Having problems with your Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher ?

The washer restarts itself after it finishes the wash/dry cycle


Answers :

Repair Help & Product Troubleshooting for Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Made funny noise; stopped to investigate; then wouldn't restart; followed directions below from FixYa and restarted. It finished the cycle, apparently correctly, except it left a little water in the tub. Also, continued to make a lot of noise--a loud motor hum/buzz or similar. Did not make this noise during dry cycle. Dishwasher is Kenmore Model 665; stock number 16839. Can you give continued diagnostic instructions? Appears there is a cracked washer under the lower wand assembly; th


The solution was nearly correct. The person who answered only forgot to mention that water level and pressure switch must be tested. This can cause drain pump working longer than necessary and humming, and machine underfilling, which can cause noise ... Dishwashers

Dishwasher stuck on rinse cycle. Have three yo son who plays with buttons, but I've been unable to get washer to finish (rinse went for three hrs prior to me realizing it was still running). Tried the front panel buttons w/o effect other than able to turn unit off, but it resumes in rinse cycle. Turned power off to machine from circuit breaker ( w/ machine off) then restarted and still in rinse cycle. How do I reset?


... Miele G892SC SS Dishwasher

The washer restarts itself after it finishes the wash/dry cycle


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My Bosch Dishwasher does not drain all the water out of the dish washer after the finishing cycle...I usually start the washer and then push the drain cycle and it starts to pump for about 10 seconds and stops and starts and pumps again for 10 seconds and stops and then pumps for about 25 seconds and stops....doing this manual drain twice empties the dishwasher of the excess water....what may the problem be?


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

Frigidaire FDB520RHB Dishwashers : We bought this dishwasher about 3 months ago. Today I ran the washer before I left to do errands and when I returned, I believe the washer had finished its cycle. But about an hour later, I noticed it had started up on its own? It then proceeded to run for almost 3 hours before my husband canceled the cycle. We were kind of waiting to see if it would stop on its own, which is why we let it go so long. I think it usually takes about 1 1/2-2 hours to wash. Could


Try to run the dishwasher on a short cycle like rinse and see if it finishes the cycle.It is likely the heater or hot water temperature is not reaching the desired level and this could cause the extended wash cycle. Feel water temperature ins ... Dishwashers

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

Motor makes noise shortly after starting, makes normal sound level during main body of wash, then makes noise again during what I'm guessing is the rinse cycle. Not sure if it is a pump or motor problem. Slight electrical smell noticed after finishing the ''cancel/drain''. Water does not seem to be sprayed around washer during normal cycle, even though water has been in the washer.


Make sure the sprayer arm is turning freely, check for something stuck in the base of the sprayer arm (food or utinsel) preventing it from turning. ... Dishwashers

My last rinse cycle did not completely drain. I have about 1 inch or so of water in the bottom of my dishwasher. I tried to restart the washer, but it will not turn on. I looked for some type of "restart" button, but could not find. My washer is not 4 months old.


... KitchenAid KUDS301V Dishwasher

I have an asko D3450 dishwasher. Washer makes buzzing/humming noise at start of cycle and then randomly through cycle. I checked the sump and pump appears to be clean and impeller spins freely. The cycle seems to work ok. Water is pumping out ok. If you open the door to stop the cycle, the buzzing will continue for a few minutes then stop. If the cycle is restart, the buzzing starts again. The vibrations seem to originate from under the lower spin arm.


If the sound is a bussing - it is the capacitor mounted to the pump. It is failing.Shown here (big white cylinder on right of pic).. ... Asko 24 in. D3450 Dishwasher

I have a Whirlpool ADG937 dishwasher (9 years old) which will not complete a 65c wash cycle. It starts Ok and runs for a long time but then continually bleeps, when I open the door the programme indicator light is on the rinse cycle. If I reset the programme to 65c it may do the same or occasionally it will finish the cycle. I have tried salt top-up, descaling and filter cleaning all to no avail. Is the programmer faulty (can I bypass it?)or should I replace the washer?


... Whirlpool Dishwashers

Yes I have a whirlpool DU1345XTVB1 dishwasher. Just got in July. After each wash cycle the dishes are not dry. I have been using Finish gelpacs w/jetdry & also have a off brand drying agent in reservior to help dry dishes. The water temperature is set pretty hot & washer is draining good. I have tried checking wash cycle a few minutes into 1st cycle to see if water is in filling & heating. Didn't know if maybe heating element going out or thermostat not working? Thank you for your time.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

Bosch dishwasher My Bosch dishwasher finished a wash cycle and was showing the "END" light on, however, the motor was still running as though it was stuck on the drain cycle (there is a gurgling sound from where the eater drains off beneath the filter. Subsequently turning the washer on just repeats the apparent drain cycle with a constant gurgling sound (it does not kick into wash mode). The number on the manual is & 258 (7705).


Is all the water draining from the tub? if not the pressure switch will not reset and it will continue to try and clear it self...check drainage system.\015\0122. pressure switch is jammed on..build up in the sensing chamber..commo ... Bosch 24 in. SHU43 Built-in Dishwasher

Intermitttent beeping on bottom drawer of dish washer no error code only cycle to work all the way through is rinse cycle. Have turned off power supply over night did not fix problem. When you press pause button restarts for about five minutes then beeps again. No problem with top drawer. All inside cleaned using correct powder and rinse aid.


Panel control board Call Encompass Parts 1-800-638-3328 ... Fisher Dishwashers

DISHWASHER WAS IN MIDDLE OF CYCLE... HOUSE LOST POWER AND NOW WASHER STOPPED AND WONT FINISH CYCLE NO LIGHTS ON BOARD DOES HAVE POWER TO UNIT HOWEVER NOTHING LIGHTS UP


Remove the rear panel. Gain access to the thermal fuse. (glass tube like fuse)\015\012This does have a tendency to go bad. A faulty door switch can also cause this. ... Kenmore Dishwashers

Dishwasher has stopped during programme - door may have been opened during cycle??!! - although cycle had only just started. bottom of washer has water in but cant seem to restart on ANY programme - pls help!!! have turned off at power and back on etc - no joy :(


... AEG 24 in. Favorit 80860iW Built-in Dishwasher

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

Im trying to turn on the washer ,but when press the normal cycle button and then start , the lite start to flush and the only thing the washer is doing is draining water, tried couple of times to let the draining finish and it is doing the same thing over and over again.?


... GE 24 in. GLD5500L Built-in Dishwasher

Fisher paykel dishwasher dd601I runs complete normal cycle and finishes normally. 2-3 sec. after completion the washer motor srarts to run and the f1 fault (flood sw. activated) is dislayed. When the power button is pushed the fault spontaneously disappears and the motor stops. no moisture is in thre bottom under the tub and the normal cycle can be ru again with the same results.


Hi\015\012\015\012F1 code indicates an overfill condition which may cause when dishwasher can’t pump out dirty water due to a plugged drain hose.\015\012open dishwasher fully ,dry up as much water as possible the ... Dishwashers

The latch seems to disconnect stopping the washer from finishing the cycle. The dishwasher is Model MDB4000AWA Serial # 15724156UB Pressing on the door seems to keep the cycle progressing. The problem is getting worse.


Dear sir/mam\015\012 please change the door limit switch (door lock) after using for several times the terminals of the doorswitch will be weeken. ... Dishwashers

Whirlpool GU2300 Dishwasher. The machine stops for long periods during the cycle. All lights go out. If the machine is opened before the cycle finishes, it will not resume. If I try to restart, the normal wash light begins flashing. If I then try to cancel, the canel light and the normal wash light flash.


I have reviewed your problem with the Whirlpool GU2300 Dishwasher and have the fallowing suggestions for you.\015\012First, unplug the power to the unit and let it sit for a few minutes. This will clear all internal error messages ... Dishwashers

2 years old but NEVER used it yet. Put on today and it would not run any cycles. Let in water and emptied it out but would not do a wash cycle. All this from start to finish in about 8 mins. Washer kept making this droning noise as if it was trying to do something but couldn't. Checked all the waste pipes and filters - all clean - By the way it was still empty of crockery when I tried to do this. Bosch Model SHV55 MO3GB


Dishwasher have a antiflood device system in the base of the applince try a tip the machine backwoord or sideway if water comes out the base you have a leak generally associate wit a failure of the seal around the impeller of the motor or the microsw ... Bosch Dishwashers

Frigidaire fdb1500lfco stops mid cycle and high temp light and heat dry light flash, does not ever restart to finish cycle.


... Frigidaire Dishwashers

My Whirlpool Dishwasher ADP931 has stopped working. It stopped in the middle of the cycle with 2 to 3 inches of water on the floor of the compartment. I mopped out the water and tried to restart the dishwasher. The green "on" light now comes on when I press the start button. but nothing happens (no motor comes on,no water enters).Repeating the above action several times does not help the washer to restart even though the other function lights will come on when the knob is turned. saturn1914


Hi,Whenever you see such symptoms, Time for you to investigate it properly. Check the below guide :-\015\012\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is\015\012there power getting to the dishwa ... Dishwashers

Portable dishwasher stops 1/4 way thru' cycle. If I shut it off and unplug it for 1/2hr then restart it finishes the cycle. Could this be the timer? GE model # GSC3404G00WW purchased October 2002


... GE Dishwashers

I have a ADG450 about 7 years old, the problem is there is dirty water left at the bottom of the dishwasher after finishing the cycle and the dishes look as if they have had the final rinse in the dirty water. also i have tried the rinse cycle with no dishes and all the rinse water had not drained away. I have cleaned the iside of the washer and where the water goes to the pump. Any ideas


Check the pipe leading from the dishwasher to the outlet, maybe under sink. this needs to be raise up as water will flow back into washer. Had this problem myself, felt foolish when the repair man just tied it up and left. ! ... Whirlpool ADG450 Slim-Line Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1302 seconds