishwashers

Hi, I have a Miele dishwasher G2150 that after 7-10 minutes on any cycle the rinse, dry, and end lights flash amber. I called the 800 number and they walked me through the diagnostic sequence and they said it was an error code 12 something to do with water restriction. I removed and checked the bottom "L" filter(clean), the wheel (moves freely, not dirty), and the grey in line filter screen on the intake hose,( clean also). I can feel the water coming through the intake hose, water comes in thro


... Miele G2150SC Dishwasher

I am not getting any water out of the bottom spray arm in my bosch SGS47E02GB35 dishwasher. I have cleaned out the plastic pipe assembly on the left hand side of the machine and the plastic tubes that sit to the right of the pipes. I have blown through many of the other pipes to and dislodged quite a lot of debris which has now been cleared out of the machine. The machine completes its cycle and water comes out of the upper spray arm (there may not be as much water coming out as there should be)


1. Check that water can flow from main pump,though hose to propellor,that there is no blockage. ... Bosch Dishwashers

The water supply arm for middle sprayer is not held in place by clip that is attached to bottom of dish rack. Does not meet up with water outlet on back of washer and also impedes movement of sprayer arm. Dishes not clean, have greasy film, and residue.


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... KitchenAid KUDS40CVSS Builtin Dishwasher

Do not have any water being pumped into the upper arm spray bar. Removed and checked the feed tube assembly as well as the upper tube leading to the upper spray arm for obstructions and there are none. Also removed the ACCUMULATR and cleaned out the area.


Hi,We somehow got cut off, I am still around, we can chat here if that works for you. The link is here for the clean out ... KitchenAid Dishwashers

Hi, I have a Fisher Paykel DD603I (integrated) dishdrawer unit. The bottom drawer soap dispenser has water in it after it runs (and leftover soap), and there is a small amount of water sitting in the bottom of the drawer. The dishes don't get totally clean. I have removed and cleaned the spray arm, drain filter, filter plate and bottom of tub. Found nothing clogged or particularly dirty. Put all the parts back in and everything moves freely. Ran it empty, and same problem occurred.


Hi Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doe ... Fisher and Paykel Dishwashers

I have a whirlpool GU2700XTSQ1 dishwasher. I have the typical top rack not cleaning problem. I have removed the rear washer tube that leads to the top sprayer, no clogs. Upper arm is clear, lower arm is clear. I also removed the lower cover, checked the chopper screen and inlet, no clogs. There is a screen inside that I cannot get to. It appears to have some sort of paper or cloth sticking through the screen with a 50% block. Perhaps a sticker or label from a dish. I see this screen when looking


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

Two problems: the water pressure in the arms is low. If you pop the door, arms are not spinning as it should. Each time you start and stop, the arms move a tiny bit. Have cleaned the filters and the spray arms completely. Also, detergent door no longer pops open.


Hello, Welcome to fixya.\015\012 \015\012I just came ... Bosch SHU3306UC Built-in Dishwasher

Hotpoint Aquarius dwf34 lower arm not spinning, There is water supply to top arm but none to lower? Lower arm is clean and can freely spin by hand.


... Hotpoint Dishwashers

My dishwasher is not working properly, i have cleaned all the filters and spray arms, but still have food partials all over dishes. I did use a knife to hold down door latch so i could see what was happening when the dishwasher is working. Water does come out of the spray arms but they don't move and the dishwasher is empty, also now the latch won't catch since i used the knife.


Make sure the water temp is not too low. Make sure the pump is not clogged up with debris Check that hoses and spray arms are all clear. Remove spray arms and clean the holes in them. Make sure the shafts spins that the arms attach to. ... Bosch 24 in. SHE44C05UC Stainless Steel Built-in Dishwasher

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

I have a Whirlpool dishwasher model number DU1055XTPQ4 that is not cleaning the dishes. When the dishwasher is working, the bottem arm is turning and water comes out the holes. The middle arm has some water coming out, but does not turn. The top arm does nothing. It appears I have a pressure problem. I took out all the arms and cleaned them, along with the plastic tube that feeds them water. They had some build up on them but not much. I have the same result as before. I took off the


... Whirlpool Dishwashers

I have a 13 year old Siemens SE64630GB. It isn't cleaning items in the upper basket and I believe it's due to lack of water pressure in the upper spray arm leading to little or no rotation of the arm. Have cleaned out the drainage pump and removed and cleaned both the water feed pipe to the upper arm (a lot of gunk in there) and the spray arm itself (which also had blocked nozzles) - no apparent blockages now. Could there be a blockage in the circulation pump and if so how do I access this pump


... Siemens Dishwashers

Top arm of dishwasher does not spin or spray. it is a 7 yr old frigidaire dishwasher, model #gldb957ab. The dishes on the lower rack also do not get clean. this just started recently. the mid level sprayer will turn by hand but doesn't move during cycles. seems like it would be there is no water coming to the top of dishwasher while it is running.


... Frigidaire 24 in. GLDB957A - Multiple Color Energy Star® Built-in Dishwasher

The dishes in my dishwasher are not getting clean, particularly on the upper rack. It seems to be because the upper water arms are not spinning during the wash cycle. The bottom spin arm is working fine. I have cleaned out both upper arms as best as I could without removing them (above and attached below to the upper rack), as it does not appear that these arms are easily detachable. I am thinking maybe water is not making it up the line to the upper arms? I also have a lot of dirt in the b


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. First of all please check the\015\012Water temperature by using a thermometer inside the dishwasher to measure ... GE Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1606 seconds