Having problems with your Whirlpool GU1200XTLS Stainless Steel Dishwasher ?

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Answers :

Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take the wires off to check . If it does not ohm out that is your problem , replace for the fix. If it does ohm out it could be the board or the motor. Let me know how this goes , if its another problem I can still help.
\015\012Phil
Repair Help & Product Troubleshooting for Whirlpool GU1200XTLS Stainless Steel Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

Have GE Monogram ZBD6880 dishwasher. Ran unit and unloaded. Went to use the next day, and none of the buttons to select and start will work- it is as if the unit has no power. I confirmed that there is power to the unit. Is there a way to reset, seems like it might be something simple.


... GE Monogram® ZBD6880NSS Stainless Steel Dishwasher

I have a maytag dishwasher model MDB8600AWQ that suddenly stoped working, no power lights on panel. I have had multiple problems with this unit with a complete service approxinamtely 1 year ago and had no problems until there just seems like there is no power to the unit. It is used infrequently and has been wwll maintained. Is there an easy solution or should I just give up on this unit.


Please refer to the diagrams on this site. \015\012\015\012If the ... Maytag Dishwashers

Own a Frigidaire Dishwasher Model Number FDB4315LFSO and now after about 2 years suddenly the display will not light and function anything. Without pulling the power panel off the whole line circuit seems to have power as they have my disposal unit tied into same electric line and that runs and so does everything else and no breaker is tripped. Is their a reset somewhere to check or any ideas what can casue the display panel not to function any commands at all. Nick


... Dishwashers

I removed an old dishwasher and replaced it with this GE 24" Profile GSD533ODO1WW unit. It seems to run through the cycles like it should but it doesn't seem to run any water for some reason. I hooked up a new water line to it and turned it on. There where no leaks that I could see. Is there any installation manual that you could send me to make sure that I didn't miss anything or is there anything that you can tell me that I should look for? Thanks, Jesse


... Dishwashers

My SB908WL Westinghouse dishwasher is tripping the switch when it goes to pump out the water. What are the likely problems and solutions please! If anyone has some expertise that would be great. (I have recently checked the soldering on the main panel and touched one point up, the rest are fine it seems). The element is working as there is hot water in the unit. We have small kids so maybe something is jammed in there? How do I get access to check. All input helpful. Thanks!


... Dishwashers

I have a Kitchenaid KUDIO1DL white dishwasher which is a few years old now but has worked great since I bought it. Today it has the lean light flashing and will not turn on. there is power, and the drain button seems to work, but I can not get the cycles to come on. When I press the start button, I just get two dash lines and then the unit turns off. Thanks


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e


The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher

I have a Honda xr2600 power washer. When I tried using it, water was squirting from the top of the gun. I took it apart to find that there are o-rings on top of some kind of washer---looks like a lock washer but it's made of cardboard??? Two of these washers were broken. I can get the o-rings but I can't seem to find the washers. I tried getting the manual for this model on line with no luck. Any assistance will be greatly appreciated.


The washers that you describe are made of teflon and are split to facilitate installation and/or allow expansion as they wear. These washers are actually seals and at times are used together with orings to seal high pressure. You should ... Honda Pressure Washers

The control panel on my Maytag MDBH970AW is unresponsive, and the latch is stuck in the "open" position (the plastic piece stays pushed in to the handle and won't come down). I've checked that the unit is getting power from the house. Last time I had this exact problem (when it was under warranty), they had to replace the control panel, the latch, and it seemed like most of the door. What should I do?


... Maytag 24 in. MDBH970AWS Built-in Dishwasher

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

Opened door and unit did not have electrical power (lights did not come on either unit). Called serviceman. He stated there was no electricity to unit(s). Called electrican. He stated wiring to the dishwasher had power. Called serviceman again. He came out and dishwasher worked. He did nothing to it. I opened the door and the lights(buttons) came on. Unit worked for a few days and this morning, there was again, no power to the unit. What is likely wrong with this dishwasher?


... Fisher DD603B / DD603W / DD603H Dishwasher

Bosch APEXX model number SHY99A05UC/14 lost power. Power input line appears to have arced (white power line and wire nut show signs of stress). The power breaker did not throw at the junction box. Already cut back wire and re-attached new wire nut along with replacing the breaker at the junction box. Still no power. There are no other visible signs of power stress or water damage underneath the unit or inside the doo panel.


I do not have access to the user or service manual for this model.\015\012However, such symptoms could be result of heater element or thermal overload fuse blowing. Do you remember having a very hot dishwasher when the it lost power.\015 ... Bosch Dishwashers

Viking VUD040 dishwasher seems like no power


My viking dishwasher only runs for about a minute and then shuts off. Circuit breakers are not the problem ... Viking 24 in. Professional Series VUD040 Stainless Steel (Premium) Built-in Dishwasher

Odd operation Unit turns on, slowly heats up. When wash cycle starts, temp drops 20 degrees. Unit never seems to drain completely. when cycle finishes, Booster heater temp can drop as much as 40 deg (122F) Heater slowly recovers, but unit never seems to go into rinse cycle.


This unit is a sanitizer, not a full fledged dishwasher. It is designed for restaurants and bars where the primary use is washing glassware. The behavior you describe is normal for this model. The manual can be found at the following link: ... Hobart 24 in. LXIH-3 Built-in Dishwasher

My Hotpoint diswasher suddenly stopped working last night. It seems like it has no power to it, as the motor or pump does not seem to come on at all. Obviously when I get home from work, I will check the obvious first - making sure it has power to it, connections are secure etc. (I had a wire break before) If it does have power, I would assume checking the door switch and timer is next. Any suggestions, and any suggestions for checking the door switch and timer??


Sounds like your on the right track. I would use an ohmeter to check the resistance of the door switch by placing the meter probes on each side of the switch. Test while opened and closed position. Same with timer ... Hotpoint Dishwashers

The dishwasher doesn't seem to have nearly enough water in it. The upper sprayer arm doesn't seem to be spinning when running (I open the door and look really quick) and the lower one looks like it barely spins and barely sprays water. The dishes are barely wet and the soap is just laying on the bottom. The water is on, there are no kinks in the supply line. It sounds like it is running, and pumps pumping, but being brand new I am not sure what it should sound like. It certainly doesn't sound li


I would lift the drain pipe higher. approx. 1/2 the height of the dishwasher . also rechack incomming water supply. Make sure no blockages and the like. Try again. ... Bosch Dishwashers

Our KitchenAid Superba model KUDS01DJss0 ( about 7 years old and has always worked fine) I think is not heating . . the dishes come out wet and don't seem very clean if they had especially if they have a small a bit of something like peanut butter on them when loaded ( so lately I've been dong a pre-wash by hand). Unit doesn't seem to get very "hot" during the wash/dry and steam does not billow out when I open the door soon after the cycle completes like it used to. It does feel warm to the


Hello. The new heating element will come with a new control board. There are no tricks to the change actually, the easiest way to change the heating element is to unhook the plumbing, electrical, and drain hose then pull it out and get to the back ... Dishwashers

Humming noise i have a GE nautilus GSD2200 model which has not been used more than 4 years that is giving me trouble.  it's making a loud humming noise (the noise comes and goes, comes and goes) which seems to be coming from the motor area at the bottom of the unit.  I stopped it in the middle of the cycle, but the water seems to be stagnant at the bottom.  any suggestion on fixing the problem myself?


I have seen this SOOOOO many times in my 35+ years in the appliance repair industry.......it is very typical....here you are this is an answer I provided someone with the exact problem not to long ago..............This is a t ... GE Nautilus 24" Built-in Dishwasher

Maytag Dishwasher I would like to know the proper water level after DW fills. Older Whirlpool units a quick guide was when water just covered heater. I have a new D/W and the water supply is difficult to access, there is a kink in the water line slowing the water flow. The D/W fills to bottom of heater, but because the unit is so quiet I can't determine if it is timing out or working properly. I intend to repair water line when counter work is done. Thanks for any help Gary


Newer Maytags should fill close or up to the heater not over. Sounds like your alright for now but I would get that water line fixed. ... Maytag 24 in. MDB8951AWS Stainless Steel Built-in Dishwasher

The rubber hose from the solenoid to the rectanglar shaped box on the side of the unit where the water goes into the unit. the rubber hose has water comming out when unattached for the side of the unit, however when reattached water gurgles and sprays out of the rectangular shaped box that takes the water into the unit. unit seems to operate fine, just leaks really really bad from the attachement point outside unit.....


... Whirlpool 24 in. DU927QWD Built-in Dishwasher

Removed rear toe-plate to detect leak. Leak caused by broken drain hose. Hose replaced. To do this the unit was tipped forward onto its front door to allow access to the base area. Water allowed to drain out the front base area. Unit re-assembled but now does not switch on. Water connected. Base-plate dry. No water was detected at upper-front control panel. Power is connected and reaching unit ( multi-meter test ). Tipping the unit forward seems to be the cause. Is there any fuse,


The micro switches are frequently replaced on the door handle and they don't need to ever get wet. A lot of amp draw burns those switches up while they are dry. If they were wet and power was applied then they got fried my friend. The good news is th ... Dishwashers

I have a General Electric Potscrubber dishwasher. When the cycle is finished, the water does not drain into the sink.I turned the unit upside down to look into the bottom. The motor turns freely. The instruction sheet I found in the bottom of the unit said to remove the filter screen and check the piston valve. I looked at what I thought was the piston valve, but I'm not sure how to check it. The line to the sink seems to be clear. The model of my unit is GSC3230Z03WW. The serial number is AZ627


... GE Dishwashers

The engine starts cold after 2 or three pulls, runs ok initially, but seems to have slightly less power. After a few minutes I can turn off the choke. When teh engine warms up and runs for about 15 minutes, there is a definite power decrease and the motor sounds like it will stall. If I paly with the choke, it does not stall, but has little power to pump water. If the engine does stall or it is turned off, it will not restart until it cools down.


I would first try draining the carb bowl, if you look at where the choke lever is and look below that you should see a clear red tube with a flat head screw below that, if you just turn the screw out the carb will drain. If you still have an issue yo ... Karcher G3025OH Pressure Washer

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1376 seconds