Having problems with your Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher ?

I have a Whirlpool Gold Series dishwasher GU1100XTLQ1 and it has a flashing light on the control board. When I hit the cancel button it flashes as well. What could be the problem.


Answers :

Repair Help & Product Troubleshooting for Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Whirlpool Gold Series dishwasher GU1100XTLQ1 and it has a flashing light on the control board. When I hit the cancel button it flashes as well. What could be the problem.


... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

KUDP01ILBS6 Kitchenaid dishwasher Doesn't work, except flashing lights on front panel. I have the normal light flashing. When I push any other button the cancel light starts blinking as well. I replaced the fuse, the main control board inside and it still doesn't work. Push button panel next fix? This is getting expensive. Could it be something minor? The troubleshooting papers didn't provide much guidance.


The first thing I would check is if the dishwasher is properly connected\015\012 to power input. There is a junction box under the dishwasher. To get \015\012access to it you have to remove the bottom panel. The power cord should \015\012be connected ... Dishwashers

We have a Kenmore Ultra Wash Dishwasher Model number 665-13859K601. The Normal wash and the Cancel (drain) buttons are flashing red on the control panel. No matter what we have tried, we have been unable to correct this problem. Obviously the dishwasher does not function. When you close the door the lights keep flashing and no button combinations seem to do anything. I have looked at the troubleshooting guide that came with the dishwasher, however there is no


... Dishwashers

Good morning. I have a KitchenAid KUDM01TJ with a constantly flashing "Rinse" light. when I hit the "Cancel" button, it too flashes in the same time with the Rinse light. I left the machine alone, came back a few days later and saw that the issue had resolved itself - but I didn't use the machine. A few days later, the "Rinse" light was flashing again and naturally, I hit "Cancel" to see if the same thing happened and it did. This time the lamps are still flashing. I read through the other repo


No its not the problem of button secquence.its the problem of keypad circuit this is creating this problem.as the circuit is getting overheated and it stops working.the key pad sometimes functions and sometiomes doesnot.in this case the key pad circ ... Dishwashers

Whirlpool GU1200XTKB dishwasher has flashing delay light...unit will not start no matter what buttons on control panel are pressed. The control board has been replaced...same problem. Any ideas I could try next?


... Dishwashers

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Model #PLD4555RFC0 The control panel lights on the front are all flashing and start cancel button will not change anything. flashing Er with wash, dry, clean, and and S showing. Top controls have China/Crystal light flashing and Low rinse agent light flashing. Nothing seems to work


... Frigidaire Dishwashers

I have a 8 yr old model 16879 that stops apparently during the drain cycle. At this point the lights on the panel flash in what appears to be a coded sequence. Pushing the cancel button seems to try to start the motor for draining but immediately shuts off. Do I have a controller problem or something in the motor/pump area? David


Hi,It could be either...I would tear into the drain pump first and verify that nothing is stopping it from turning, then go for the controller if that seems to be okay...\015\012Dishwasher Problems - ... Kenmore 16879 Built-in Dishwasher

Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than


... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher

Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che


... Dishwashers

Kenmore Ultra Wash Dishwasher Model 665.15779 LOCK ON light blinking on control panel, unable to use washer. If buttons were locked, LOCK ON light should be lit continually not flashing. If you press and hold NO HEAT DRY button to disengage lock, nothing happens. If you press the CANCEL button it begins to blink in unison with the LOCK ON light. How can I stop the light from blinking to allow button function again?


... Kenmore Dishwashers

I have a Maytag QuietSeries 300 dishwasher. My original problem was with the control panel lights not coming on. Another repair website recommended replacing the circuit board. We replaced the board, but it did not solve the problem & the dishwasher would not work. Replaced the control panel. Lights come on, but when the start button is pushed "21" flashes on the time display. What do I do?


HI,Just visit this link HERE and your problem will be solved.Goodluck,Please don't forget to rate the solution. ... Dishwashers

I have the Quiet Partner II, DU1100XTPB7, and have already replaced the electrical ciruit board but having the same problem. When I hit any wash cycle button, the soak/scour & heated dry buttons light up, but will not "start." The "rinse only" button does nothing, but if I hit the "delay" button, then the soak/scour, cancel, and also the status buttons, washing & drying, all night up at once. The only button that seems to be working is the "cancel/drain." Although there's no water in the mac


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Dishwasher Kenmore Ultra Wash model #1777990 the 2 hour delay light is on and when I try to cancel the door lock button starts flashing I hit cancel and open the door and shut it and the 2 hour delaay button cmes on and will not go off. Is there a reset button anywhere.


... Dishwashers

My kitchen aid dishwasher will not start I replaced the interface control board thinking that was the obvious problem. When you go to set the dishwasher to start some of the settings don't always light up then when you push the start button the lights will flash then start but it's not flashing and won't start. I get lucky once in a while and get it to flash then start. I don't know where else to look. I don't want to start replacing parts one at a time till I get lucky. My model # is KUDIO1F


Check all cables especially the ribbon cables from the user interface to the electronic control assembly as steam from dishwashings will create small amounts of corrosion and inhibit signals to and from these 2 components,unplug each,inspect,and reco ... KitchenAid Dishwashers

I have a Kitchen aide dishwasher Model KUDI01ILWH6 that will not turn on..there is a control lock light on and I have tried pushing the cancel button but all that happens is the control lock light flashes 3 times and the dishwasher still wont turn on....Please , how to I disengage the control lock


... KitchenAid Dishwashers

Hi i dont know the model of the dishwasher.. but the controls are fairly staright forward... a little knob for temperatur control and an on/off button.. and a light that lights up green when dishwasher is switched on... now the problem is as happened recently, when you switch the washer on greenlight is on and washer can be heard doing something but after a minuit or so the washer stops and the green light flashes. open up the dishwasher no sign of water or that it has done anything at all... th


It sounds like your washer is not getting enough water to start. If your washing machine is filling too slowly or not at all, then you probably have a clogged screen on the back of your washer. To check this: \015\012\015\012 ... Whirlpool Dishwashers

I have a blinking cancel light on model GU1200xtlt1 and will not start in any cycle. Also if I push another button it flashes rinse button and cancel button. Before this it ran in Sani Clean over and over again and I could not change the cycle. I emptied out a bit of water from the bottom because it did not drain also and the water was not smelling too good.


... Whirlpool Dishwashers

Quick Rinse light was flashing at end of cycle. Opened and closed door and pushed Start. Quick Rinse and Cancel/Drain light are now flashing and machine won't start. Turned off power supply (30 seconds) / turned on power supply and then tried again to start the dishwasher, but same problem. Control panel seems to be frozen at the Quick Rinse/Drain mode and will not cancel. Help! Thank you


Ok try this, open the door and then hit these buttons in the following combination. HI TEMP - DRY - HI TEMP - DRY...then close door and press cancel...then wait for the pump to shut down. you should be able to run a cycle after this...If this fails ... Dishwashers

LFT 114 Hotpoint dishwasnher. Two flashing lights on the control panel. Light 1 & 2 are flashing. The machine is not working! Could you advise us what the problem might be.


... Dishwashers

I have an ADG7550 whirlpool dishwasher. Am experiencing a fault when placing on a normal 65 degree programme it starts to fill and then defaults to pre-rinse and the start button and light flash eleven times. Can you explain what type of fault this could be ? I have had a similar problem 12 months ago when it was described as a water pressure problem which again was in the winter and wonder if this is the same. I would add that if I re-set the start button by holding it down and then re-start


... Whirlpool Dishwashers

Start light keeps flashing but washer won't operate. Tried to reset by hitting cancel button but start light keeps flashing.


Check whether inlet water is flowing into the machine. ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

Kitchen Aid KUDIO1ILBS5... Normal Light keeps flashing green and wont start. When I press the cancel button, it flashes too. If I hold down the cancel button fashing light goes away on cancel button, but not the normal button... It continues to flash.


Hi,\015\012\015\012Close the door and to cancel that just press high temp and hetaer dry,then again high temp and heater dry and all the lights is going to light up, it getting into test mode.After that press cancel.\015\012 ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a GE Profile Dishwasher (PDW9200N00WW). A red light for the smart dispenseer of soap just appeared in the status area of the control panel (to the left of the reset/start button). I could find nothing in the manual addressing that and I recently refilled the soap dispenser. What does the red light mean and why doesn't the red light go off? I only had enough soap to fill it halfway and will get more to completely fill it. Is that the problem--only half full?


... GE Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1678 seconds