Having problems with your Whirlpool GU2400XTP Built-in Dishwasher ?

Whirlpool dishwasher GU2400XTP stalls during cycle

\015 I have a Whirlpool dishwasher, model GU2400XTP that stalls out (always with 63 minutes remaining on the digital timer display). Sometimes it will resume operation by opening and closing the door, but other times we have to shut it off and restart the whole process. Any ideas?\015

Answers :

Sounds as if you have a faulty timer. These should be covered under warranty. Check you documents for duration of warranty.
Repair Help & Product Troubleshooting for Whirlpool GU2400XTP Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Whirlpool dishwasher GU2400XTP stalls during cycle


Sounds as if you have a faulty timer. These should be covered under warranty. Check you documents for duration of warranty. ... Whirlpool GU2400XTP Built-in Dishwasher

My Whirlpool GU2400XTP dishwasher keeps blowing the fuse. It sat up for 6months because the control panel went out and I couldn't afford to get a new one. Finally replaced the panel and the thermal fuse blew during the first wash cycle. I tried to put a 15AMP fuse in it's place to check it out before I bought a new thermal fuse and it too blew during the first cycle. Any ideas?


Are you replacing the wires along with the fuse? It is important to change the wires too as they are usually the cause for the fuse blowing. Be sure and get the fuse kit that includes the wires. \015\012\015\012Is your water too hot? Hot ... Whirlpool GU2400XTP Built-in Dishwasher

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!! I have the same problem. I took out the timer control and spraid it with contact clean


If the cycle doesn't complete, check these:Water-heating cycle ... Bosch SHU4006 Dishwasher

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!!


The Timer might not be bad. If one of the two thermostats is bad, the Dishwasher will exibit the same symptom. The thermostats are 141 deg. F and 161 deg F.They only cost $20 each. The Control Module is close to $200. ... Bosch SHU4006 Dishwasher

Light blinks won't cycle - Whirlpool GU2400XTP Built-in Dishwasher


On certian models there is a proceadure to stop it look under the dw for the book it will tell you how to take it out of this.the reason it goes into it is you closed the door from the side must only be closed from the center. ... Whirlpool GU2400XTP Built-in Dishwasher

What is the overnight cycle? - Whirlpool GU2400XTP Built-in Dishwasher


... Whirlpool GU2400XTP Built-in Dishwasher

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

Whirlpool Gold Quiet Partner Model # GU980SCGQ2 The dishwasher normal light flashes on and off continually. The dishwasher won't stop cycling now, everything seems to work normally other than it won't stop cycling. I've attempted turning off the breaker- no luck. Attempted resetting the dishwasher- no luck. Any assistance would be appreciated. Is this a problem with the control module? The thermal fuse?


... Whirlpool 24 in. GU980SCG Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to res


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

Dishwasher (Whirlpool Model DU930PWQ0) won't pump out. Problem occurred after door was opened during a cycle. Then the pump-out function ceased to work. Washer fills and pumps correctly during the wash cycle. Any suggestions? My guess is that the electronic control may be faulty and it is not opening the solenoid valve for the drain cycle. The other option I have thought of is that the solenoid valve may be faulty and is not responding to the signal from the controller. The dishwasher is n


... Whirlpool DU930 Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to reset the


... Whirlpool GU2400XTP Built-in Dishwasher

Whirlpool dishwasher DU1015XTXBO Stopped working during cycle, acts like don't getting any power. Checked the plugin and it works. No lights or anything coming on the dishwasher. Its like it just


... Whirlpool Dishwashers

Whirlpool Dishwasher won't drain during normal cycle


As you say a clogged line or valve does not make sense.\015\012\015\012Try running it without the heated drying and see if it empties or if the cancel button will work then.\015\012\015\012The dishes should air dry quickly if ... Dishwashers

My Whirlpool dishwasher stutters loudly during wash cycle. It's an intermittent thing, in the sense that sometimes when i run the dishwasher it doesn't do it at all. But also in the sense that when it does do it, it's for like a couple of seconds, then fine for a bit, then stutters again for a few seconds, fine for a minute etc etc. Sound is coming from inside, kind of like the power is turning on and off rapidly. It's a Whirlpool ADP-8540 Stainless Steel (Made in Germany)


A symptom like this is commonly caused by a failing wash pump motor. If you are having this problem and the dishes are not getting as clean as they used to, the motor is most likely the problem. ... Dishwashers

Whirlpool dishwasher DU945PWPQ2 four year old machine - never used. Water lines are attached properly and are clear. When dishwasher is turned on the wash cycle light turns on. cycle completes but water does not enter the machine.Water does not enter the machine.


... Dishwashers

Our Bosch SHU43C06UC/17 dishwasher stopped working properly today. The power scrub cycle starts at 115 and counts down to 112 and then stalls -- no sounds of water entering the unit... no further counting down The regular cycle starts and shows 97 and counts down to 94 and stalls. no sounds of water... no further counting down. We hear a constant buzzing sound. Can you help?


... Bosch Dishwashers

I have a brand new whirlpool DU1055XTV5 dishwasher, installed two days ago. After the cycle completes there is about 1/2" clean standing water left in the bottom. It is not just down in the well area, the whole bottom is covered with water. This is after running a normal cycle with no other options such as sanitize or heat dry. I called Lowes, the store that sold/installed it, and they said this is normal in new dishwashers to keep the parts wet. They said as long as the water does reach th


... Whirlpool DU1055XTS Built-in Dishwasher

Dishwasher Whirlpool ADG7540. Does not complete cycle. Approx 20 minutes into cycle dishwasher appears to get stuck on rinse.The water is cold. Machine stops and makes a constant beeping noise and the green light flashes 3 times repeatedly.


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

My WHirlpool dishwasher won't drain - basin is full of water. Machine starts and runs the drain cycle, but something is clogged. I opened up the bottom, and pulled off the drain hose to the disposal, and that had no water in it, so the clog is somewhere before the water gets to the hose. If I run the dishwasher drain cycle, it is not pumping water into the hose. What next?


The clog could be in the hose,or on up in the mouth of the drain,air pressure might dislodge the clog,or dissasible of the drain pan in the machine. ... Dishwashers

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

Sears kenmore dishwasher; model: 665.13763K600 (made by Whirlpool). Dishes have debris after washing in all cycles. Arms spin, water is running, dishwasher drains, and I removed the sump assembly to clean the chopper inlet. How do I diagnose it. I put it into diagnostics cycle and am unable to identify the issue.


... Kenmore 24 in. 16012 Built-in Dishwasher

I have a Whirlpool Gold (Quite Partner) Dishwasher that is about 9 years old. I was using a liquid gel Dishwasher liquid and it has been working fine. After I switched to a Cascade Action Pads (solid powder pallets), its detergent dispenser did not open during the wash cycle. I cleaned the dispenser and switched back to liquid gel. Now the detergent dispenser (that looks clean and fine otherwise) has stopped opening during the wash cycle. What's wrong and what can be done? I can be contacted


As well as controlling cycle times, the \015\012timer on many dishwashers also functions as an actuator for the \015\012spring-loaded dispenser door. At a certain specific time during the \015\012cycle, the timer will activate a lever that in turn op ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My Dishwasher starts, then stops after 30secs and won't continue draining. Everytime I turn it back on it comes up on the steam cycle and won't go to any other cycle, drains for 30secs and stops again. Power light is flashing. Have tried holding power button down for 10secs with no effect. Filter is clean, pipes are straight-no kinks. How do I get it to start working again? It is a whirlpool dishwasher, ADP5550.


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1950 seconds