Having problems with your Whirlpool GU2400XTP Built-in Dishwasher ?

I installed according to guide, but dishwasher will not fill with water. Pump sounds much too loud to be normal. Wiring was checked three times for correct connections. Water supply was checked twice for water getting through, no leaks and water supply on. Drain hose is connected correctly and is connected to house drain.


Answers :

You state the water supply is on.
\015\012Have you loosened the compression nut at the dishwasher ell to see if you have pressure to the water inlet to the dishwasher?
\015\012Remember the dishwasher will always run a little to make sure any residual water from the last load is out of the bottom, so you could here the pump run a minute or so with no water coming in.
\015\012If you have Pressure to the water inlet and no water coming in regardless of the cycle/ timer position, it is most likely a bad electrical connection or switch at the water pressure actuator which is were the compression drop ell connects to the dishwasher.
\015\012This is the one and only actuator to let the water in to the dishwasher.
\015\012So it could be one of or combination of five things: no pressure to actuator,the electrical connection the actuator is loose or bad, the actual actuator is bad or timer timer is bad.
\015\012Most likely it is a loose electrical connection or lack of pressure to the actuator
Repair Help & Product Troubleshooting for Whirlpool GU2400XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I installed according to guide, but dishwasher will not fill with water. Pump sounds much too loud to be normal. Wiring was checked three times for correct connections. Water supply was checked twice for water getting through, no leaks and water supply on. Drain hose is connected correctly and is connected to house drain.


You state the water supply is on.\015\012Have you loosened the compression nut at the dishwasher ell to see if you have pressure to the water inlet to the dishwasher?\015\012Remember the dishwasher will always run a little to make sure an ... Whirlpool GU2400XTP Built-in Dishwasher

Hello, I just installed a GE profile dishwasher (pwd9280n00ss) into my kitchen. I connected a hose to the valve water inlet, I connected the drain tube from my garbage disposal to the check valve flapper and then the the drain pump asm. When the dishwasher finishes washing the dishes, all the water doesnt drain out. Any ideas how I can correct this?


... GE Dishwashers

Bosch Exxcel Dishwasher (Enr SMS53E12GB/01 FD 9002) bought in July 2010. Error code 15 and "Check Water Supply" light on at same time. Have checked in-line filter in tap connection and all clear, water pressure OK, no kinks/twists in supply hose. Any help would be greatly appreciated - I'll have to call Customer Service in the end as it's outside of my problem-solving ability, but would like to check whether there's a known reset or fix I can try before I call.


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Our G1140 SC starts with the drain pump running and then after draining all three amber lights come on and stay on and the dishwasher does not fill with water. I have checked the water supply which is on and connected.


... Miele Dishwashers

GE GSD4920Z dishwasher. Problem is that it does not drain completely at the end of the cycle--about an inch of water remains. After checking for clogs, etc, we followed a troubleshooting procedure which involves a hard reset (power off, then reset twice at beginning of cycle) and this procedure successfully drains the tub. However the next time that it's used on a normal cycle, water remains again. Suggestions?


Hi\015\012\015\012\015\012\015\012Thanks for using FixYa.\015\012Dishwasher not draining properly or not draining at all issues can arise due\015\012to different reasons. Usually, these issues are related to kinked hoses,\015\012knocked o ... GE 24 in. GSD4920Z Built-in Dishwasher

Subj: ge dishwasher mod/gsd3960looss - 1yr 4 mos old. problem: will not drain only used 6 times. last use after cycle done, water remained. had to hand drain. removed cover and checked drain area, no debris found. drain tube is connected to disposal by clear plastic tube; no clog in tube. the sink drains are clear and the disposal works normal. dishwasher drain seems to be stuck in closed position. this model has the touch pad controls. any solution????


... GE Dishwashers

Hello , we have a blanco BFDWC65 dishwasher supplied to us by our builder , The dishwaser fills with water ok then once in cycle it starts (with all operating lights ) then stops , it continues to start then stop for the rest of the cycle , Quiet some time later it finished and then drained the water ok , now it struggles to get to the end of the cycle. have checked all filters , water pressure and for clogged hoses , everything is ok in that department. Any help would be apprieciated


I would suspect the control board in this type of behaviour. As the machine is new I advise no interference, but to open a claim under warranty. You would have all the warranty papers for this unit, or should have received them from your builder. The ... Dishwashers

My Kenmore Elite UtraWash Dishwasher won't drain completely. We have checked the hoses (water supply and drain connected to the disposal) - both are free of obstructions. We have taken the whole thing apart but can't get the plastic cover off to access the motor or "garbage disposal thingy" inside the dishwasher. All of the bolts were taken out, but it was still firmly attached. Didn't want to force it and potentially make the problem worse. Any suggestions before I call Sears Repair people


I have the same problem. The part you're talking about can be released from under the dishwasher to clean it. www.searspartsdirect.com has useful diagrams. I cleaned everyt ... Dishwashers

I have the E3 error on my Smeg DWI614 dishwasher which would indicate a heater error, however it is heating the water in the bottom of the machine but it seems to time out. The main issue seems to be that the recirc. pump is not running during the heating phase. I have taken the pump out, checked the connections etc. twice now and everything seems fine (the motor runs when tested). When I have done this (both times) the dishwasher has started again and run for 20+ cycles fine, then the issue com


... Smeg DWI614 Built-in Dishwasher

First 2 weeks ago i put an electric control module into the upper section. what comes on is the green flashing light for clean. in checking connections i found the paper for trouble shouting. i did what they said to do. they said hit the time saver - high temp - time saver - high temp. from there all the lights went on & the wash cycle started and ran. then it just stopped & the green light for clean just flashes. the water is still in the bottom & won't drain.


The error indicates that the machine has taken too long to drain the water. Do the following.\015\012 \015\012\015\012Switch off the machine, unplug or disconnect the ma ... Kenmore 16874 Built-in Dishwasher

My dishwasher started making a whirring sound around 20 minutes into its cycle. I took off the drain pipe to check for obstructions, however it was clear. I started the cycle from the start again, and it started the whirring sound from the start of the cycle. There was a small amount of water that drained into the bucket where I had placed the drain hose, however there was not much water in the machine to start with (I checked when it started whirring the first time and there was no water in the


Hi.\015\012\015\012A blocked pump in absence of water won't be noisy from start. Check that\015\012 the whirring sound is not given by the spray arms. Test without baskets\015\012 and check the spray arms assembly.\015\012\015 ... Fisher and Paykel DS605I Built-in Dishwasher

Hi. We have a Bosch 4072 6301 which is about 9 years old and has always worked well. Recently is has begun to leave dishes unclean, particularily on the top shelf but also on the bottom. I have checked the water jets for blockages, checked the drain (as far as it is accessible). The heating element stills works as there is steam when the door is opened. If I open in the middle of the cycle I can see water coming out of the jets correctly, I can't tell if the pressure is correct. Any th


... Bosch 24 in. SGS4072 Free-standing Dishwasher

Disconnected dishwasher and moved out in order to tile the kitchen floor. Ten days later reconnected dishwasher. Turned on water supply to leak check -- no water is getting into the washer. - Ran hot water from sink side to see if that would help, no such luck - Disconnected water line and water is in the line up to the connection point at dishwasher. Looked inside valve of dishwasher for obstruction - no such luck - Disconnected both ends of water line and blew in line to check for obst


... Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher

My dishwasher won't drain. It starts a cycle but doesn't finish draining the water. I checked the outlet hose and it's clear. I was able to siphon off the water and start a new cycle but the water still won't drain. Time to replace the pump?


Hi,\015\012Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Water will not drain ... Kenmore 15879 Built-in Dishwasher

How can I shut off the water supply to the dishwasher? It fills slowly with water from the top (while not running), and then water spills out over the kitchen floor. By pressing the 'Drain' button, the water will drain out, but I have to get to it before it floods. It takes about 4 hours for it to get to the overflow stage. It is a Jennair model, about 9 years old. We have a lot of limescale, it is probably time to replace it, but for the moment my main concern is to stop the leak. Thank you for


Most water supply lines are attached to the hot water supply under the kitchen sink. If not it may be accessible from the basement somewhere under where the dishwasher is located. Regarding the issue with the dishwasher, the inlet water v ... Sears 24 in. 14181 Built-in Dishwasher

Hello, I have a CONSTRUCTA S9W1C dishwasher with aquastop. Unfortunately, I tried once to start it with the house water supply closed. Of course it stopped after a few seconds. After that time, when I start it, the water pumps works and after some seconds the cycle stops. It gets no water. I've checked and noticed that no water passes through the aquastop valve. The aqua stop has two wires that get into the dishwasher. Do you have any suggestions? Thank you for your time Alex


... Dishwashers

I have a Miele Dishwasher 2430 Sci. It's been not used for 5 months and when I returned it worked fine for several times (at least 6). NOW the intake/drain light keeps blinking. I have already cleaned out the drain and replaced it properly (there was nothing in there and it was clean). No water is coming into the dishwasher?however I know that the water hook-up is on (the first thing I checked). I turned the water on and off several times and AM SURE it's on now. What else could be


The usual course of events is to check and clean the filter, check and clean the water pump and well, check and clean the waste pipe and any connection to a sink or waste disposal system, then check the inlet warer pressure, then the machine level / ... Miele G2430SCi Dishwasher

I have a Miele 590G dishwasher. Everything appears to work except for water supply. Any suggestions about what I could do or what could be broken? I opened the supply connection (the small gray box) and checked the filter - all seems good. But still - no water supply! Thanks in advance. Ross


You must to check also the tap of water which connect water to this small box may the water pressur out from tap is weak .\015\012you can use a small pan to help this test.\015\012 thanks ross ... Miele 24 in. G656SCi Plus SS Built-in Dishwasher

Kenmore model #363.14672100, approx. 10 years old. After the wash cycle, sometimes not all the water drains. This doesn't happen all the time but when it does, the next time I run the dishwasher, water runs out under the door. We have hard water and am guessing there is some build up. How can we correct???


... Kenmore 24 in. 15079 Built-in Dishwasher

DW fills up with water after sitting. When I turn off the water supply it does not fill up. Removed solenoid valve and cleaned the filter and check for possible blockage. Put back together and turned on water supply. did not fill up until we used it for the first time after my fix. Could the solenoid valve not be sealing off completly DW is a Bosch SH5316UC/U12


... Bosch Dishwashers

STARTED DISHWASHER BEFORE BED--WENT TO EMPTY IN THE MORNING AND FOUND SOAP ON THE DISHES AND WATER IN THE BOTTUM--I TRIED TO USE THE CANCEL AND DRAIN BUTTON TO DRAIN THE WATER BUT THIS FAILED --ALSO I CHECKED THE DRAIN HOSE CONNECTION UNDER THE SINK TO SEE IF IT WAS PLUGGED THERE BUT IT WAS NOT. WHAT SHOULD I DO NOW--WAYNE HENSLEY


Have you checked the drain filter inside the wash compartment ? If that gets clogged up with food by products, the water cannot get to the pump to be removed to your house drain. Since you did not provide a brand and model, I cannot tell you exactly ... Whirlpool Dishwashers

MyTecnik dishwasher, TKD795/3 is draining out as soon as you switch on and continues doing this even with the door open. If you reset and try to start a new programme ot continues to drain and the water tap symbol comes on. I have disconneted to water supply and checked the little red filter and it was fine. The water pressure seem fine and not sure what to do now.


... Tecnik 18 in. TKD7000 Built-in Dishwasher

I can not get the water to drain during a normal wash cyclr. When I press the start/restart button twice it makes noise but no water comes out the end of the drain hose. I have put a shop vac on the end of the hose and can get water out that way but it appears not to be pumping. The washer sits for up to 6 months at a time without being used. Thanks for any help Ted Berry Placencia, Belize Central America


Teddy,\015\012\015\012Buy a new one...then go fishin!\015\012\015\012Richard Vantine (ret'd Colonel...USAF) \015\012Bingelrade, The Netherlands ... GE GSD5310D Dishwasher

We have a Siemens dishwasher SE25M851. It had the check water light on, so we have checked all water flows which seem fine. There is what I think is an Aquastop connected to the water hose, which I have no idea if the problem is there, but when I now put the dishwasher on there is a burning smell coming out of it, so have had to turn off power supply. Can you shed any light to the problem?


... Siemens Dishwashers

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1769 seconds