Having problems with your Whirlpool GU2400XTP Built-in Dishwasher ?

My GE potscrubber 1230 is leaking by the motor area. Do I need to replace the motor, or valve assembly to fix?


Answers :

Hi,\012
Here is a tip that I wrote about dishwashers and them leaking.

Leaking Dishwasher

heatman101\012
\012
\012fsdhgkdfosprsa
Repair Help & Product Troubleshooting for Whirlpool GU2400XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My GE potscrubber 1230 is leaking by the motor area. Do I need to replace the motor, or valve assembly to fix?


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101\012\012\012fsdhgkdfosprsa ... Whirlpool GU2400XTP Built-in Dishwasher

Dishwasher leaking we replaced the float switch. It is still leaking. Is there a valve that needs replaced? Would like to fix ourselves instead of paying $129 plus parts.


Try checking the rubber door seal if it is not sealing properly dish washer will leak just below the door it is easy to replace and not that expensive ... Kenmore Dishwashers

My bosch dishwasher sgs09a15 is leaking on or from the pump assembly can i repair the pump or do i need to replace the pump motor assembly completely en which do i need


I consulted another website ... Bosch Dishwashers

RY80940 The valve under the pump is leaking. I think it is a pressure release valve but I am not sure. I tightened it when I had to re attach two bolts that were holding the motor on the metal case then it worked for awhile then it started to leak and I lost all power. Should I tighten or loosen it or is there a washer that needs to be replaced?


... Pressure Washers

Unloader valve Thanks for the insight on my problem with a Karcher 550m. I have taken the pump motor out of the unit. How do I identify the unloader valve & replace it? There does not appear to be any other leaks. Is this the only part that needs replacing if pressure is down? Many thanks


... Pressure Washers

I have a leaky gate valve shaft seal that I want to replace myself (part # WD8X181). It only leaks when in the drain cycle. Repair manuals are not available for this model. How much disassembly is involved to replace this seal? Do I need to gain access to the shaft from inside the housing pump assembly (drain sump)?


... GE Dishwashers

Have a leaky gate valve shaft seal that I want to replace myself (part # WD8X181). It only leaks when in the drain cycle. Repair manuals are not available for this model. How much disassembly is involved to replace this seal? Do I need to gain access to the shaft from inside the housing pump assembly (drain sump)?


... GE Dishwashers

I have a Kenmore Dishwasher Model #665.168790000 and the water fills just fine and empties fine when cancelling cycle but when pressing any wash cycle the pump/motor just makes a loud humming noise and does nothing. I took apoart the lower assemblies to clean everything out but the problem hasn't gone away. Do I need to replace the motor or the whole motor assembly (also contains impeller kit)??? Also, I don't think I need to replace the whole sump & motor assembly do I???


... Kenmore Dishwashers

I have a GE Dishwasher: PDW8480JO1SS and it does not fully drain when I run it. I disasembled it and after finding a carrot deep in the pump area thought I had fixed it, but no luck. I also made sure there were no obstructions in the drain out to the disposal. Tee unit is about 6 years old. I don't know if I need to replace my pump or motor? Can you help? Thanks, Mark


... Dishwashers

I have a GE dishwasher (GSD4020Y70BB) new in 1996. I replaced the whole motor assembly in 2007, seal was leaking. My dishes are not getting clean now, dried food left on plates, coffee stains in cups not being cleaned. I removed main spray arm, found nothing, turned washer on and plenty of water gushing out. I took the cover off sump all clean. I removed the filter screen in the back, there appears to be a valve with some soft rubber around it. Water gushes out of this, does stop during the cyc


Have you checked the drain pump impeller and drain hose? I am curious if there is a back siphon from the drain hose or the waste outlet at the garbage disposal might be blocked or plugged with food debris.\015\012I wou ... Dishwashers

Leaks water from under dishwasher, some one suggested the fill valve assembly needs replacing???? kenmore


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If your\015\012dishwasher leaks, check these:\015\012\015\012 ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

GSD4911X02SS leaks from the bottom. Opened the bottom cover to see where the leak is and it looks like it's leaking in two places. The leak is ont by the door. It looks like the leake is by the pump or motor dripping down. The diswasher still works, but the leak needs to be fixed. Also I have pictures if you need to see


... GE 24 in. GLD6200L Built-in Dishwasher

It appears that the Inlet Valve is leaking on my Kenmore dishwasher. By replacing the inlet valve do I also need to undo the connection at the bottom with the teflon tape - or can I just undo the screws at the bottom of the plate and leave that connection alone? The dishwasher is 4 years old, could something be causing the valve leaking other than the valve being bad? Thanks! :))


Probably just hard water causing the solenoid to stay slightly open. \015\012Shut off water \015\012Remove 1/4 hose\015\012Remove wire harness/plug\015\012Remove other side hose should be a clamp.\015\012Unscrew mounting bracket and replace in the sa ... Dishwashers

GE 24in GSD980X Dishwasher water leak in pump &motor area


I had the same problem. There is no way of replacing seal/joint between pump and motor. It can't be taken apart w/o destroying parts, it only comes as an assembly. Costs around 130$ for pump/motor assy, so it might not be worth it. ... GE 24 in. GSD980X Built-in Dishwasher

Need to replace the latch assembly on Maytag dishwasher model # MDB5600AWW. How do I gain access to the area where I need to replace the part? I removed the 5 screws at the top, but can't seem to get the upper front panel off. I'm afraid of pulling on it to hard.


Remove all the screws on the inner door panel and lift it up it will be easyer ... Dishwashers

Karcher k3.68m leaks from the pump area. If I turn it on without holding the trigger down on the wand it will not blow pressurized water. If the motor is idle and the water is turned on then it leaks a lot from the pump area. What part should I replace?


... Karcher PSI Electric Pressure Washer

Removed rear toe-plate to detect leak. Leak caused by broken drain hose. Hose replaced. To do this the unit was tipped forward onto its front door to allow access to the base area. Water allowed to drain out the front base area. Unit re-assembled but now does not switch on. Water connected. Base-plate dry. No water was detected at upper-front control panel. Power is connected and reaching unit ( multi-meter test ). Tipping the unit forward seems to be the cause. Is there any fuse,


The micro switches are frequently replaced on the door handle and they don't need to ever get wet. A lot of amp draw burns those switches up while they are dry. If they were wet and power was applied then they got fried my friend. The good news is th ... Dishwashers

The O-ring behind the quick connect for the hose to the gun leaks. I replaced this oring and the leak stopped for about 30 minutes then started again. Do i need to replace all the orings in the unloader valve?


... Pressure Washers

We getting the error message LE on the dishwaser model #LDF6810ST. The repair Official repair man that came out to supposedly fix the dishwasher called LG to find out what was wrong with it and they told him to tell us that we need to replace the motor and wiring harness and the Technician told us to order the "motor and wiring harness" charged us $100 and left and the dishwasher that is only 2 years old and we paid a little over $800 for is still broke. Now when trying to order the "motor and w


Motor assy pn# 4681ED1004A is the motor you will need. ... LG Dishwashers

Kenmore Dishwasher Model #110703412 leaks, likely around the motor shaft. Are there motor shafts seals and how are they replaced? Does the motor assembly remove through the tub or does it require being removed from the bottom? Do you have to remove the dishwasher from the cabinet to do this job?


... Kenmore Dishwashers

I have a fridgidaire Gallery dishwasher model # FDB949GFS2. It was not spraying water while running, so I checked for clogged wash arms and hoses etc. So I replaced the motor assembly and now I hear the motor running, it fills with hot water but it is still not circulating water. Is there something else I need to check. Thanks Tom


Most likely the wash sump is blocked. Refer this diagram. You will have to open the sump (item 14) and loo ... Frigidaire FDB949GF Dishwasher

I have a Miele 24 in. G638 Plus Free-standing Dishwasher which is leaking into the pan underneath the machine (and triggering the polystyrene float switch) I am almost certain that the leak is coming from the main pump seal. Is it feasible to replace the seal (it looks like a major job to take the pump assembly apart). I guess Miele labor charges would make the repair not worthwhile Is there a service manual for this machine. I guess I would need it


Hi\015\012\015\012Please check the bellow link to have a detailed view regarding your query…..\015\012http://www.appliance-r ... Miele 24 in. G638 Plus Free-standing Dishwasher

My Frigidaire is leaking at the pump and motor connection. It is 10 yrs old and I want to know if it is worth it to repair it or do I need to replace it. The bottom door seal also came off and it has a small leak there as well.


Hi,\012I would replace it...\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101 ... Frigidaire 24 in. FDB435RFR Built-in Dishwasher

Tub leaks, with a partially filled tub (2.5 inches measured from the lowest point over the pump assembly.) Promblem occured after the washer was idle for 3 weeks. Have just replaced the main water inlet valve. The fill tube is not the source of the leak, the top arm feed is fine also.


I am assuming leaking when it is running, not sitting idle. Leaking from the door? Fill and run unit for 1 minute with no detergent. Open door. Are suds present? Suds turn into water when they drop to the floor. Suds can flow over the lip of the tub ... Maytag MDB7100AWB Dishwasher

I have a troy built pressure washer leaking gas from the air filter i looked around for advice and hurd bang against the carb and it will realease the float valve i did it and it worked but should i clean out the fuel in the filter area or the filter will it harm it as it is or should it be okay? the filter was soaked in gas dry now and when it happened the gas flowed from the air intake (behind the filter) if i need to clean out in there how do it do it and if i need a new filter


Definetly replace the paper filter and yes Lowes will carry them.if it does not leak now, I would leave it alone or you will be installing a nine dollar kit.The briggs kit # is 294260 is you choose to do it anyway ... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1532 seconds