Having problems with your Whirlpool GU2400XTP Built-in Dishwasher ?

Water not heating up and heating element not heating up either. Water is hot when coming into dishwaher.


Answers :

DSBELL, see if your model has a serial number in the range of FR3701001 to FR5008380. If so they had a quality issue with the heater. The element itself should be round and not angular. Call for service, it will be covered. If this is not the case you will have to ohm out the heater, should read between 10 and 30 ohms. If that's ok, make sure the door switches are operating ok, this heater runs through the nuetral side of that door switch. There is also a high limit thermostat on the right side of the motor that should read closed. Catriver...post back.
Repair Help & Product Troubleshooting for Whirlpool GU2400XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Water not heating up and heating element not heating up either. Water is hot when coming into dishwaher.


DSBELL, see if your model has a serial number in the range of FR3701001 to FR5008380. If so they had a quality issue with the heater. The element itself should be round and not angular. Call for service, it will be covered. If this is not the case yo ... Whirlpool GU2400XTP Built-in Dishwasher

Fills with water, sounds like it starts to pump water then stops, then start again. It attempts to start pumping water 3 or 4 times them turns off leaving the water in the tub. I have read about the water needing to heat up for the cycle to advance. When I check the water that is left in the tub it is warm but not hot. The heating element is not hot either. I did a continuity test on the heating element and it seems to check out ok. I also did a continuity test on the red wire from the heating e


You have a wash pump problem. can be 1 of 3 things. most likely something is caught in the pump impelor if not the wash pump motor may be faulty or ceized or it could be the capacitor for the wash pump motor is faulty. you can try removing the wash p ... Maytag MDB7100AWB Dishwasher

Kenmore Elite Stainless Steel 24 inch tall Model 66577963K701. The heating element works for "heated dry" but not for "Hi Temperature" wash. It used to do so and when I opened the door a nice blast of steam would come out. My hot water tank is a great distance from the washer so we usually run the hot water tap in the sink for a bit until hot water comes... but the heating coil no longer kicks in on any of the cycles (Smart Wash / Normal Wash ). The high limit switch works and as I said, th


... Kenmore Dishwashers

I have a Beko DE3542FS dishwasher which has stopped heating the water. I know the heater element is ok because I have had it tested. I was wondering if the thermostat was faulty if this would account for it not heating. The element has had 240v applied and becomes hot. So my reasoning is that it is either the thermostat or the programmer. Any suggestions?


... Dishwashers

I have no heat my hot water coming in is as warm as it gets and on dry it will not heat up. Is there a fuse or circut breaker for the element or do I need to replace it. Also if I could ask how hard is it to replace. Thank You Very Much Dino


Just call me on +263912639492, thta's easy.thank you.\012\012Dr. Kelson ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

No heat up of water or any temperature raise . Dryning not in functing either . Heating element without voltage supply, during normal sequence of operation. Has found relay Eberle with part no T-nr 3940620 in investigation of electrical loop. Please come up with a possible malfunction . Thank you very much Best regards Erik Rasmussen


... Miele 24 in. G665 Built-in Dishwasher

HDW101SS does not heat water. Heater element mearures 28 Ohms. Temp Limiter is N.C. Temp controllers TS50 & TS60 not found. On economy wash timer moves as normal then stops when red heater light should come on. If the timer is assisted one click it will progress as normal but no hot water.


Hi.If the temp limiter shows no continuity, there will be no voltage reaching the element contacts. The high limit is connected in series with the heating element. If the hi limit is open the element will not get power. Any technician wil ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

I have a whirlpool dishwasher DU915WKSO: when I turn the dishwasher on, the heating element comes on but no water comes into the unit. I recently replaced the garbage disposal and th dishwasher worked fine for a time or two. Since then I have only been able to get water in it once. Like I said, the heating element works but no water in the dishwasher. Thanks for any help.


... Whirlpool DU1055XTS Built-in Dishwasher

Conia CDW0305W dishwasher. Gets stuck on the cycle and has be clicked along to finish. Doesn't appear to be heating as it first sticks at a point I'd expect hot water wash and dishes come out with grease residue and still wet. I live in the middle of nowhere, to a professional will cost me a fortune. Is this the metal element and can I fix it myself? Please help, I'm sick of hand washing!!


... Dishwashers

Bosch Dishwasher I currently own a Bosch dishwasher. One of the selling points, if I'm remembering right, of the dishwasher was it was supposed to super heat the hot water that is coming in from the tap. I have 3 problems. We have to rinse the dishes by hand before putting them in the dishwasher, Otherwise they won't come out clean. The dishwasher will run for four hours sometimes longer. It doesn't seem like it is heating the water any hotter than what comes out of the tap.


Your control board is bad. ... Bosch 24 in. SHU43 Built-in Dishwasher

My kitchenaid dishwasher will not complete a washing cycle. the water heating seems to be staying on all the time. could my heating element be shot. the water seems hot when i open the dish washer during the cycle but it is connected to the hot water supply line. thanks


... KitchenAid Dishwashers

Ken wood kdw60w10 dishwasher no hot water, there seems to be no power to the inline heating element, showing 30ohms resistance and power directly applied when removed from the dishwasher and it heats up. No fault codes on panel, works normally apart from no hot water, any other ideas? Many thanks


... Dishwashers

I have a dishlex global 270 i cant find a model no i only have a serial and manufacturers no. What i wanted to find out is does this model have an element that heats the water. I only have one hose and when i used it with cold water it didnt heat up so i am using hot water.


Hi\015\012\015\012\015\012Thanks for using FixYa. I hope you understand that no one can tell you what are the specifications of the product until you provide the model no# however, dishlex usually have element in their dishwa ... Dishwashers

I have a GE dishwasher model GLDL560N10SS. I noticed a burning smell coming from it the other day and then realized that although I can hear water running into the dishwasher when I start it, it never actually runs in the sense that the water is pushed through the various outlets to wash the dishes. I'm assuming that it is because the unit is dry and the heating element is still coming on that it is causing a burning smell. If I open the unit and reset it, it pumps the water back out into the si


The problem sounds like it is in the water inlet selonoid. Pull off the bottom panel and this is the part that the main water line hooks to there is a selonoid and it has a plugg inconnection to it unplugg it and check for power when the unit is supp ... Dishwashers

Even though I turned up the thermostat on my hot water heater, the water in the dishwasher does not seem to be hot enough. Mold is growing in the food grinder and even though I choose the heat dry option, the dishes are never dry. Yet, when I touched the element, I got burned. The dishes are not getting clean because it doesn't seem to be hot enough to cut the grease.


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Hey, bosch sgs43a18gb/27 dishwasher not heating the water and hence the cycles take ages. ive read that plugging it into the hot water feed is not recomended, so is there a fuse on the element i can test? if not im assuming the element has gone in which case the washer is scrap as an element is £100 cheers


Hi,OK there is a NTC (temperature sensor) which is near the heater in the sump unit.Meter it out and check the wiring. You should get a reading in Kohms.But to be honest i have never replaced 1 of these on these m ... Dishwashers

I have a dishwasher model 66516979200 it doesnt dry the dishes i saw the heat sensing light on an opened it and felt the heating element and it was not hot at all ive checked the water temp at the sink and it is at 120 could the heating element be the problen or something else


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Doesnt seem like water is heating and element not getting hot


Sounds like you checked the basics. Do you have hard water? Our element got covered with calcium over time and didn't heat efficiently anymore. I was able to chip some off, then ran the dishwasher with LemiShine a few times. The element worked much b ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

I have a JDB1090AWS about 3 years old. We noticed a smell and found cutting boards and plastic cups melted. Machine was off. Had to turn off the breaker. Checked both leads to element & have power even with machine off. Not sure if it could be the limiting thermostat; I assume that is to shut the heat down when it gets too hot. Element is on though when it shouldn't be to begin with. I did have to tighten the water supply. Had some water underneath, but all wires seemed dry. Any tests I should t


The heat element can only get so hot.It's timed so it doesn't exceed a period of on, exposing dishwasher contents to continuous high temps.Watch the timer and take note how long it broils your cookware.Good luck. ... Dishwashers

DWF614SS not heating water, flow through heating element has been replaced and tested but still no hot water. Do I need to check the thermostat, if so, where is this located? Thanks for any help with this one. Owen.


... Smeg 24 in. DWF614SS Stainless Steel Free-standing Dishwasher

I have had a repairman come out and look at this and he says all the diagnostic test say everything is okay. My problem: my dishes come out dripping wet...like it hasnt dried anything. Sometimes dishes are still dirty. I don't think there is any heat getting to anything. I run the water in the sink beforehand to try to get the water hot. I used this dishwasher for 1-1/2 years with no problems and now I have this problem. What is going on?


I am having the same problem but do not see any posted solutions. Have you solved this problem? ... LG LDS4821ST Stainless Steel 24 in. Built-in Dishwasher

Yes I have a whirlpool DU1345XTVB1 dishwasher. Just got in July. After each wash cycle the dishes are not dry. I have been using Finish gelpacs w/jetdry & also have a off brand drying agent in reservior to help dry dishes. The water temperature is set pretty hot & washer is draining good. I have tried checking wash cycle a few minutes into 1st cycle to see if water is in filling & heating. Didn't know if maybe heating element going out or thermostat not working? Thank you for your time.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

We have a hotpoint DWF30P/17 Dishwasher which no longer heats or washes with hot water. The cycle completes the wash but no hot water. Can you advise? thermostat element controller


Before I went with the controller, I would probably try the heating element itself, they are usually not that hard to replace and may be cheaper. I know its not that much advice, but just trying to help. ... Dishwashers

GE Dishwasher SSD3900J00ww wash water cool heating element hot on


Crew that installed new cabinets and sink hooked dishwasher to cold water line I switch it works fine now. Thanks Don ... GE Dishwashers

Water temperature difference?? Does the brada dishwasher have a heatng element to heat the water if temperature of water not hot enough. If not, then the water entering the dishwasher is the issue. Th


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1618 seconds