Having problems with your Whirlpool GU2400XTP Built-in Dishwasher ?

GU2400XTPQ6 Whirlpool Clean LED blinking 7 times

\015 Unit started to blink 7 times, could not reset. Could not initiate wash. Entered di (sani-rinse, heated dry, sani, heated) and cycled through diagonstic procedure. No. 3 proved to produce a humming sound but no movement. Diagonstic cycle completed. Smells a bit like burnt wiring. No smoke evident. Was it from Number 3? All LEDs have been cleared. Dishwasher can start cycle but still hums. I cancelled the cycle.Prior to failing, dishwasher motor was getting louder and louder. Dishes were not getting cleaned. Used vinegar wash, different detergents, to no avail. Carefully took bottom assembly apart from the inside (not underneath) and cleaned out screen. Worked well for a month, and then became noisy and finally failure (7 led lights blinking).What is wrong with this three year old machine?? I am willing to fix it myself, just need directions on what to replace and where I can get step by step instructions.Thanks in advance!Rob\015

Answers :

Repair Help & Product Troubleshooting for Whirlpool GU2400XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

GU2400XTPQ6 Whirlpool Clean LED blinking 7 times


... Whirlpool GU2400XTP Built-in Dishwasher

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

I have a Whirlpool Quiet Partner 2 and it simply won't start. The little GREEN light about the CLEAN button is blinking 7 times and then pauses. Then it blinks 7 times. Then pauses. It does this over and over.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes 7 times, pauses, and then repeats. When\015\012the dishwasher doesn't sense a ... Whirlpool Dishwashers

Whirlpool dishwasher clean button blinking 7 times


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Whirlpool gu2400 clean light is blinking 7 times


Yes this is a heater fault detection error. The unit may not be heating the water resulting in unsanitary dishes so the unit shuts down in this fault. Also the door may not have completely shut resulting in the heater not working, but everything else ... Whirlpool GU2400XTP Built-in Dishwasher

Whirlpool disher whirlpool dishwasher clean light blinking all the time cannot start whirlpool dishwasher


Run diagnostic by pressing Normal, heated dry, normal, heated dry, normal heated dry. a total of 3 times in 15 seconds. The dishwasher will reboot and run a test load. ... Dishwashers

Whirlpool dishwasher clean light blinks 7 times


... Whirlpool Dishwashers

I have a DU1050 Whirlpool dw and the green light was blinking 7 times. I did what you suggested and the dw reset itself and now works. Now my dishes on the top rack are not getting cleaned. The bottom shelf is cleaning fine, the top dishes are wet, but still dirty. Please help


... Whirlpool 24 in. DU1050SS Built-in Dishwasher

I have some problems with a Whirlpool DWF 406 dishwasher: The other day, my wife complained about it not finishing a program (just stopped and started bleeping). I saw a post at this forum where it said to clean out the black grid down my the sump. I did that, and then the dishwasher worked fine a couple of times. Today when I got home from work, the machine just bleeped at me and and the green LED light by the start button flashed 9 times over and over again. Does anyone know what those 9 flash


We have the same problem. The dishwasher is 10 years old. In one of the German forums they said that usually it's because the sieve ahead of the membrane has a fine layer of sludge and the pump cannot pump out the dirty waste water. They said that yo ... Whirlpool Dishwashers

The model is a Whirlpool # du1055xt5q3 I received infomation on how to get the clean light to stop blinking. I pushed the NORMAL WASH then HEATED DRY buttons in sequence and that worked, now it is doing the same thing and that doesn't work now. The light blinks 7 times at a time.Can this be fixed ?


Hi,The blinking always refer to a certain problem. 7 times blinking refers to defective heating element or control board.USUALLY 99% PEOPLE HAVE FAULTY CONTROL BOARD. YOU WOULD BE LUCKY ENOUGH IF YOU WOULD ESCAPE.R ... Dishwashers

I have the Whirlpool DU 1100 dishwasher and the clean light kept blinking. I did the heated dry, normal combination and got it to run through the diagnostic check and sure enough it cleared the lights and appeared ready to run. When I would start it up again it would run the water and then get to the soad wash cycle and stop. No more lights it just stopped. I have been through the diagnostic process 3 times and still same problem. HELP


... Whirlpool Dishwashers

The clean light blinks 7 times - Whirlpool 24 in. GU3200XTP Built-in Dishwasher


\015\012Hello & Welcome to FixYaFlashing clean light is reset by pressing two buttons in sequence 3-4 times, to reset your kenmore press these buttons in sequence: ... Whirlpool 24 in. GU3200XTP Built-in Dishwasher

Gu1200xtkq0 clean light blinks 7 times - Whirlpool 24 in. GU1200XT Built-in Dishwasher


... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Whirlpool Quiet Partner II clean light blinks 7 times


The clean light flashing 7 times is an error code indicating an issue with the wash temperature. If the control does not detect a 4*F temperature rise in the main wash cycle, it will display the fault as the clean light flashing 7 times. There are se ... Whirlpool Dishwashers

I have a Whirlpool GU2700XTSB1 dushwasher. It stopped one day and cleanning light was blinking. I was able to reset the dishwasher by pressing two of the button 3 times. Now when I run the dishwasher it fills the bottom with water, heats the water and then buzzes. The wash motor does not spin. Any help?


... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

Stopped runing will not start and clean. led blinks 7 times, then repeats


If you Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher blinks 7 times and then repeats, indicates a problem in the dishwasher which should be investigated and not just the control 'reset'! That is why the control will not let the dishwasher star ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Clean light blinks seven times - Whirlpool Dishwashers


... Whirlpool Dishwashers

Whirlpool model du1100xtpq6 machine will not start clean lite flashes 7 times stops and repeats must be code 7 blinks only drain pump runs when drain/cancel button pushed


Hi, this is an indication that the water did not heat properly. Follow this link to some instructions I put together to help solve this and reset the control so you can use the machine again. ... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

Why is My whirlpool quiet partner II the clean light blinks seven times


... Dishwashers

I have a whirlpool dishwasher the clean button blinks 7 times trying to find out what code is


This may help in your situation. The following link explains how you may be able to clear the blinking clean light problem:http://www.f ... Dishwashers

I have a Kitchen Aid Dishwasher KUDROITJBLO that has the "clean" light blinking 7 times. I have cleaned the filter but that did not help. I have shut the power off but when I turned the power back on the clean light start blinking 7 times. Any suggestions?


... KitchenAid Dishwashers

Clean light blinks 7 times pauses 1 second and repeats. will not work. the light above the clean cycle indicator blinks 7 times. I can not run the dishwasher, When I press start the light above the start button blinks and will not start


Hi there,\012Well first of all you reset this by pressing - High Temp Wash, Heated Dry, High Temp Wash, Heated Dry, High Temp Wash.If you don't have a heated dry then use "air dry"This sequence help you to reseting the e ... Whirlpool GU2400XTP Built-in Dishwasher

I have a kenmore dishwasher mdl#665.16022401the clean light blinks all the time and i push the cancel button and then wash and the start and the start button light blinks 3 times and nothing happens.the clean light is still blinking.


... Dishwashers

Whirlpool dshw won't run-clean bttn blinks 7X-need codes to reset


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes 7 times, pauses, and then repeats. When\015\012the dishwasher doesn't sense a ... Whirlpool Dishwashers

Blinking clean light on my Kenmore 665.17052400 7 times Did the "reboot" normal wash,heated dry sequence which made the machine work for a while. then it would go less times in between needing to be "rebooted", now it will not go through a cycle w/o the clean light blinking even following a reboot. what is my next step? I have heard that this means the microprocessor will need to be replaced. is it even worth it?


No its about a buck forty but im sure you could do it your self ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1258 seconds