Having problems with your Whirlpool GU2400XTP Built-in Dishwasher ?

Using power cord for dishwasher

\015 I am installing a built in dishwasher. the house never has had a dishwasher before, the install instructions say i can use a power cord instead of direct wiring. the install inst. say has to be at least 16 guage. the question is how many amps. the guy at lowes said to use at least 15amps, but the one they have that is 15amps is only 14 guage, the one they have that is 16 guage is only 13amps. thanks\015

Answers :

Any utility cord the orange or yellow one will do fine just make sure it is on a breaker that no a lot of large things are on like microwave or computer ect .
Repair Help & Product Troubleshooting for Whirlpool GU2400XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Using power cord for dishwasher


Any utility cord the orange or yellow one will do fine just make sure it is on a breaker that no a lot of large things are on like microwave or computer ect . ... Whirlpool GU2400XTP Built-in Dishwasher

The dishwasher won't start, its stuck, pots/pan button is blinking, & the timer has (2)_ _ bars blinking. I tried to reset/pushed the start/resume button nothing happened. I pushed the cancel/drain button still nothing happened. I close the door tight..nothing. I check the trays if there something stuck inside..nothing. I unplug/replug the power cord nothing? my wife was using it when this got stuck about 3 weeks ago.


Did you hold the start/resume button for at least 3 seconds if this works the dishwasher will start ok but if there is a fault it will fail again best you contact your nearest service agent good luck ... Whirlpool GU2400XTP Built-in Dishwasher

My dishwasher did not come with power cord. what kind of cord do it need and how do i connect the cord? On the new cord how will i know which one to connect to the white and black wire? The dishwasher is Whirlpool model du930pwsb, Sku numbmer 451-5344.


120 Volt 16 gauge, 3 wire power cord.\015\012\015\012Brass Screw is Black, White Screw is is Common, Green is Ground....Try Home Deport for a cord. If no screws are on the dishwasher, use wire nuts and elec. tape ... Whirlpool 24 in. DU930PWP Built-in Dishwasher

An electrician switched off the power whilst doing other work. Power was restored OK. But when we came to use the dishwasher there appeared to be no power to it i.e the control panel remained blank. We have checked the fuse box and all appears to be in order.The appliance is a Siemens FD 8909 dishwasher


Maibe the internal fuse of the dishwasher blow for a spike, check first if you have power at the socket if so is highly posible that you have a blown fuse in the dishwasher ... Siemens Dishwashers

This dishwasher is older than most living people in this business. It works great except it is a 208 three phase unit. It is in St.Peter's church in New York Mills, MN. We bought it used during our remodel project in 1994 for a price of $800.00. That was our mistake. We had a converter installed to accomadate the 3 phase power supply. So we have this converter running 24 hours a day using up electricity and we use the dishwasher four times per year. I am wondering if we could replace the motor o


This unit is a dinosaur. The 3-phase converter had to cost twice as much as the unit. Best solution - turn the power off to the 3 phase converter when not in use.Better best solution - find a newer unit that will be repairable should it n ... Hobart AM14-253 Free-standing Dishwasher

I have a Frigidaire 4000 Series Dishwasher, Model# FDB4315FCO, almost six years old. It acts as if there is no power. There is no error code. If I pull the power cord I get a "PF" message.


... Dishwashers

Matsui mf145 my dishwasher not working power& water on power light on next 2 light on but can't program it not been use for last 18 months


... Dishwashers

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

Dishwasher LG Dishwasher does not turn on suddenly. No power. I have checked power cord and it is good.


If you have confirmed power to dishwasher, you are pobably looking at a control board. I have only run into this one time on a LDS5811 so far. Parts on LG dishwashers have a two year warranty. You have to dissassemble the door to replace the part. ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

Dishwasher has NO POWER! Circuit breaker ok. It worked the last time we used it. No other appliances or lights are out. It appears to be only the dishwasher that has no power. Weird!


Turn breaker off hard to reset it then on2-3 times ... Dishwashers

I would like to purchase a Moyer Diebel U/C dishwasher for residential use. I have the option of purchasing a used dishwasher - it could be one of three models. Which one is the model he is trying to sell to me? 1. 501 HT 2. 501 HTN 3. 501 LT the owner states the voltage is 120/208-240 and heats between 150 f and 180f.He notes there is a 4 ft. cord at the back without a plug on the end of it but the model is rubbed off of the serial number tag.There are three switches on the lower right hand co


The way you mentioned the unit have a 4 ft. cord at the back seem like a 50l LT the best way to determent is open up the bottom plate and see whether there is a booster tank in the right hand side. \015\012Hope this can help you. ... Moyer Diebel 24 in. 501HT Built-in Dishwasher

I just bought a used LG LDS 5811ST stainless steel built in dishwasher. The previous owner said he bought it 4 years ago. It's in great shape but doesn't work. It powers up but the water is not pumping into the dishwasher. The previous owner said that he thought it was the pump. He said he took it apart once and cleaned a bunch of crud out of some hoses and it worked for a while then started making funny noise and stopped. When i got it home i powered it up and connected water hose. It seems to


Rom the Service Manual:"1E INLET ERROR Not reached to the normal water level in spite of 10 min. water supply.The Hall sensor is OK?Check the frequency of Inlet Water by the Test Mode." ... Dishwashers

The power cord in my install kit for the Kenmore 1344 dishwasher, isnt color coded. The power cord is 3 leads of course but the manual says nothing about which lead to connect to the color coded wires coming from the DW. halp?


It does not matter what lead goes to the white or the black. You just need to make sure that you have the ground in the right place. If it is a flat cord then the center wire is the ground and if it really matters the lead on the right of the ground ... Kenmore Dishwashers

Dear Sir/Madam,I have owned a Beko DW450 slimline dishwasher for 13 months and used it only twice, i wanted to use it last night but when i switched it on the drain pump activated and would not switch off. I powered down the dishwasher to see if that would reset it but unfortunately when i started it again it did the same thing - drain pump activated but would not stop running, it is impossible at the moment to carry out a wash programme. Does anyone have any idea on this problem. Thanks, Patric


... Bosch SHU5315UC Dishwasher

Hi, We have a Smeg ST 663 dishwasher that does work. However, sometimes when you want to use it and turn the power button on it beeps twice with the red light flashing and you can't get it to work or change the settings. Sometimes if we leave it for a while and try it again later it will work, but it is annoying as sometimes it won't want to work for ages and we really want our dishes cleaned! The dishwasher doesn't have many buttons on it (a power button, cycle selection button and 1/2 load


Hi,\015\012\015\012Turn machine on and press and hold the programme select button till the light goes out about 5-7 seconds see if this resets it if it does start a cycle and see what happens.Otherwise the pcb as its not responding to an ... Smeg Dishwashers

No Power Hi Timon90, I used the dishwasher like normal yesterday today I went to use it and there is no power at all. I have checked our electricity box and none of the switches are tripped. I have put the door in as hard as I can and have checked whether the electricity plug has been pulled out by accident. Can you suggest anything or should I call a serviceman. Thanks from Julie


Remove the door skin dont forget the two screws under the door in the middle,the control panel will lift off remove the power board(unclicks)remove the plastic case and see if its blown.But first also remove the lower kick plate at the front and chec ... Asko 24 in. D3350 Dishwasher

Dead dishwasher? I have an Prima LXP600 dishwasher that doesn't work - no power light, no beeps, no anything. I've changed the fuse and used different power sockets. Is there anything that I can investigate, or alternatively is it likely to worth calling an engineer? The machine looks almost unused (was in a repossessed house that I bought, so no history), so I'd like to think that it's got some life left in it!


Please find some help from the link below;\012\012\012http://www.repairclinic.com/Dishwasher-Repair-Help ... Dishwashers

Whirlpool dishwasher This dishwasher quit in the middle of a wash cycle,we had to empty it and wash by hand. I thought that maybe the breaker to the dishwasher popped but when checked it had not .I then noticed that there are no lights on the electronic key board .Even when not in use there should be one red LED that is lit. It almost seems as if there is no power to the dishwasher. Is there some type of backup safety switch or breaker on the dishwasher itself that I could reset?


Fuse on control board. ... Dishwashers

My Bosch dishwasher, model SHX46A05UC/30 has been working fine. I ran it once today on the Power Scrub Plus cycle (always use this one). Shortly after unloading the dishwasher I needed to run it again with more dishes. Within a few minutes of running the dishwasher I heard loud, almost grinding noises. Nothing appears to be stuck. Any ideas on what to do? This dishwasher has always been quiet up until today.


... Bosch 24 in. SHX36L05UC Stainless Steel Built-in Dishwasher

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Dishwasher does not seem to have power. I have a Kitchen Aid, under counter unit, 9 years old, model KUDS01I. I used it 2 nights ago with no problem. When I push a button, nothing happens, no lights show, etc. It is plugged into the lower half of a duplex socket with disposal plugged into the top. Disposal works, so the problem seems to be with the dishwasher. That also eliminates any issues related to breakers or ground fault indicators, etc. Is there a reset button on the dishwasher? Is there


... KitchenAid Dishwashers

Hi. I had f1 appear on my Gisher and Paykel dishwasher. Unplugged from wall. Few days later dried using a hairdryer. Took cover off pcb board and dried in there as well. There was water on bottom of cabinet so understand the F1. Problem is now, I put cover back on pcb board and tried to power up but it is dead? Any sensor.microswitch on PCB cover, or anything i may have missed? No power at all to unit? Any assistance greatly appreciated. PS - Wall socket finer as powers other appliances.


Wait.................. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a 6th sense dishwasher purchased new October 2004. It has been working properly and then has just stopped the next time I tried to use it - it will not turn on no matter what buttons I push - no response. I have checked the power out let with another appliance and that works so it is not the power supply from the power point. I can only think it must be a fuse or the controller. Can you please advise best course of action? Thanks Helen


I rang the appliance man to fix the problem.\015\012\015\012Thanks anyway Helen ... Westinghouse Dishwashers

I have a AEG OKO_ FAVORIT 4040 dishwasher which has had very little use despite its age. The problem is that the switch that detects an over-fill is activated all the time and the pump continues to try and empty an already empty dishwasher even when the main switch is turned off, the only way to stop this is to turn it off at the power point I have had some sucess deactivating this switch by tilting the dishwasher forwards however because of the angle it sometimes overflows when filling. The ma


Hi there,This could be a problem on the control board of the unit. It could be faulty and need replacement or you may try to access the board and try to clean it.Make sure upon doing this all electrical connection to the unit ... Dishwashers

I have a Briggs and Stratton power washer Quantumpower 5hp water driver series 1750 PSI 2.0 gal min model # WGV1721 . I got it used and it was always a bit hard to start but always started. Pull cord frayed and broke I bought new cord and a neighbor replaced for me. Now it does not want to do anything when pulled. I can't get top cover off that has screws with round holes instead of phillips or standard slots to get to pull cord winding


Spray well with WD-40 or similar, and take a small chisel, on it's edge, and hit hard enough to allow chisel to dig in to head of screw, making a "V" like slot in the head, then angle chisel slightly and start tapping in direction of loosening(counte ... Briggs & Stratton Pressure Washer Projectpro Spray Nozzle
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1915 seconds