Having problems with your Whirlpool GU2400XTP Built-in Dishwasher ?

Start light flashes - lot of water in machine - she no work!

\015 ADP 951 dishwasher is not working - found a quantity of water in the machine after last wash yesterday - the start light is flashing but won't turn the machine on although I can get it started for about 20 seconds by holding the start button down for a while but then the machine cuts out. The machine is 9 years old but had little use.\015

Answers :

Check to make sure the drain hose and filter is clear
Repair Help & Product Troubleshooting for Whirlpool GU2400XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Start light flashes - lot of water in machine - she no work!


Check to make sure the drain hose and filter is clear ... Whirlpool GU2400XTP Built-in Dishwasher

My Miele intake/drain light is flashing. It seems to be an intake problem, because water drains out fine, but seconds after water starts going to the machine, it stops and the intake/drain light starts flashing again. We've cleaned the filter in the inflow hose, cleaned the arms, and it still doesn't work. Any suggestions?


... Miele Touchtronic G892 Built-in Dishwasher

Fisher & Paykel DW60. Fault: Will not start regardless of program selected. E.g. if "heavy duty" pressed, only light will flash, if "normal" is pressed, only this light will flash etc. All hoses (water and drain) have been checked and no crimps or blockages found at either end. All usual methods tried (e.g. cleaning strainers and filters, turning power off for a while etc). Finally, while lights are working, the machine makes no noise at all when a pogram is selected.


... Dishwashers

Hi our nemo dishwasher starts a cycle and fills but does not start cleaning cycle. Light under start button flashes. If start button is held on it resets and pumps out. We live in an area with high clacium in water. At first the machine only pumped out and did not start filling. I have cleaned the level sensor ( membrane switch filled with calcium) and it at least stopped pumping and started to fill. It does not proceed from here. I checked the level switch it seems to be working OK (NO and NC c


Hi.You need to move the appliance and check the height of the drain hose. If there is water in the tub you may have a syphoning problem (water refluxing in the tub) because of incorrect height of the drain hose elbow.The led t ... Fisher and Paykel Dishwashers

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

My 1yo slimline hotpoint dishwasher LST216 has developed a fault when trying to run the 'normal wash': washing stops after a couple of mins, the lights start flashing and the alarm comes on as soon as the water is being drawn into the machine. When I open the door I can hear a whirling/grating motor noise coming from the bottom of the machine. I have cleaned all filters and have run other programmes to check overall functionality and they all work as expected most of the time. I cannot unders


... Hotpoint Dishwashers

I have a BAUMATIC BDW8 which has started beeping when you close the door to start the cycle. You can hear a motor running but no water is being pumped in. When you re open the door half the lights are flashing. This is an intermittent fault, the machine will still work ok on occasion.


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete ... Baumatic 23 in. BDW8 Built-in Dishwasher

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

My Baumatic BWD 1631 will not start unless I close the door, hold down the programme button, press the on/off button, release the programme button, at which point all 5 programme indicators light up. If I then press the programme button again, the lights then all intermittantly cycle. However during this period, the bleeper sounds, the water inlet valve works, the circulating pump works and finally the discharge pump works and the machine empties. However I am unable to stop or start the machine


... Dishwashers

I have a Whirlpool ADF951, it has power to it and was working fine, the power light is on and the green light to the far right of the cycle lights is flashing, I can only get any response if I hold the start button in for about 10-15 seconds, The machine stops the light flashing and makes the noise like it is starting , that goes for about 20 secs then returns to the flashing light stage, any idea's please


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water tempera ... Dishwashers

FDW60 dishwasher - taken apart pump and that is clear. Seems that dishwasher fills, and empties and heats all OK but water wont go around the machine ie the motor pump doesnt start - any idea how to take this out and replace without having engineer around? Taken small pump apart and its clear. First of all the Eco and fast light flashed, then we took it apart with some direction from online discussion advice. Now Eco and Pre wash lights are flashing. Machine empties water, then fills with


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

My KitchenAid Model KUDE70FXSS 2 dishwasher is new to us today and has never been used before. It was hooked up professionally, but I assumed it would work, so tonight when I tried to run it, it lights up on panel, but it won't run any cycles. It will start putting water in the machine, but then cuts off. It starts making a grinding noise underneath the machine, and it clicks like it is trying to work, but the water doesn't wash. Hmmm. Anyone know what to do?


... KitchenAid KUDE70FXSS Builtin Dishwasher

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is ... Dishwashers

Hi, Zanussi dishwasher DE6344, when starting any program the machine start pumping (draining) for a while and then stops, lights start flashing saying that the draining is faulty. Checked the drainpipe and when adding some water the machine drains it perfectly, still the program won't start. Looks like it thinks there still water inside ? Suggestions ?


... Zanussi 24 in. DE6544 Built-in Dishwasher

The start button flashing continuously and the filter area seems to be full of water but when I take it out it is perfectly clean. I have switched the machine on and off several times but each time the start button indicates a fault. I have tried holding down the on button so as to stop the start button flashing so that I could select a program - this did work once and I selected my program but 10 mins in it stopped and started beeping... I have a ADG7460 machine - HELP! I'm going crazy!


Please clarify what you mean by "..but when I take it out it is perfectly clean.." are you saying the water in the filter area is clean. \015\012\015\012Turn the power off and take out all the water by hand using a small container. Turn t ... Whirlpool Dishwashers

When cycle starts after about 1 minute bleeping starts and when door opens the machine has changed the programme to the 1st programme (rinse) the light is flashing 7 times then pause then starts again, it sounds like the water is not getting into the machine, we have checked the water pipes for blockage and cleaned the filters?? Model is ADG7440


... Dishwashers

Water is not drining from the machine and when i drain it by hand i then start the machine it brings the water in but does not start the wash the eco and fast light come on flashing what can i do to solve the problem.


Shut iff the water disconnect the drain line and clean out the drain pull the entire unit out and disconnect the drain that goes into the drain pump clean and make sure there is nothing clogged in the drain line. remove the drain pump and do a bench ... Dishwashers

I have KitchenAid dishwasher KUDS01FLSSD. The sani-rinse butten keep flashing and not let me start the machine. Other buttens are not working. When I push the sani-rinse butten with cancel butten with door closed, it makes sound that water is drainning, but there isn't any water in it! I tried 'sani rinse' 'energy save dry' 'sani rinse' 'energy save dry.' didn't work. Sani Rinse keeps flashing. Help me!!!


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have some problems with a Whirlpool DWF 406 dishwasher: The other day, my wife complained about it not finishing a program (just stopped and started bleeping). I saw a post at this forum where it said to clean out the black grid down my the sump. I did that, and then the dishwasher worked fine a couple of times. Today when I got home from work, the machine just bleeped at me and and the green LED light by the start button flashed 9 times over and over again. Does anyone know what those 9 flash


We have the same problem. The dishwasher is 10 years old. In one of the German forums they said that usually it's because the sieve ahead of the membrane has a fine layer of sludge and the pump cannot pump out the dirty waste water. They said that yo ... Whirlpool Dishwashers

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

Delonghi trend dishwasher you select programme and it starts and you hear the pump start and expell water and then u hear water going into machine for 10 seconds or so then it stops then programme selected light starts flashing and the dishwasher starts to heat as though it is in the drying part of the cycle


Please provide the full model number of the dishwasher.\015\012\015\012have you tried to turn the power to dishwasher off and back on.\015\012\015\012What program do you start with? Have you tried the rinse only cycle? does it ... Dishwashers

We have a Whirlpool ADG 7560 dishwasher which has recently started playing up. When switched on for a normal wash, after a short time the machine starts to beep. If you open the door the green programme light is on the pre rinse and the start light is flashing. After starting the cycle the few times eventually it works normally. Have cleaned all the filters etc.


... Dishwashers

We have a whirlpool quiet partner iii. It was working fine and was opened mid cycle. Then it wouldnt drain. Then all the lights started blinking. At some point it drained the water out. We flipped the breaker and now just the normal cycle light is flashing. Flipped breaker again that didnt work. Tried the reset code hi temp wash and heated dry. Normal light still blinking. Help please?


See this causes and fix it. God bles you\012 \012 \012 \012 \012 Check Fault Codes\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Dishwashers

We have a problem with our Miele G851 SC Plus dishwasher. We have not operated it for over three months as we were away on vacation and also because there were other issues in the kitchen due to some water flooding . Yesterday we switched on the machine and notice that the machine flashes the intake / drain light after a few minutes into the cycle and stops working. we have checked the drain pipe for blockages and also the water pressure is good. I disconnected the machine drain from the


Www.miele.ca/miele/canada/OperatingInstructions/.../G851%2005431311.pdf\015\012\015\012\015\012\015\012 ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1443 seconds