Having problems with your Whirlpool GU2400XTP Built-in Dishwasher ?

Getting it started

\015 I know this sounds dumb but i just moved into this house with this type dishwasher and i don't know how to operate it nothing seems to start it up can you help\015

Answers :

Here's the manual:
http://shared.whirlpoolcorp.com/product_literature/search_results.jsp?searchTerm=gu2400xtp&siteCd=WHRCOM
Repair Help & Product Troubleshooting for Whirlpool GU2400XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My kitchen aid dishwasher will not start I replaced the interface control board thinking that was the obvious problem. When you go to set the dishwasher to start some of the settings don't always light up then when you push the start button the lights will flash then start but it's not flashing and won't start. I get lucky once in a while and get it to flash then start. I don't know where else to look. I don't want to start replacing parts one at a time till I get lucky. My model # is KUDIO1F


Check all cables especially the ribbon cables from the user interface to the electronic control assembly as steam from dishwashings will create small amounts of corrosion and inhibit signals to and from these 2 components,unplug each,inspect,and reco ... KitchenAid Dishwashers

I HAVE A NEW CRAFTSMAN PRESSURE WASHER WITH KEY START. I HAVE USED IT ONCE AND WHEN I TRIED TO START IT IT WAS HARD TO START HAD TO PULL START IT. NOW IT WONT START. LET PRESSURE OUT HAVE HOSE OH AND RUNNING, NEW SPARK PLUG HAS OIL, GAS FILTER FINE.HAS GOOD COMPRESSION, BUT WILL NOT FIRE GET SOME RECOIL. GETTING GAS TO SPARK PLUG AND GETTING SPARK. IM LOST PLEASE HELP.


... Pressure Washers

Pots/pan light blinks alternately with the normal wash button. Sometimes the cycle will start and then the lights come on. Once they start blinking, the cycle stops and I can't get it to start again. Unplugging it for a few days has worked a few times. But it just keeps getting more frequent. If it does start up, it heats fine and washes perfectly.


... Whirlpool DU1055XTSQ Built-in Dishwasher

We have Frigidaire model # FGHD2433KB1. The problem is that we cannot select a mode to get it to start. We unplugged it and the light for China Wash lights up, but it will not start. The number 92 appears in the window on front appears for about 5-seconds and disappears for about 30-seconds and does it all over again. We cannot get it to start.


... Dishwashers

I have an Electrolux EWDW6505G Dishwasher. Had started a cycle, then opened the door midcycle when water was in the tub -- and accidently pressed "cancel." When I try to start a new cycle now, I was getting an "Error 01" message. After trying to get out of it, I'm now getting a "water serv" message. How can I reset?


... Electrolux EWDW6505GS Fully Integrated Dishwasher with 9 Wash Cycles, Nylon Racks, Wave-Touch Contro... 24 in. Built-in Dishwasher

Lights work, dishwasher works but "start" button won't start it. I can get it to work sometimes by hitting a few of the buttons back and forth. Otherwise, I can't get it to start.


... GE 24 in. Monogram ZBD6880KSS Stainless Steel Built-in Dishwasher

I purchased my KARCHER G2500VH last summer. I used it one time for about an hour. I tried to start it today, seems like its not getting gas. I checked the gasline to make sure gas was flowing. I removed the sparkplug, poured a little gas into the engine through the plug hole. Replaced the plug, pulled the rope and it started for about two seconds. I also poured fresh gas in tank. Cannot get to start.


Have tried to start our BlackMax 2700psi pressure washer, it is not getting gas to the carburetor, what to do? ... Pressure Washers

I'm having trouble starting my ge profile dishwasher; the machine locks but then when I push the start button one of three things happen: 1) I get error C3 and I do not have a user manual) 2) nothing happens 3 I get the screen indicating that the machineis a sensing soil level, washing' but in fact nothing happens - I do not hear the motor starting and no water runs, thank you!


... GE 24 in. Profile PDW7800 Built-in Dishwasher

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Home Depot has a lawn mower with the Honda GCV160 Electric start version engine. They also have a pressure washer with the Honda GCV160 engine. I have a disability that makes it difficult to pull the starter rope. I would like to get the electric start on the pressure washer. My local Honda bike shop service center said they use different blocks. Can I get a pressure washer pump mounted to the Honda GCV160 Electric start version engine? If necessary, are there adapter plates that can be purchase


... Karcher 2500 PSI Pressure Washer

Dishwasher motherboard(switchboard) I cant get my dishwasher to start when push start button and now not all wash options light up. How can I get to start up again?


... Whirlpool Dishwashers

All of a sudden about 1 month ago my stainless steel dishwasher started getting a strange white film on bottom which now is starting to turn crusty, It is affecting the soap dispenser badly and certain black plastic utensils being washed come out with this white film. Mysteriously, all the dishes, glasses, silverware come out perfectly clean. What is causing this? It is getting worse.


You could try adding vinegar to clean the white film off. If you wanted to be aggressive with it try using CLR to clean off the film from the dishwasher. ... KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

MODEL#MDB7760AW CANNOT GET START BUTTON ON PANEL TO STOP BLINKING 99% OF THE TIME AND IT WILL NOT START WHILE IT IS BLINKING. HOW DO I GET IT TO JUST STAY ON AND NOT BLINK


... Maytag Dishwashers

FDW60 Fault Hi, I have exactly the same problem. My dishwasher starts and washes ok but appears to get very hot during the drying phase and then the two lights fast and eco flash warning of a heater problem. I suspect either the heater, thermostat or control PCB. As the rest of the cycle seems of and the water gets hot then I'm assuming the heater and thermostat are OK. When the dishwasher attempts to dry is when the problem starts. Did anyone find out what there fault was? Thanks


Hold down the start key and you will re- set the D/W. Please Rate This !!! Thank YOU !!! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Hello, I have a CONSTRUCTA S9W1C dishwasher with aquastop. Unfortunately, I tried once to start it with the house water supply closed. Of course it stopped after a few seconds. After that time, when I start it, the water pumps works and after some seconds the cycle stops. It gets no water. I've checked and noticed that no water passes through the aquastop valve. The aqua stop has two wires that get into the dishwasher. Do you have any suggestions? Thank you for your time Alex


... Dishwashers

Bosch Dishwasher I have just moved into my flat where there is a Bosch dishwaher installed in the kitchen. I have tried on a number of times to get the dishwasher to start a programme but for some reason it fails to start. It does switch on but I dont know how to operate it. I dont have a manual for it so have not a clue what to press to get the programmes running. I would be grateful if you could help. Bosch Dishwasher logixx Model Number SGS6952GB/13 Installed 2001


Dear Saps,\015\012Go to https://portal.bsh-partner.com/portal(bD1kZSZjPTAwOQ==)/PORTALFRAME.HTM for a pdf download for an Intr ... Dishwashers

I have a Briggs and Stratton power washer Quantumpower 5hp water driver series 1750 PSI 2.0 gal min model # WGV1721 . I got it used and it was always a bit hard to start but always started. Pull cord frayed and broke I bought new cord and a neighbor replaced for me. Now it does not want to do anything when pulled. I can't get top cover off that has screws with round holes instead of phillips or standard slots to get to pull cord winding


Spray well with WD-40 or similar, and take a small chisel, on it's edge, and hit hard enough to allow chisel to dig in to head of screw, making a "V" like slot in the head, then angle chisel slightly and start tapping in direction of loosening(counte ... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle

Have a 665-16293201 dishwasher with electronic controls and smart sensor. Approx 10 years old in great shape. it just started having a problem - it takes a long time for the sensing to be completed at the start of a wash and then the washer will start and display a time - like 92 minutes - turn the sensing light off, then start to wash and count down. when it gets to 86 minutes, it starts to sense again and will continue washing while displaying 86 and with the sensing light on. It will keep


... Kenmore 24 in. 16293 Built-in Dishwasher

Start button not working...can't get machine to start


The micro switch is bad. I had the same problem cleaned the switch a few time (nd bought some time) but in the end I moved a switch from a cycle we did not use to the start position. Cost was nothing but my time (must have skills in soldering PCB ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Hello. I have a Kitchen Aide KUDG255HWH1 that will not start from a cold state. The "Energy Saver Dry" and "Normal" indicator light/ switches failed to operate about 1 month ago and since then I have needed to use the "High Temp Wash" and Soak & Scrub" cycles to get the unit to run. Now these two indicator kight will illuninate but the unit will not start when I depress the "On" soft switch. When I depress the cancel switch the unit starts with what sounds like a pre-start cycle. Pleas


Hi\015\012\015\012\015\012\015\012\015\012\015\012Thanks for using FixYa. To reset the dishwasher switch\015\012off the dishwasher from the power socket and mains for five minutes and then\015\012switch it back on. If still the issu ... KitchenAid Dishwashers

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Maytag Quiet Series 800 dishwasher won't start. The only button that I can get to work is pressing and holding the locking feature--that light eventually comes on. A couple of times I came back in an hour or so or the next morning and hit the start button and it started right up. Now it won't start at all. VERY FRUSTRATING!


... Maytag 24 in. MDB6100A Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1002 seconds