Having problems with your Whirlpool Gold GU2275XTVy Dishwasher ?

Display lights staying on

\015 The dishwasher display lights have begun to stay on all the time. Adaptive wash, rinse only, 4 hour delay and start cancel lights are lit dimly. This morning the machine did not drain. After turning the circuit breaker off and on, it finally drained. The blue lights continue to remain lit all the time now.\015

Answers :

Repair Help & Product Troubleshooting for Whirlpool Gold GU2275XTVy Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a kenmore DW model 16019. The clean Light stays on the light does not turn off. I have tried to disconnect and have taken the motort apart to make sure everything is clean. What Can I do to solve this problem? 1. Does the washer work at all? No it does not work 2. Does it display any codes or flashing lights other than the CLEAN LIGHT being lit? no other lights are on except for the green blinking light 3. Is the light solid or blinking? blinking Green light 4. Entire model # is necessary


Thanks for re-posting with all the info!!The model # is 665.16019403The cleaning light blinking is a fault code listed in the tech. service sheet, its usually a faulty heating circuit.The sheet can be found behind the ki ... Kenmore Dishwashers

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

Display lights staying on


... Whirlpool Gold GU2275XTVy Dishwasher

My Bosch dishwasher SGS46E26GB/90 makes a knocking noise when started. the timer does not advance and the check water light comes on.There is water in the bottom (up to the bottom of the door) . If I reset the DW the water drains ok. If I mess with the buttons E3 shows on the display the 'quick' light stays on and the eco light flashes. I've checked the filter where the water hose is fastens to the rear. I've cleaned the filters at the bottom of the DW and cleaned out the pump area under them.


... Dishwashers

Miele Optima G 2430 - The dishwasher will pump water in for 5 seconds with the Intake/Drain light flashing 5 times. Then the light stays on for 5 seconds and it does nothing. This process is repeated for about 10 minutes untill the washer is filled to the just below the door with water. Then the washer starts running for about 1 1/2 minutes and drains the water. Then it all starts over. If I let it do this for a hour - The display reads F12 with the Intake/Drain light flashing.


Hi\015\012\015\012The first thing that should be checked is if its draining\015\012properly as it could be that the drain hose is clogged and needs to be cleaned.\015\012The drain pump also should not be clogged. ... Miele 23 in. Novotronic G841 Built-In Dishwasher

GLDB958AQ0 Lights on panel light up then go off after a few seconds upon startup. Sometimes they stay on and the timer in the display window counts down the minutes, but in either case no sounds come from the dishwasher nor does any water enter the unit. The water is turned on and there are no kinks in the supply line. I removed the water valve and could not blow through it. Upon applying current to the valve I could blow through it but it still seemed restricted. Should I be able to blow thr


... Frigidaire 24 in. GLDB958A Energy Star® Built-in Dishwasher

Dishwasher fault FP918TD intermittently stops mid-cycle with error; on display. Hot fill light stays on.


Need to replace motor ... Dishwashers

Put detergent in a dishlex dishwasher now the pump stays on a& the dishwasher does not work, just displays a flashing red eco light


Hello jack SparWelcome,You said, Put detergent in a dishlex dishwasher now the pump stays on a&\015\012the dishwasher does not work, just displays a flashing red eco lightWhat is the BRAND and MODEL Number and year of ... Dishwashers

Double dash on display and when put in service/maintenance mode, all the lights came on and stayed on overnight. Still not working until I tested the door switch. It looks like poor engineering on the design. Plastic bar that depressed the door switch was not pushing all the way. It appears that the bar was bent to compensate for the too close tolerances and after the depressing of the switch for six years it did not reach anymore. So I got hair dryer, heated the plastic bar and bent it down to


... Kenmore 24 in. 15932 Built-in Dishwasher

Countdown display is flashing saying 2:10 but dishwasher does not respond to pushing any of the buttons (light stays on Power Scrub and does not respond to selecting other wash cycles). On'Off button works but none of the other buttons responds. Machine does not begin washing when door is closed


... Bosch SHE6AP0 Builtin Dishwasher

Lights on Dishwasher light up but nothing happens. When I reset power it lights up the high temp and sanitize button light up and LED displays PF. After I open the door they stop flashing. the far left five buttons light up when I push them and a corresponding number displays on the LED screen. the only lights that do not come on are the Delay button and power button. Don't know if they are working or just don't light up. No matter what lights up the unit does not turn on....:( ? help can't fin


Pf is power failure\015\012 your loosing voltage to the unit \015\012it may just be the door switch or it could be in the control\015\012 try starting the unit but keep your hand on the unit pushing the door in place,, its not a g ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

I have the kitchenaid dishwasher model #kudv03ctss0.the clean light stay blinking and when i hit the start it just blinks and then stops but the clean light stay blinking constantly.if i hit the cancel button i hear a um noise as if it going to turn on but nothing happens and the light stays blinking. what do you think might be the issue .


Dear friend,\015\012ngfam at you service! happy to assist!\015\012It's an electronic problem!The lights are called codes and need to be diagnoed by a factory service person!!We sell appliances for 65 years an ... Dishwashers

Hi, I have a Kitchenaid KUDI01TJWH0 dishwasher that failed. Any of the front control buttons like Heavy-Normal-RinseOnly or even the HiTemp-EnergySaver .... when you press any of these, the corresponding light for it will blink three times and go off. Normal operation that light for that button will come on and stay on. but none of the lights stay on. If you press start, the 'water heating' light will come on and you will hear the pump run for about 10-15 senconds, and then everything goes off


Hi Your Problem is Probably The Control Panel. Not The Electronic Control. The Plastic Piece Across the Top of the D/W, Which Tells the Control What to do But You Must Realize These Parts Can Be Very Expensive. John H. Been in this Business 35 Yrs ... KitchenAid Dishwashers

I have a Frigidaire Model Number GLD4355RFS1 Serial Number TH80493988 Dishwasher. It quit working when the Rinsing Agent Low light came on. We filled the rinding Agen dispenser with hopes that it would come back on. The Rinsing Agent Low light went off but the unit never came back to life. When the room is totally dark, you can just barely see the lights in the LED display and other lights. It will not come back on. I tied turing the power off and the "PH" alert is displayed in t


... Frigidaire Dishwashers

DS-603 lights keep blinking, won't stay turned on.


Hi. I am unable to help you fix your problem, however I have just had this problem with my dishwasher exactly the same model. I was wondering if you have fixed this problem yet and if you have how. ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

"Light Dry" light flashes 5 times & odd light displayed


Maytag website...all the help youll need ... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

Whirlpool adg 6552. will not start, green lights stays on rinse, red light in the shape of an s also stays on.


... Whirlpool Dishwashers

Good day, My Kenmore ELITE washer's CLEAN light stays on after last cycle and now won't go out. Cannot run the machine at all now that this light stays on. Any ideas?


... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Have a 665-16293201 dishwasher with electronic controls and smart sensor. Approx 10 years old in great shape. it just started having a problem - it takes a long time for the sensing to be completed at the start of a wash and then the washer will start and display a time - like 92 minutes - turn the sensing light off, then start to wash and count down. when it gets to 86 minutes, it starts to sense again and will continue washing while displaying 86 and with the sensing light on. It will keep


... Kenmore 24 in. 16293 Built-in Dishwasher

I have a magtag quiet 100 series that has a broken handle but still shuts tight and seems to lock yet. Problem seems to be that the rinse only light will stay on for quite a long time and won't let me hit the wash button. When the rinse only light does go off, if I hit the wash button it starts but then switches to rinse only. Sometimes I can get lucky and get it to stay on wash after the rinse button is off for some time. Any suggestions?


... Maytag 24 in. DWD1500A Built-in Dishwasher

Have whirlpool gold dishwasher made in Mexico, the control lock light stays on, when i push it and hold it just blinks three times and then stays on steady and then does the same over and over, before it did this I noticed the lights for different cycles flashing randomly, and even pushing cancel button once in a while would start the machine up....I have tried to unplug the machine and then plug back in, but nothing is helping....any ideas??


... Whirlpool Dishwashers

The doorlock light has been staying on for about a week although the dishwasher would still work. Now it will not do anything and the Lock on light is staying on except when the door is open. can you nhelp me. Thank you, Steve


1. Press the Heated Dry pad for three seconds.2. An indicator light next to the lock graphic willilluminate when the controls are locked.To Cancel:1. Press the Heated Dry pad for three seconds.  ... Dishwashers

I have a Kitchenaid dishwasher model KUDV24SE. The "door open" light stays on. I have tested the switch on the door and it appears to be working. There is nothing blocking the door closing, the light just stays on which prevents the dishwasher from working. I am technically astute, just can't solve this problem (yet)..


... KitchenAid KUDS24SE Built-in Dishwasher

The key lock light stays on. I held the heated dry button for 4 seconds and the light still stays on. I think it may be the control board, but I am not sure. Can anyone help me please?


If the light is blinking, it is definately a stuck button and the console will need to be replaced. If it is on steady, it could be a console or control board problem. There are no troubleshooting tips to figure out which one is faulty, the manual sa ... Whirlpool GU2400XTP Built-in Dishwasher

I have a KitchenAid KUDS01IJ Dishwasher. The Rinse Only light is blinking and cannot be turned off or switched to another setting. Multiple presses of the Cancel/Drain button will sometimes have the display show '2' or '---'. A few minutes later the display goes blank and the Rinse Only light starts to blink.


... KitchenAid KUDS01IJ - Multiple Color Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0754 seconds