Having problems with your Whirlpool GU1200XTLS Stainless Steel Dishwasher ?

Within the last month our GU1200 is noisy and not getting the dishes clean....I did pull out some melted clogged debrise from the "dish module". WOndering if something else is still in side? and how do I dismantle the lower spray arm to get inside and see?


Answers :

THERE SHOULD BE SOMETHING HOLDING IT DOWN, JUST BE SURE THAT YOU REMEMBER THE SEQUENCE OF PARTS. THE MELTED PARTS ARE FROM THE DRY CYCLE WITH PLASTIC LAYING ON THE ELEMENT. SOMETIMES THERE IS A PLASTIC THREADED PIECE OTHER TIMES IT IS A METAL SCREW HOLDING IT. I WILL SAY IT AGAIN IF YOU ARE UNCOMFORTABLE DOING IT, GET HELP.
Repair Help & Product Troubleshooting for Whirlpool GU1200XTLS Stainless Steel Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Within the last month our GU1200 is noisy and not getting the dishes clean....I did pull out some melted clogged debrise from the "dish module". WOndering if something else is still in side? and how do I dismantle the lower spray arm to get inside and see?


THERE SHOULD BE SOMETHING HOLDING IT DOWN, JUST BE SURE THAT YOU REMEMBER THE SEQUENCE OF PARTS. THE MELTED PARTS ARE FROM THE DRY CYCLE WITH PLASTIC LAYING ON THE ELEMENT. SOMETIMES THERE IS A PLASTIC THREADED PIECE OTHER TIMES IT IS A METAL SCREW ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

I noticed water leaking underneath my dishwasher through the floor joists to my basement. It was a small but steady drip through the joists. I turned off the water to the dishwasher and the leak stopped. I looked inside the dishwasher and there is still some standing water inside the dishwasher, but I cannot see anywhere that water is standing under the dishwasher. I am wondering if the leak is at the pump or at the door? But I see no evidence of the seal leaking.


This is probably the line that goes from the water inlet valve on the bottom of the dishwasher up to the valve leading into the dishwasher itself. It is probably a black corrugated rubber line. This is an extremely bad design, but the solution is s ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

My whirlpool dishwasher is not washing the dishes properly. when finished cycle, I still see the dishwasher tablet half used. The grey long piece at the back, seems to have come out of the two holes it fits into on the "floor" of the inside of the machine. I've clicked it back into place, but it still pops out. Sometimes the rotating sprayer at the top and bottom, don't move either when its out of place. please help.


... Whirlpool GU2400XTP Built-in Dishwasher

Kenmore Dishwasher doesn't rinse? It sounds to be working fine, however, at end of cycle, dishes are still dirty, and the front door on the inside is still dirty. Obviously there is a problem here maybe with water pressure or something. There is steam at end of cycle, can't tell about water other than that.


Try opening the dishwasher during the wash cycle stop it and open it if water is in the bottom it is filling whn you open do 1 or 2 times to check to see if spry arms are spinning if they are check to see if soap dispenser is working also use dishwas ... Kenmore Dishwashers

DIrty Dishes SO i run a load a dishes through the diswasher and they dont come out clean. The original waste is gone but has been replaced by what looks like blended waste from the garbage diposal. I am wondering how you can declog the hose??? Or is it something else??? Thanks for your help.


Try running it through empty with some cleaner in it check all the in side for anything clogging it and then if you can put some hot water in it to loosen any grese ... Hotpoint HDA2000G Built-in Dishwasher

I have a whirlpool gold dishwasher model Quiet Partner 3. The top rack is not cleaning the dishes very well. We live in the country and have hard water. I am wondering if there could be a buildup of some sort inside the water arm and causing it to block some of the water. I am wondering if I could put something like C L R in the washing cycle to loosen up the buildup. Do you have any other ideas.


If it is just affecting the upper rack i doubt it is just a plugged spray arm (though i could be wrong). more likely than not you have a blockage on the intake of your spray pump motor. a series of bones, toothpicks, foreign material, etc could be bl ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My 12 yr old KitchenAid -Sculptura-Model KUDR24SE starts to fills with water and then does nothing else. It will eventually go through the cycles on the panel, but nothing is happening inside. End result is still dirty dishes with water sitting in the bottom that has to be baled out. Cups on top rack don't have any water on the indentations, so it's obvious that the thing filled with water and that's it. I had the motor replaced (supposedly with a new) one 2 years ago so I find it hard to bel


... Dishwashers

My Kenmore dishwasher leaked out through the door and into the kitchen. It appears it is not draining and once the water reaches a certain level, pushes out the door. It did this before and we thought maybe the drain was clogged, but couldn't see anything. Ran it again and was fine but has now done it again. Could this be the control module or the overfill control, or something else?


\012\012Hi,\012Here\012is a tip that I wrote that will help you with your dishwasher not\012draining problem...Dishwasher Problems - ... Kenmore Dishwashers

I have a Maytag MDB7600AWB dish washer. I have a door leak, dripping from the right side. I can not see anything that would allow it. It seems like it could be coming from the inside of the door. Also, there is heat and condensation on at the top of the door, above the leak. It could be that steam is coming from the top right and dripping down the door. Could you give me some idea about fixing the problem.


HI,Check for the following troubleshooting steps:Some leaking around-under-from the door on dishwashers can be traced back to a split in the spray arm. If the lower spray arm develops a split in it, the spray arm can turn too ... Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher

I have a Fisher and Paykel DD605i dish drawer. We have a U1 error code on the top drawer and had this same problem just over a year ago. A repair person replaced the inlet valve I believe. I am wondering if there are any tests I can put the machine through or if this is something I can fix myself to see what is causing this code.


... Fisher and Paykel DD605I Dishwasher

I don't have a model number right now, but the front door on my Admiral dishwasher is leaking at the bottom. I have changed the gasket inside the door panel at the bottom but it still leaks. This is a rental property and the renters did a job on this dishwasher. I was wondering if they may have pulled another lower gasket off that I didn't know existed. Something like a windshield wiper. The seal I changed was a foam strip 3 x 22 approx. Thanks for your time, Joan


It may not be the door that is leaking if this is an older admiral or whirlpool dishwasher the lever that holds the soap door closed has a little rubber seal that after time will let water in during the wash cycle it the runs down the inside of the d ... Admiral Dishwashers

The detergent dispenser [Main Wash] door doesn't stay closed. It seems like there is something wrong with the latch, but we can't what. We've cleaned it, but don't know what else to try. There don't seem to be pieces missing or broken. But no matter what, when we put in the detergent [we use the cubes] the door always just pops open and the detergent ends up falling to the bottom on the dishwasher. The dishes are still getting relatively clean, but we want to solve the problem with the door


... Frigidaire FDB1200RG 24 in. Built-in Dishwasher

I have a moffat dishwasher MSD 2000 p00ww I checked the drain hose, ran water trough it had no problem, hooked it back on to the dish washer. I blew into the hose an could see the the air bubbles no problem in the dishwasher. But it still won't drain. Just wondering if you could hep me, on what to try next. Your help would be great.


... Dishwashers

My Whirlpool Gold dishwasher has been wonderful until recently. In the last 2-3 weeks, the top rack of dishes does NOT get clean - AT ALL. It appears that the spray arm is not moving, or at least not moving much. What can I do myself to check this out and possibly take things apart to see if something is clogged?


Take a tork #20 screwdriver and remove the screen go all the way to the choper and make sure its not broken on clogged. ... Dishwashers

GE Quietpower 2 spray arms not rotating. Sounds like pump is working and water is moving inside but arms are still in same position when I check to see if they've moved. Of course the dishes don't get clean. What's up with this?


... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

GE TRITON dish washer. Utensils are stained after wash. I tried all that suggested solutions like cleaning with white vinegar, make sure hot water flows before it starts. I donot think we have hard water problem and also tried Jet dry rinsing. Nothing is working still i see utensils soap stains and not completely rinsed. I am desperately looking for an answer. I am thinking of is there a way i can test whether the middle tower is really opening up to spray water or not. It might be something els


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Maytag Dishwasher

Drying problem Hi Our 3-day old LG dishwasher is not able to dry our dishes. After the cycle is finished 2 hours later, I open the door to find that water is everywhere. As if the washer is skipping the dry sequence completely. The "vent" on the inside of the door doesn't seem to have an outlet--why is this a vent if nothing can escape? The owner's manual says to use a rinse aid to help drying. I don't believe in using band-aid's; something else is wrong. Any help/advice is appreciated. Thanks,


Hi,\015\012\015\012As I had the same problem, I worked on my machine and found out the heater unit was not working (it is a brand new machine ! - remark : as I moved overseas, LG did not cover it with their warranty).\015\012\015\012But b ... LG LDF6810ST Stainless Steel Built-in Dishwasher

The inside of the dishwasher used to sparkle & clean the dishes very good, now the dishes look dirty & inside looks dull with a white film. I have tried cleaning filters & taking arms offs to check for blockage, making sure the Jet Dry dispenser is properly filled, the hose going to the dishwasher does not appear to be kinked, how would I check inside the dishwasher to see if it's kinked there? Do you have any other suggestions? please help!!!!


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 23 in. SHU33A Built-In Dishwasher

Dishes are not coming clean they have grit on them at end of was I just got a new dishwasher and dishes DO NOT come out clean. I tried a few different detergents, and I see that something is wrong with the dishwasher. It doesn't clean well. I'm so disappointed. Is there something I can do that will make the dishes come out clean?


Clean the dishwasher use one cup of blech then change the type of dishwasher cleaner ... Frigidaire PLD4375RFC Dishwasher

Dirty dishes We have a built-in SMEG machine and it washes 75% of the dishes perfectly. However there is a build up of sandy'ish residue round the inside of the door (mostly on the ledge at the top) at the end of each wash and some of that sticks to the inside of glasses, cups and mugs. Have checked all the filters we can see and they are clean.


Check manual,your water hardness and salt/detergent quantities can make a big difference,theres usually some switches you can adjust for salt/detergent,if not check for partial blockage in pump etc,may be not enough water comming through. ... Smeg 18 in. DWI410 Built-in Dishwasher

Not cleaning my dishwasher goes thought all it's cycles,but when it is done the dishes are still greasy and the top dishes are still dirty.i have checked the water pressure the psi is 64. i have also cleaned all the wands and drain.can you please give me something less to do.my dishwasher is only 3 yrs old. i have not been able to use it in about a year know.


Check the wash arms make sure that they can spin ... open in mid cycle check water level and arm spin...also check water temp... hope it helps ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

I have a Maytag dishwasher with stainless inside and 6 months ago it stopped geting dishes clean..We live in the country and so use well water and seem to have a build up of minerals on the inside..but the dishes come out still quite dirty and we have to hand wash..


... Maytag MDB6709AWS Stainless Steel Builtin Dishwasher

Dishwasher is not drying. At end of cycle, dishes are still wet and damp, as well as the inside. Buttons are all pushed. Also, it seems to wash for more than one cycle. Did a light wash and after 1-1/2 hrs., it was still running. Purchased a couple of months ago. Dishes don't seem to be as clean as my old dishwasher.


Hi,Check your heating element.. A bad heating element causes many problems in dishwashers…Dishwasher Problems The ... Whirlpool MDBH969AWB Builtin Dishwasher

On normal wash cycle the dishes are still greasy and there is food debris on the inside door the machine has water and runs through its cycle but the dishes especially the top rack is still dirty.rnThanks Kimi


Depending upon the age of the DW, you may have a restricted or bad pump. You also could have a restriction in the drain line that goes to your sink. ... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1468 seconds