Having problems with your Whirlpool GU2400XTP Built-in Dishwasher ?

The clean light is blinking diswasher won't start

\015 I ran the diswasher, it ran through the cycle and stopped at cleaning, i can't get that light to go off by touching cancel/drain, i can't get the dishwasher to start a new cycle\015

Answers :

Push these buttons in this order High temp wash > Heated dry>High temp wash >Heated dry all the lights will come on and this will reset the board and run it through a short test cycle but more than likely it will come up again,It's a failure in the heating cycle either the heater itself or the turbidity sensor which sits mounted up into the tub right behind the drain pump...hope this helps
This same problem happened to my diswasher and I watched as the repairman did the button sequence in case it happened again. It did and I was happy that I paid attention. Then one night around 3:00 am (I always ran it at bedtime) I smelled something burning. I got up and looked around and found it was the dishwasher. I immediately went to the fuse box and shut it down. We called the company and was told that we were still under warranty for the electronics (check your warranty). They fixed it for free and it has been fine since. I do not however run the diswasher while in bed anymore.
Repair Help & Product Troubleshooting for Whirlpool GU2400XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Green clean light wont stop blinking unable to use dishwasher . It is an energy saver. the drain button works ..and when you push start the light comes on but will not run for cleaning


HiThanks for using FixYa. If the clean light flashes, pauses, and then repeats. When the dishwasher doesn't sense a water temperature increase, it stops working and locks the functions (clean light fla ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Kenmore dishwasher wont start blinking clean light


Today January 9, 2009...blinking clean light, kenmore dishwasher would not run,,,the solution on Fixya ..."keep hitting normal -heated wash-normal -heated wash buttons over and over...unlocked the blinking green light problem. Dishwasher is running a ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

The clean light is blinking diswasher won't start


Push these buttons in this order High temp wash > Heated dry>High temp wash >Heated dry all the lights will come on and this will reset the board and run it through a short test cycle but more than likely it will come up again,It's a failure ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Miela G1023 diswasher that will not start and inlet/drain light blinks after 30 seconds from pressing start. Cleaned the valve and pump as per manual but problem persists. Normally whwn all is well , can hear pump start.


... Miele 24 in. G665 Built-in Dishwasher

Clean light blinks 7 times pauses 1 second and repeats. will not work. the light above the clean cycle indicator blinks 7 times. I can not run the dishwasher, When I press start the light above the start button blinks and will not start


Hi there,\012Well first of all you reset this by pressing - High Temp Wash, Heated Dry, High Temp Wash, Heated Dry, High Temp Wash.If you don't have a heated dry then use "air dry"This sequence help you to reseting the e ... Whirlpool GU2400XTP Built-in Dishwasher

My dishwasher keeps blinking the "clean" light and will not start. I have tried turning off the breaker to reset the machine but it still wont start even after pushing all the buttons.


... Kenmore 24 in. 16049 Built-in Dishwasher

Stuck in clean cycle....clean light blinking but wont start new cycle


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Kenmore quyite guard ulta clean mod 665.1382 k605, wont start, lights blinking, wont cancel


... Dishwashers

I have a kenmore dishwasher mdl#665.16022401the clean light blinks all the time and i push the cancel button and then wash and the start and the start button light blinks 3 times and nothing happens.the clean light is still blinking.


... Dishwashers

The green clean lights blinks constantly, It will not allow me to cancel and when I try to start a new cycle the start light blinks a couple of times then the clean light starts again, but nothing happens.


... Whirlpool 24 in. GU2548XTP Built-in Dishwasher

Hi...my dishwasher 'clean' light continues to blink. I can hit cancel and it sounds like the cancel cycle is running. After that the light keeps blinking and I can not start the machine. If you hit start the light goes on, then stops, and the clean light flashes again. Any clues? Thanks!


Sounds like the control board or panel is shot. What is the model number of the unit, and serial number? ... Dishwashers

I have the kitchenaid dishwasher model #kudv03ctss0.the clean light stay blinking and when i hit the start it just blinks and then stops but the clean light stay blinking constantly.if i hit the cancel button i hear a um noise as if it going to turn on but nothing happens and the light stays blinking. what do you think might be the issue .


Dear friend,\015\012ngfam at you service! happy to assist!\015\012It's an electronic problem!The lights are called codes and need to be diagnoed by a factory service person!!We sell appliances for 65 years an ... Dishwashers

When starting my Bauknecht GSFP 5586 dishwasher the program is set for rinsing and the start light flashes two blinks, then again two blink etc. I cannot get the program to change. When I hold the Start button for 2 seconds, the progress light flashes at END for a moment then reverts back to the double blink sequence. I have checked the filter and it is well seated and clean. What can I do to start the program selection again?


Ok, so I had the exact same problem with the exact same model. NOT 7 blinks and to buttons that you do not have.\012I will tell you what I did as I do not know what (if any) of what I did fixed it (it could be luck but I do not think so).\012 ... Dishwashers

I have a Kitchenaid dishwasher KUDS01FL. On the control panel there is a clean light that is cycling 3 blinks every few seconds, It won't run. But will drain when you press cancel. But wont start. Any help would be appreciated


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

My clean light is blinking on my kenmore 16029 dishwasher and it won't start after I push the start button. The clean light is following a pattern of blinking 7 times and stopping, then repeating over and over again.


... Kenmore 24 in. 16029 Built-in Dishwasher

Model 66517022400 clean light blinking wont start


... Kenmore Dishwashers

Model gu2455xtsso the cleaning light is blinking 7 times and it wont canel or start


... Whirlpool GU2400XTP Built-in Dishwasher

Mdbh979aww3 clean light blinking and dishwasher wont start


... Dishwashers

When I push Start, the Start light blinks at me and then the little green Clean light keeps blinking. Nothing start, no water comes in, etc. No idea what the trouble could be.


... Kenmore 24 in. 16264 Built-in Dishwasher

I have a Kitchen Aid Dishwasher KUDROITJBLO that has the "clean" light blinking 7 times. I have cleaned the filter but that did not help. I have shut the power off but when I turned the power back on the clean light start blinking 7 times. Any suggestions?


... KitchenAid Dishwashers

I have a fridgidaire dishwasher model # FDB 1450chc2 andon the control panel the red lights are flashing and washer wont start ?? when I open the door the lights go out but when I close the door and push start the washing lights start to blink but doesnt start to work ?? Need help thanks [email protected] Brian


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Clean light blinking and will not run when start is pressed and red light blinks on start button


Hi,This is an indication that the water did not heat properly. Follow the link below to reset the control and find some tips as to why it failed and how to remedy it. Let me know if this helps. ... Kenmore 24 in. 15932 Built-in Dishwasher

I have a kenmore 665.15689000 and it won't start. The light on the pots & pans button blinks continuously. I have turned off the breaker and reset the diswasher numerous times. The dishwasher drains after resetting but the pots and pans light starts to blink again.


... Kenmore 24 in. 15689 Built-in Dishwasher

DISH WASHER DOES NOT WORK. CLEAN LIGHT BLINKS AND THE START LIGHT BLINKS 3 TIMES WHEN YOU PRESS START, BUT DOESN'T DO ANYTHING.


... Whirlpool 24 in. DU1148XTP Built-in Dishwasher

I have a Kitchen Aid KUDKO1ILBS1 which is constantly blinking clean. I have replaced the circuit board once because the capacitors were bulging blown out. After replacing the board the dishwasher has a mind of its own and will start when it feels like it. Now it will not start at all. Buttons do light up when pushed but it always retruns to blinking clean. Got a solution?


Hi\015\012 \015\012If the clean light flashes 7 times, pauses, then repeats...When the dishwasher doesn't sense a water temperature increase, it stops working and locks the functions (clean ligh ... KitchenAid KUDK01TK - Multiple Color Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1509 seconds