Having problems with your Whirlpool GU2400XTP Built-in Dishwasher ?

Our Ikea Nutid Whirlpool dishwasher locked up recently. It started when someone was wiping off the top of the door where the control buttons are located. The dishwasher was locked on the china setting. Holding the cancel button, shutting off the breaker did not seem to clear it. Is there a way to reset the dishwasher? There was flashing on buttons but I cannot remember how many flashes or what one was flashing.


Answers :

Repair Help & Product Troubleshooting for Whirlpool GU2400XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our Ikea Nutid Whirlpool dishwasher locked up recently. It started when someone was wiping off the top of the door where the control buttons are located. The dishwasher was locked on the china setting. Holding the cancel button, shutting off the breaker did not seem to clear it. Is there a way to reset the dishwasher? There was flashing on buttons but I cannot remember how many flashes or what one was flashing.


... Whirlpool GU2400XTP Built-in Dishwasher

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. My buttons on top are Accusense, pots&pans, normal, light, glass express, rinse only Soak and scour Hi temp wash


I think I just responded to this problem. Please accept both if you are happy with the solution. ... Dishwashers

My Whirlpool Quiet Partner IV dishwasher model number GU3600XTRY1 has stopped working. The normal light on the top panel is flashing and one lighted bar is showing in the start touch circle. Upon throwing the breaker in fuse box panel seems cleared but when you try to press any buttons it makes a starting noise for a few seconds then goes quiet and returns to the state above.. Thanks


... Whirlpool 24 in. GU3600XTRY Stainless Steel Built-in Dishwasher

I have a Kenmore dishwasher model 66574362K2. It has worked fine until tonight. I opened the door before the end of a cycle, closed the door, and pushed the cancel drain button. There was still water in the bottom but the dishes were basicly finished. Now I can not seem to get the dishwasher to come back on. The lock button seems to be on and it usually is not on. The manual says to push and hold the button for 4 seconds to turn it off. I did that. But now it is flashing between the Heate


Can you press the drain button to drain the water, then shut the unit off and restart??? I have exhausted all my resources to help, thought this may work. ... Kenmore Dishwashers

My kenmore dishwasher, model 665.16473300 has stopped working. Now the lights just flash at the Smart Wash, Normal Wash, and Cancel. I've reset the power and it just comes back. I've taken the drain area apart and made sure there are no obstructions. The buttons seem to respond, as after I reset the unit (breaker), only the Smartwash button is flashing. I push cancel and then it starts flashing. So I think the buttons work, but it's locked up.


IS THE WATER TURNED ON TO THE DISHWASHER ... Dishwashers

My dishwasher 'start" button won't kick in. The machine seems to think it isn't locked - light wont activate, but the door IS locked. I select the cycle and option, but when i push start, it won't stay, The "clean" button keeps flashing. This is 5 years old


Hi,How many Blinks are there?Is it 7 Clean Light Blinks?Let me know, so that we could proceed.Hope i helped you.Thanks for using ' Fixya ' and have a nice day!! ... Kenmore 24 in. 17032 Built-in Dishwasher

I can't seem to start the dryer. One of the kids pressed a few buttons on it when it was on there seems to be a lock on it that keeps flashing when I press the start button it is an Electrolux


Have you tried unplugging the unit, waiting for a full minute, and plugging it back in? Often, this will reset digital controls. If that does not work, can you post a model number? Some will display fault codes that enable troubleshooting. ... Dishwashers

Kenmore Elite Drawer Dishwasher model 465.13329600 Normal Wash and High Temp Wash buttons stay lit, as does green Lock button. The Start/Resume button and the red button on the front of the drawer keep flashing. I've tried key combos suggested above, but nothing seems to work. Even tried shutting it off at the circuit breaker to reset it, and that didn't work either. This ****** was purchased in 2006 or 2007, and hasn't been used very much. WTF?


... Kenmore Dishwashers

I have a Whirlpool Quiet Partner 2 dishwasher from Lowe's model DV 1055XTVS. The "clean" light flashes three times in a row over and over and the "lock" light is one. None of the controls will work. I unplugged it and that did not clear the problem. How do I unlock/reset the controls?


I have a whirlpool quiet partner 2, its brand new. It leaves a filmy residue on my plastic ware. I use the finish detergent as well as the rinse and no luck. Whats the problem.???????? ... Dishwashers

I think this is my dishwasher it does not have a number! When i close the door a noise starts then it bleeps but no water seems to come in. When i open the door more than one button is flashing.


... Smeg 24 in. STX2 Built-in Dishwasher

My Kenmore dishwasher model #66515639000 quit working. It was washing dishes just fine one day and then the next the buttons weren't working properly. The pots & pans button was flashing with the cancel button. After searching on your site, I tried to resent the control panel by pressing the normal wash button and the air dry button 3 times then opening and closing the dishwasher. Now the quick rinse button is flashing. Any ideas of what to do now?


... Dishwashers

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

Kenmore Ultra Wash Dishwasher Model 665.15779 LOCK ON light blinking on control panel, unable to use washer. If buttons were locked, LOCK ON light should be lit continually not flashing. If you press and hold NO HEAT DRY button to disengage lock, nothing happens. If you press the CANCEL button it begins to blink in unison with the LOCK ON light. How can I stop the light from blinking to allow button function again?


... Kenmore Dishwashers

Whirlpool Quiet II (DU110XTPB1)... Two problems (maybe it's one)... Start/resume light flashing and won't stop. I have tried on the different button combinations from this website and other websites and none of them seem to make a difference. The flashing continues. That's problem number one. Problem number two is that it seems to go into some sort of washing cycle in completely random intervals. When it's in one of the random washing cycles the following lights are on; Normal Soak and scour


Hope it's under warranty, maybe logic board, poor motor design causes main PCB failure ... Dishwashers

We have a Kenmore Ultra Wash Dishwasher Model number 665-13859K601. The Normal wash and the Cancel (drain) buttons are flashing red on the control panel. No matter what we have tried, we have been unable to correct this problem. Obviously the dishwasher does not function. When you close the door the lights keep flashing and no button combinations seem to do anything. I have looked at the troubleshooting guide that came with the dishwasher, however there is no


... Dishwashers

FDW60 dishwasher - taken apart pump and that is clear. Seems that dishwasher fills, and empties and heats all OK but water wont go around the machine ie the motor pump doesnt start - any idea how to take this out and replace without having engineer around? Taken small pump apart and its clear. First of all the Eco and fast light flashed, then we took it apart with some direction from online discussion advice. Now Eco and Pre wash lights are flashing. Machine empties water, then fills with


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Dishwasher I turn on the dishwasher and all the buttons flash, (no noise) i can go through and try and select a setting but when i press start nothing happens the buttons just keep flashing? Do you have an instruction manual or can you tell me how i would get one?


What brand is it? go to that web site put in model number and download it there. also you might have the controls locked press and hold the heated dry button for three seconds to see if that unlocks the controlls. ... Dishwashers

I can't get my electrolux dishwasher to run. It seems as though the touch pad is not responsive. It says to reset holding down the sanitize button, I do that it beeps but doesn't do anythng. All of the buttons are not lit up. I have to hold the delay start button along with the sanitize button to light the buttons up, still the buttons don't seem to be responsive, I touch the start and the lights go away and flashing numbers appear. Et 19 66 02 34 Any help would be appreciated.


... Electrolux EIDW6405HT Builtin Dishwasher

My Whirlpool Gold Quiet Partner III was DOA when I went to use it today. I unplugged/plugged it back in, at which time the "China Crystal" LED flashed a sequence of 3 flashes, then 3 more flashes, pause, 3 + 3 more, pause, 3+3 more, pause, etc., etc. And it would not run on any other cycle, but it did seem to run thru that one OK. Upon completion of the cycle, it was DOA again. Did the "Normal/Air Dry/Normal" button sequence, and now the Rinse Only button is steadily flashing. Any suggestions? I


When the rinse light is flashing steadily then the reset procedure for your model is pressing the "Normal/Air Dry/Normal" buttons.\015\012\015\012If it did not reset your dishwasher the control board must have fa ... Whirlpool GU2400XTP Built-in Dishwasher

Kenmore dishwasher Lock On light flashing


Holding the button for four seconds will not do it, you have to hold it until the light stops blinking and\015\012will go back to normal, normall takes more than four seconds to unlock the unit, this is something\015\012the sears repair t ... Dishwashers

I have a Kitchen aide dishwasher Model KUDI01ILWH6 that will not turn on..there is a control lock light on and I have tried pushing the cancel button but all that happens is the control lock light flashes 3 times and the dishwasher still wont turn on....Please , how to I disengage the control lock


... KitchenAid Dishwashers

My kitchen aid dishwasher will not start I replaced the interface control board thinking that was the obvious problem. When you go to set the dishwasher to start some of the settings don't always light up then when you push the start button the lights will flash then start but it's not flashing and won't start. I get lucky once in a while and get it to flash then start. I don't know where else to look. I don't want to start replacing parts one at a time till I get lucky. My model # is KUDIO1F


Check all cables especially the ribbon cables from the user interface to the electronic control assembly as steam from dishwashings will create small amounts of corrosion and inhibit signals to and from these 2 components,unplug each,inspect,and reco ... KitchenAid Dishwashers

I just bought this house with this dishwasher built in. I have pushed the door shut, pressed the heat dry button to lock the door and pressed the start button. Nothing happens. Now I can't even get the lights on front to turn off. The lock button flashes as though the door is open, but its not as far as I can tell. I have to press the latch in to open the door. I'd like to use it... any ideas. Its a Kenmore Elite model # 665 17052 402. Thank You


... Kenmore 24 in. 17052 / 17054 / 17059 Built-in Dishwasher

No Water Coming Into SHU43C05UC/12 Bosch Dishwasher: We have a Bosch Dishwasher, model number SHU43C05UC/12. It has been working for more than 4 years, but yesterday I notice that although I hear a motor sound, there is no water in the dishwasher. The LED display on the panel seems to be working all right. I ran a diagnostic pressing and holding Power Scrub and regular wash button then pressing the on/off button. Got C1 at start then P0 and the Regular wash and Quick wash flashing on/off. How c


... Dishwashers

Whirlpool adp 5550 Dishwasher wont complete a cycle. The light in the start button flashes four times in a continuous pattern. Have pressed the start button for 3 -5 seconds to reset after which the machine seems to operate ok then it stops and the start button returns to flashing. Have cleaned the filter and checked the sullage pipe for blockages What do I do next?


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2304 seconds